ADT Security Services iCenter 8132 User Manual

Security System Operation (Contd) 
21 
 SCREEN ACTION  
 7.  From this screen press the “Back” button to 
return to the “Arming” screen. 
How to Remove Bypassed Zones 
A bypassed zone will automatically be unbypassed when you disarm the system.  If 
the system is disarmed and a zone is bypassed, you can remove the bypass as 
follows: 
SCREEN ACTION  
 
 1.  View bypassed zones by pressing the 
SHOW ZONES button. The Zones screen is 
displayed.  
NOTE: W hile iCenter/iCenter-i is requesting 
and receiving...

Security System Operation (contd) 
22 
 SCREEN ACTION  
 2.  Remove zone bypasses by pressing the 
CLEAR BYPASSES button.  
 
 
 3.  The User Authorization screen is 
displayed with the instructions To Clear 
Bypasses, Enter Code. 
NOTE:  A zone cannot be unbypassed while 
the system is armed. 
Enter your 4-digit user code.  The More 
Choices screen is displayed showing the 
system as Ready to Arm. 
NOTE:  This will not occur if any zone(s) is 
open (not ready). 
  

Security System Operation (Contd) 
23 
 
How to Disarm the System 
IMPORTANT: 
IMPORTANT: IMPORTANT:  IMPORTANT: If you return and the main burglary sounder is on, DO NOT enter 
the premises, but call the police from a nearby safe location. If you return after an 
alarm has occurred and the main sounder has shut itself off, iCenter/iCenter-i will 
beep rapidly upon entering, indicating that an alarm has occurred during your 
absence. LEAVE IMMEDIATELY and CONTACT THE POLICE
 LEAVE IMMEDIATELY and CONTACT...

Security System Operation (contd) 
24 
 SCREEN ACTION  
 
 NOTE:  Once the system is disarmed, 
iCenter/iCenter-i will return to the Home 
screen after the selected “To Home Page 
After” time has expired.  This time is selected 
on the “Setup” screen. 
 
How to Disarm Using a Keyswitch 
To disarm the partition, 
    turn the key to the right and release. If an alarm has 
occurred, the red light will be flashing rapidly (memory of alarm). 
How to Check the Status of Other Partitions 
This system supports...

Security System Operation (Contd) 
25 
 
To check the status of other partitions perform the following: 
SCREEN   ACTION 
 1.  From the Home screen press the 
SECURITY button to display the Arming 
screen. 
 2. Press the Current Partition tab (lower edge 
of the screen; in this case it displays P1).  The 
User Authorization screen is displayed with 
the instructions “For Authorized Partitions, 
Enter Code”. 
 
 
 3.  Enter the code authorized to access other 
partition(s).   
If the code is accepted, the...

Security System Operation (contd) 
26 
 
 How to Send Emergency Messages 
An emergency message for panic or fire can be sent to the central monitoring station 
from the Emergency
EmergencyEmergency Emergency screen.  The Emergency
EmergencyEmergency Emergency screen can be accessed by activating 
the emergency icon located in the lower-right hand corner of the displayed screen 
(see next page for a typical screen).  
AUI-022-V0
EMERGENCY
ICON
  
 1. The Emergency screen cannot be accessed while running a...

Security System Operation (Contd) 
27 
 
How to View the Event Log  
Your system has the ability to record various events in a history log wherein each 
event is recorded with the time and date of its occurrence.  The control panel must 
be programmed to record various system events in installer programming mode.  
To view the Event Log, perform the following: 
SCREEN ACTION  
 1.  From the Home screen, press the 
SECURITY button.  The Arming screen is 
displayed. 
 
 2.  From the Arming screen press the...

Security System Operation (contd) 
28 
 SCREEN ACTION  
 
 
 
 3.  Press the EVENT LOGS button on the 
More Choices screen.  The Event Log 
screen is displayed. 
NOTE: W hile iCenter/iCenter-i is requesting 
and receiving the event log data from the 
control panel, the Event Log screen displays 
W ait For Event Log... 
 
 
 
 
 
 
 
 
 
 
 
 
 
To view additional events, press the up/down 
arrows to scroll through the event log.  To view 
all items, press the Show More button. 
NOTE:  W hen All...

 
29 
 
Fire Alarm System Operation 
 
Introduction to Fire Alarm System Operation 
Your fire alarm system (if installed) is on 24 hours a day, providing continuous 
protection.  In the event of an emergency, the installed smoke and heat detectors 
will automatically send signals to your Control/Communicator, triggering a loud 
interrupting sound from the Touchpad.  An interrupted sound will also be produced 
by optional exterior sounders.  A FIRE message will appear at your Touchpad and 
remain on until...

Fire Alarm System Operation (contd) 
30 
 
Recommendations for Proper Protection 
THE FOLLOWING RECOMMENDATIONS FOR THE LOCATION OF FIRE AND 
BURGLARY DETECTION DEVICES HELP PROVIDE PROPER COVERAGE FOR 
THE PROTECTED PREMISES. 
Recommendations For Smoke And Heat Detectors 
With regard to the number and placement of smoke/heat detectors, we subscribe to 
the recommendations contained in the National Fire Protection Associations 
(NFPA) Standard #72 noted below. 
    
Early  warning fire  de t e ct ion is...