Adam Equipment PTM Drum and Wheelchair Scale GKREVL1 User Manual

							 
39                              © Adam Equipment Company 2013 
 
CALIBRATION 
·  The  GK  indicator  can  be  calibrated  using  kilogram  w eights  or  using 
pounds weights, depending on the weighing unit sele cted at the time of 
calibration. 
  ·   To  start  the  calibration,  either  get  into  the  calib ration  section  through 
the  Indicator  Settings  ( “FUnC 3”-  see  Section  13.3)  or  turn  the  indicator 
off and switch on again and then press  [Tare] during the self-test.  Enter 
code  number  0000  and  press  [Tare].  This  will  take  you  directly  to  the 
calibration section. 
 
·  The display will show  "UnLoAd"  
 
·  Remove  all  weight  from  the  platform  and  then  press  the [Tare]   key 
when  the  display  is  stable.  After  the  Zero  point  is   set,  the  display  will 
show  “Ld  xx” . Place the suggested calibration mass on the platf orm. It is 
best  to  use  a  weight  close  to  the  full  capacity  of  the  indicator.    If  the 
mass  is  different  from  the  displayed  value,  enter  t he  value  of  the  mass 
in whole numbers. The kg or the lb symbol will be o n to show the active 
unit. 
 
·  Press the  [Tare] key when the stable indicator is on.   
 
·  The  indicator  will  calibrate  to  the  mass.  When  comp lete,  it  will  display 
“PASS”  and  then  either  display  “S8    CAL”  (if  entered  the  calibration 
section  through  the  Indicator  Settings  as  per  secti on  13.3)  or  return  to 
normal weighing (if entered directly). Remove the c alibration mass. 
 
·  If an error message  “FAIL H” or “FAIL L”  is shown, re-check the calibration 
and repeat. If the error cannot be corrected contac t your supplier.  
						

							 
40                              © Adam Equipment Company 2013 
PARAMETER SETTINGS 
Pressing the [Func] key allows the user to access the parameters for cu stomising the 
indicator. The parameters are split into 4 groups-   
  
1. Check weighing parameters,  
2. RS-232 parameters  
3. Indicator parameters 
4. Percent and Animal Weighing Functions  
·  When  [Func]  is  pressed,  display  will  first  show   “FUnC  1” for  Check  weighing 
parameters.  
 
·  Enter  [2]  for  RS-232  parameters  or   [3]  for  Indicator  parameters  or  [4] for 
percent  weighing  and  animal  weighing,      or    press  t he [Func]   key  to  advance 
through  the  groups  “FUnC 1”, “FUnC 2”  , “FUnC 3”  and “FUnC 4” .  Press [Tare] to 
enter the desired group of parameters.  
 
·  Press  [Zero]  to  return  to  the  group  “FUnC  1”.  If  you  press  [Zero]  again,  the 
indicator will exit the User Parameter section and  return to normal weighing. 
  
1.13.   CHECK WEIGHING PARAMETERS 
 
·  Shortcut to enter this group is to press and hold t he  [Unit]  key for 4 seconds. 
The display will go directly to  “FUnC 1”.  
 
·  Press  [Tare]  to enter the group.  
 
·  Press   [Func]  to  scroll  through  the  parameters  and  press  [Tare] to  enter  a 
parameter setting.  
  
						

							 
41                              © Adam Equipment Company 2013 
·  Press  [Func]  to view the options for setting.  
 
·  Press   [Tare]  to  confirm  the  change  and  then  advance  to  the  next  parameter 
by pressing the  [Func] key. 
  
This group of parameters- 
-   enables or disables the percent weighing  
-   sets the lock for re-setting the check weighing  limits 
-   enables or disables the check weighing LED indi cator 
-   enables or disables the check weighing alarm  
-   sets the User Password for check weighing  
   enables or disables the negative check weighing 
Parameter  Description  Options  Default  
setting 
F1  LLk  This parameter prevents the  
normal user from changing  
the limits with the help of a  
Limit Lock.
 
  With LLK set to Off (oFF),  
the user is allowed to  
change limits at any  
time.    
With LLK set to Preset  
(PSt), the user is allowed 
to use one of the preset  
limits only.   oFF  
						

							 
42                              © Adam Equipment Company 2013 
  
F2  LEd This parameter sets the LED  
indicator to off or on and the 
LED type (whether LED’s are 
on in the form of a  
continuous bar or a spot LED  
or a segment of colour).
 bAr
    -  Bar type  
Spot   - Spot type  
Seg   
-   Segment  
oFF      -  Off 
  bAr
 
F3  bEP  This parameter sets the  
Beeper to off or on. If set to 
on, the beeper can further 
be set to sound when the  
weighing result is within or  
outside the check-weighing  
limits.
  bP oFF
  - Off  
bP inL    - Within limits  
bP otL  - Outside limits 
(>20d)    bP inL
 
F4  CPS  This parameter allows  
setting of a new Check 
weighing password, must be  
entered twice when asked.  
When complete, it will  
display 
“donE”.  To be entered manually.   
0000  
F5  nCK  This parameter enables  
negative check weighing  
function with ability to do  
negative tare.
  on  
oFF    
on 
NOTE:    
1.   The  Check  weighing  password  is  separate  from  the  in dicator  password,  see 
section 13.3. 
  
2.   If  the  password  is  other  than  0000,  user  must  enter   the  password  to  gain 
access to  “F3 LLk”, “F4 LEd” , “F5 bEP” , “F6  CPS”  and “F7  nCK” .   
						

