ADT Security Services Safewatch Pro 3000 Entrepreneur 3000 User Manual

– 11 –
)XQFWLRQVRIWKH7RXFKSDGV&RQWLQXHG
6160VADT-002-V0
23
456
789
0
#
STAY
BYPASS
CHIME
INSTANTAWAY
CODETEST
READYARMED
READY
MIC MESSAGE
RECORD VOLUME
PLAY
S TAT U SFUNCTION VOICE
1211108 7
9
13 234
65 1
18
17
16
15
14
1OFF
20
19
Custom English Display Voice Touchpad
(shown without swing-down front door)
IMPORTANT!
 •When entering codes and commands, sequential key depressions must be made
within 10 seconds of one another. If 10 seconds elapse without a key
depression, the entry will be aborted...

– 12 –
(QWU\([LWHOD\V
(QWU\HOD\
Entry Delays give you time to disarm the system when you re-enter through the
designated entrance door. You must disarm the system (simply enter your security
code) before the entry delay period ends, or an alarm will occur. The touchpad beeps
during the entry delay period, reminding you to disarm the system. There are two
entry delays (if programmed). The first is for your primary entrance and the second
can be used for a secondary entrance, where a longer delay is...

– 13 –
(QWU\([LWHOD\V&RQWLQXHG
([LW$ODUPV
Whenever you arm the system, the exit delay begins. If an entry/exit door or interior
zone is faulted when the exit delay ends (e.g., exit door left open), the system sounds
an alarm and starts the entry delay timer. If you disarm the system before the entry
delay ends, the alarm sound stops and the message CANCELED ALARM or CA is
displayed on the touchpad, along with a zone number indicating the faulted zone. No
message is sent to the Customer Care...

– 14 –
&KHFNLQJ)RU2SHQ=RQHV
8VLQJWKH>*@.H\WRLVSOD\DQG$QQRXQFH6\VWHP6WDWXV
Before arming your system, all protected doors, windows and other protection zones
must be closed or bypassed, otherwise the touchpad will display a Not Ready message.
1. Press [*
] READY (do not enter code first) to display
faulted zones.
2. Secure or bypass the zones displayed.
3.The touchpad’s READY indicator lights when all
protection zones have been either closed or bypassed.
4. Arm the system as desired.
Custom...

– 15 –
$UPLQJWKH6\VWHP
6WD\0RGH$UPV3HULPHWHU2QO\(QWU\HOD\2Q
·Used when you want to arm the system with persons staying inside (or if you have
pets that are moving throughout the premises).
·The perimeter sensors are armed, but interior sensors are left disarmed.
·Exit delay begins (you can leave through the entry/exit door, if desired).
·An alarm sounds immediately if any protected perimeter window or non-entry/exit
door is opened.
·You may otherwise move freely within the premises.
·Persons...

– 16 –
$UPLQJWKH6\VWHP
$UPLQJ&RPPDQGV
Before arming, close all perimeter doors and windows and make sure the Ready to Arm
message is displayed.
Modes of Arming
Mode Press these keys… Touchpad Confirms By…
Stay security code + [3] (STAY)
·
 three beeps
·
 armed STAY message displayed
·
 red ARMED indicator lights
Night-Stay security code + [3] + [3]
·
 three beeps
·
 NIGHT-STAY message displayed
·
 red ARMED indicator lights
Instant security code + [7] (INSTANT)
·
 three beeps
·
 armed STAY message...

– 17 –
$UPLQJWKH6\VWHP
6LQJOH%XWWRQ$UPLQJ
The “A”, “B”, “C”, and/or “D” keys on your touchpad may have been programmed for
single-button arming. Note that while it will not be necessary to use a security code
for arming, a security code must always be used to disarm the system.
If Single-Button Arming is programmed:
·A function key has been assigned to a specific type of arming: STAY mode, Night-
STAY mode, AWAY mode, or STEP-ARMING (see Step-Arming paragraph).
·You DO NOT need to enter your security...

– 18 –
8VLQJWKH.H\VZLWFK
8VLQJWKH.H\VZLWFK
Your system may be equipped with a keyswitch for use when arming and disarming.
Red and green lights on the keyswitch plate indicate the status of your system as
follows:
Green Light:Lights when the system is disarmed and ready to be armed (no
open zones). If the system is disarmed and the green light is off, it
indicates the system is not ready (one or more zones are open).
Red Light:Lights or flashes when system is armed in AWAY or STAY mode.
See your...

– 19 –
LVDUPLQJDQG6LOHQFLQJ$ODUPV
8VLQJWKH>2))@NH\
The OFF key is used to disarm the system, silence alarm and trouble sounds, and
clear alarm memories.
IMPORTANT
: If you return and the main burglary sounder is on, 
DO NOT ENTER, but
CONTACT THE POLICE from a nearby safe location.
If you return after an alarm has occurred and the main sounder has shut itself off, the touchpad
will beep rapidly upon your entering,
 indicating that an alarm has occurred during your
absence.
LEAVE AT ONCE, and...

– 20 –
%\SDVVLQJ3URWHFWLRQ=RQHV
8VLQJWKH%