Home > Addonics Technologies > HDD/SSD/Optical Drive Enclosure > Addonics Technologies Ruby 25 HDDSSD drive kit RDCSSAESU user guide

Addonics Technologies Ruby 25 HDDSSD drive kit RDCSSAESU user guide

Add to Favourites
    Download as PDF Print this page Share this page

    Have a look at the manual Addonics Technologies Ruby 25 HDDSSD drive kit RDCSSAESU user guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 299 Addonics Technologies manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    View all the pages
    Page
    of 8
    Add page 1 to Favourites
    image text
    Enable zoom 
    							T E C H N O L O G I E S
User Guide
Ruby Drive Cartridge System
(RDCSSAES / RDCSSAEU)
www.addonics.com
www.addonics.com
Technical Support
If you need any assistance to get your unit functioning properly, please have your 
product information ready and contact Addonics Technical Support at:
Hours: 8:30 am - 6:00 pm PST
Phone: 408-453-6212
Email: http://www.addonics.com/support/query/
v7.1.11
    Add page 2 to Favourites
    image text
    Enable zoom 
    							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Enclosure Overview
Step 1
Separate the top from the bottom cover of the drive enclosure by loosening the 
screw.
Step 2
Align the SATA connector in the 2.5” hard drive with the SATA connector on the PCB.
Step 3
Wrap the shock absorbers around the hard drive and PCB.
Top Cover
Bottom Cover
PCB
Shock Absorbers
    Add page 3 to Favourites
    image text
    Enable zoom 
    							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Step 4
Turn over the PCB and secure the hard drive to the PCB with the mounting \
screws 
that come with the kit.
Step 5
Mount the board to the bottom cover.
Step 6
Put the top cover on by holding it in near vertical position and sliding\
 the two metal 
clips inside the two small slots on the rear of the bottom cover.
Step 7
Lower the front of the top cover and making sure the two covers lined up\
 properly. 
Tighten the small retaining screw on the front of the bottom cover to clo\
se the 
enclosure.
Bottom of PCB
Bottom Cover
    Add page 4 to Favourites
    image text
    Enable zoom 
    							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Ruby Enclosure
Switch:
INT: This mode is used when the enclosure is placed inside a drive cradle. Fo\
r 
drive cartridge system kits, this is the mode used.
EXT:  This mode is used if the enclosure is used as an external hard drive.
Ruby Drive Cradle
Note:  You can only use one power connector at a time. Either use the 4-pin 
Molex or 15-pin SATA connector but do not simultaneously use them.
Switch
Power & Drive Access LED
Mounting Holes for 3 ½” Drive Bay 15-Pin SATA
Power Connector7-Pin SATA 
Data Connector 
4-pin Molex
Power Connector
    Add page 5 to Favourites
    image text
    Enable zoom 
    							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Model: RDCSSAES
*Note: The Ruby Drive Cartridge System with the SATA interface must be connected 
to a SATA controller with hot swap capability in order to add and remove drive 
cartridge without rebooting. Please consult your motherboard or the add-\
in card 
manufacturer to determine hot swap support on your SATA controller. All of the 
Addonics SATA Host Controllers are hot swap capable.
Step 1
Connect a SATA cable to the 7-pin SATA data connector to the SATA interface of the 
cradle.
Step 2
Connect a 15-pin SATA power cable from your system’s power supply to the SATA 
interface of the cradle. This power connection provides power to the ruby drive 
cartridge system. 
Step 3
Slide the Ruby enclosure inside the cradle. To turn ON the drive enclosure, place 
switch on INT position.
Drive Cradle
Drive Enclosure
    Add page 6 to Favourites
    image text
    Enable zoom 
    							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Model: RDCSSAEU
This Ruby model will hot-swap.
Step 1
Connect the SATA to USB2.0 converter to the SATA interface of the cradle. 
Step 2
Connect the Y-cable that came with converter to the 4-pin floppy connector on 
the converter. The other end would connect to your system’s power supply. This 
power connection provides power to both converter and the ruby drive car\
tridge 
system.
Drive Cradle
SATA to USB2.0
Converter
Drive Enclosure
Drive Access  LED
Connector
USB B Type
Male Connector
Pin Header Type USB Connector
4-Pin Floppy Type
Power Connector
    Add page 7 to Favourites
    image text
    Enable zoom 
    							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Step 3
For data connection, you can either use the USB pin header cable to 
connect from the pin-header type USB connector on the converter to the 
USB pin-header on the motherboard. Or connect to the USB B type male 
connector on the converter to an internal USB port.
Step 4
Slide the Ruby enclosure inside the cradle. To turn ON the drive enclosure, 
place switch on INT position.
    Add page 8 to Favourites
    image text
    Enable zoom 
    							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
www.addonics.com
Phone:   408-573-8580
Fax:     408-573-8588
Email:   http://www.addonics.com/sales/query/
CONTACT US
    All Addonics Technologies manuals Comments (0)

    Related Manuals for Addonics Technologies Ruby 25 HDDSSD drive kit RDCSSAESU user guide