ADT Security Services iCamera1000ADT Indoor LowLight Camera Installation Guide

iCamera-1000-ADT Indoor Low-Light Camera Installation Guide 
 
 
NOTE:  Please wait several minutes while the iCamera 
is being added to 
the network. 
 
10.  Once connected, click the Continue  button. 
 
 
11.  Click  Finish  after installation is complete.  
 
 
ADT Pulse®  Interactive Solutions 9 
  

iCamera-1000-ADT Indoor Low-Light Camera Installation Guide 
 
 
Figure  4: Installation Using POE Cable  
 
12.  Unplug the Y -cable from the ADT Pulse Gateway , and then power off the 
camera.  
 
IMPORTANT IF CAMERA WILL BE INSTALLED AS A ‘WIRED’  CAMERA, 
USE THE LAN CABLE AND THE Y- CABLE. (REFER TO 
FIGURE 3 ON PAGE 5 OF THIS GUIDE.)  IF CAMERA WILL 
BE INSTALLED AS A ‘WIRELESS’ CAMERA, USE THE POE 
CABLE TO SUPPLY POWER TO THE CAMERA.  
 
 
 
10  ADT Pulse® Interactive Solutions 
  

iCamera-1000-ADT Indoor Low-Light Camera Installation Guide 
  
Wall Mounting Instructions  
 
 
NOTE:  Ensure that the iCamera
 is properly configured and added to the 
network before mounting the camera. *
 
 
1. Stand Placement  
Locate an area where you want the iCamera  to be mounted.  Using the wall 
plate as a template, make two small marks inside the moun ting holes of the 
wall plate.   
 
2. Attach the Wall Plate to the Back of the Stand  
Place each screw in the designated slot of the wall...

iCamera-1000-ADT Indoor Low-Light Camera Installation Guide 
 
iCamera Wall Mounting Instructions (continued) 
4. Hook the two mounting holes on the stand into the mounting screws.   
 
5. Attach the iCamera Stand  
Locate the stand mount on the back of the iCamera. Fasten the stand by 
turning the iCamera counterclockwise until secured.  
6.  Mounting the iCamera  
Connect the PoE cable into the LAN port of the device.  
 
7. Connect the other end of the PoE cable to the adapter through the holes of...

iCamera-1000-ADT Indoor Low-Light Camera Installation Guide 
 
iCamera Wall Mounting Instructions (continued) 
8. Connect  the Power Adapter  
Connect the supplied power adapter to the PoE cable and power up.  
 
9. Check the LEDs  
The Power  LED turn s on briefly , and then starts  blinking for a pproximately 15 
to 20 seconds. After startup is completed, the Power  LED  and  t he  Network  
LED  re main  ON. 
 
 
 
ADT Pulse®  Interactive Solutions 13 
  

iCamera-1000-ADT Indoor Low-Light Camera Installation Guide 
  
PIR Video Motion Detection  
The motion event will be captured when a significant image changes within the 
Window of Interest. The Window of Interest is defined below.  
 
The following installation hints should be noted:  
 
1. Take care not to install facing direct sunlight, bodies of water, or areas of 
moving shadows as these can lead to unintended triggers . 
2.  Do not position the PIR camera facing a window or direct sunlight. The...

iCamera-1000-ADT Indoor Low-Light Camera Installation Guide 
  
Enabling Motion Detection via  the ADT Security System    
1. Click the Automation s tab , and  then click the Add  Automation button.  
 
 
2.  Select a trigger for this  automation from the Trigger  drop -down list.  
3. Select  Motion  from the Event  drop -down list.  
4. Select the conditions under which you want the automation action to occur 
from  Active  drop -down list.  
5. Click  Add Actions . 
 
 
6.  From the  Delay drop-down...

iCamera-1000-ADT Indoor Low-Light Camera Installation Guide 
 
8. Click  OK. 
 
 
9.  Click  Save.  
 
 
16  ADT Pulse® Interactive Solutions 
  

iCamera-1000-ADT Indoor Low-Light Camera Installation Guide 
 
Appendix A:  Specifications  
Model iCamera-1000 -ADT  
Dimensions , H x W x D  
(without stand)  
2.8” x 2.8” x 0.8” ( 72mm x 72mm x 20m m) 
Operating   
Temperature  
Outdoors: -4°F to 113° F (-20 °C to 45 °C ) 
Indoor s: 32 °F to 113° F ( 0 °C to 45 °C ) 
Storage Temperature  -4°F to 140 °F ( -20 ° C to 60 ° C ) 
Video Compression  H.264, MPEG4 and MJPEG  
Network Interface 1 Ethernet 10/100BaseT (RJ45)  
LEDs 1 LED indicator and 12  IR...

iCamera-1000-ADT Indoor Low-Light Camera Installation Guide 
 
Appendix B:  Regulatory Approvals   
 
FCC Statement   
This equipment generates uses and can radiate radio frequency energy and, if 
not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no guarantee that 
interference will not occur in a particular installation. If this equipment does 
cause harmful interference to radio or television  reception, which can be...