Addonics Technologies Ruby 25 HDDSSD drive kit RDCSSAESU user guide

T E C H N O L O G I E S
User Guide
Ruby Drive Cartridge System
(RDCSSAES / RDCSSAEU)
www.addonics.com
www.addonics.com
Technical Support
If you need any assistance to get your unit functioning properly, please have your 
product information ready and contact Addonics Technical Support at:
Hours: 8:30 am - 6:00 pm PST
Phone: 408-453-6212
Email: http://www.addonics.com/support/query/
v7.1.11                 

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Enclosure Overview
Step 1
Separate the top from the bottom cover of the drive enclosure by loosening the 
screw.
Step 2
Align the SATA connector in the 2.5” hard drive with the SATA connector on the PCB.
Step 3
Wrap the shock absorbers around the hard drive and PCB.
Top Cover
Bottom Cover
PCB
Shock Absorbers         

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Step 4
Turn over the PCB and secure the hard drive to the PCB with the mounting \
screws 
that come with the kit.
Step 5
Mount the board to the bottom cover.
Step 6
Put the top cover on by holding it in near vertical position and sliding\
 the two metal 
clips inside the two small slots on the rear of the bottom cover.
Step 7
Lower the front of the top cover and making sure the two...

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Ruby Enclosure
Switch:
INT: This mode is used when the enclosure is placed inside a drive cradle. Fo\
r 
drive cartridge system kits, this is the mode used.
EXT:  This mode is used if the enclosure is used as an external hard drive.
Ruby Drive Cradle
Note:  You can only use one power connector at a time. Either use the 4-pin 
Molex or 15-pin SATA connector but do not simultaneously...

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Model: RDCSSAES
*Note: The Ruby Drive Cartridge System with the SATA interface must be connected 
to a SATA controller with hot swap capability in order to add and remove drive 
cartridge without rebooting. Please consult your motherboard or the add-\
in card 
manufacturer to determine hot swap support on your SATA controller. All of the 
Addonics SATA Host Controllers are hot swap...

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Model: RDCSSAEU
This Ruby model will hot-swap.
Step 1
Connect the SATA to USB2.0 converter to the SATA interface of the cradle. 
Step 2
Connect the Y-cable that came with converter to the 4-pin floppy connector on 
the converter. The other end would connect to your system’s power supply. This 
power connection provides power to both converter and the ruby drive car\
tridge 
system....

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Step 3
For data connection, you can either use the USB pin header cable to 
connect from the pin-header type USB connector on the converter to the 
USB pin-header on the motherboard. Or connect to the USB B type male 
connector on the converter to an internal USB port.
Step 4
Slide the Ruby enclosure inside the cradle. To turn ON the drive enclosure, 
place switch on INT position. 

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
www.addonics.com
Phone:   408-573-8580
Fax:     408-573-8588
Email:   http://www.addonics.com/sales/query/
CONTACT US