							 
43                              © Adam Equipment Company 2013 
  
1.14.  RS-232 PARAMETERS 
 
·  Shortcut to enter this group is to press and hold t he [Print]  key for 4 seconds. 
The display will go directly to  “C1   on”.  
 
·  Press  [Func]  to view the list of parameters.  
 
·  Press  [Tare]  to  enter  a  parameter.  Press   [Func] to  view  the  options  for  the 
parameter settings.  
 
·  Press  [Tare]  to  confirm  the  change  and  then  advance  to  the  next  parameter 
by pressing the  [Func] key. 
 
·  Press  [Zero]  to  return  to  the  group  “FUnC  2”.  If  you  press   [Zero] again,  the 
indicator will exit the User Parameter section and  return to weighing. 
  
This group of parameters can be set by the user for  setting the language, baud rate, 
printing mode, etc.  The user can also set a Scale  ID number and a User ID number.   
 
Parameter  Description  Options  Default  Values  or  setting 
C1  on Enable or disable the RS- 
232 interface Prt on   
Prt oFF  Prt on 
C2  bd 
Baud Rate     600  
1200 
2400  
4800  
9600   
19200   9600  
						

							 
44                              © Adam Equipment Company 2013 
  
C3 PrM 
Printing Mode- Manual as  
soon as stable,   
Manual as soon as the key  
is pressed stable or not,   
Automatic As soon as  
stable  
Automatic when weight is  
removed  
Continuous only when  
stable  
Continuous at any time,  
stable or not  mA  StA   
*mA  AnY  
*Au  StA  
Au End   
*Ct StA  
*Ct Any  
*Not an option on  
EC approved scales 
 
mA Sta  
C3 PrM Printing Mode- Manual,  
Continuous or Automatic mAn,  
Cont 
(not on EC approved 
scales) 
AUto     mAn
 
C4 Aon Enable or disable the  
Accumulation  AC on   
AC oFF   AC on
 
C5 Ln 
Select Language EnGLi (English)  
 FrEnCH 
(French) 
GErmAn (German)     
SPAn 
(Spanish)  EnGLi 
 
C6  UId 
Set User ID  To be entered manually 000000 
C7   Sid 
Set Scale ID  To be entered manually 000000 
C8   Lab 
Set the print format to be  
a label as shown (ON) or a  
single line (Off) Lab On  
Lab Off
 
Lab On 
    
						

							 
45                              © Adam Equipment Company 2013 
  
The  indicator  will  perform  the  following,  depending   on  the  Accumulation  and  Print 
Settings: 
 
ACCUMULATION  SETTINGS
 
PRINT SETTINGS 
AC on AC Off 
mA StA 
 
Accumulate and Print as soon  
as  the   [Print] key is pressed. 
 
If the  [Print]  key is pressed a 
second time print only,  
accumulation will only occur  
if scale returns to zero first.  Print as soon as the 
[Print] key is 
pressed, and the scale is stable.  
Do not accumulate. 
mA Any 
Not  available  on  
approved indicators 
Accumulate and Print as soon  
as  the   [Print] key is pressed. 
Even if the scale is unstable.   
If the   [Print]  key is pressed a 
second time print only,  
accumulation will only occur 
if scale returns to zero first.  Print as soon as the 
[Print] key is 
pressed, Stable or not.  
Do not accumulate. 
Au StA  
Not  available  on  
approved indicators 
Accumulate and print  
automatically as soon as  
scale becomes stable.   
If the scale goes unstable and  
then stable again print the 
new stable value. But do not  
add to Accumulation.  
If the   [Print]  key is pressed 
at any time the scale is stable   
print only.  
Accumulation will only occur  
if scale returns to zero first.    Print as soon as the scale is stable. 
If the scale goes unstable and then  
stable again print the new stable  
value.   
If the 
 [Print]  key is pressed  print 
again. 
Do not accumulate.  
						

							 
46                              © Adam Equipment Company 2013 
Au End  
 
Accumulate and print when  
the scale has reached  
stability after  the weight is  
removed.   
If the   [Print]  key is pressed it 
is ignored.    Print after the scale is stable and the  
weight has been removed.  
If the 
 [Print]  key is pressed it is 
ignored.   
Do not accumulate. 
Ct StA 
Not  available  on  
approved indicators 
Print continuously if the scale  
is stable.  
Accumulate immediately  
when  [Print]  key is pressed if 
the scale is stable.  Print continuously if the scale is 
stable.  
Do not accumulate. 
Ct AnY 
Not  available  on  
approved indicators 
Print continuously, stable or  
not.  
Accumulate when the  [Print] 
key is pressed stable or not.  Print continuously stable or not.  
Do not accumulate. 
    
Note: Manual Printing is allowed at zero only when 
the scale is stable.  If set to Auto 
the scale will not automatically print when it retu rns to zero.  
On EC approved scales printing is not allowed less  than 20 divisions. 
Accumulation is only allowed if the weight is great er than 20 divisions. 
  
						

							 
47                              © Adam Equipment Company 2013 
1.15.  INDICATOR PARAMETERS  
 
·  Shortcut  to  enter  this  group  is  to  press  and  hold  t he  [Count]   Key  for  4 
seconds. The display will go directly to “S1    Un   ”.  
·   Press  [Func]  to view the list of parameters.  
·   Press  [Tare]  to  enter  a  parameter.  Press  [Func] to  view  the  options  for  the 
parameter settings.  
·   Press  [Tare]   to  confirm  the  change  and  then  advance  to  the  next   parameter 
by pressing the  [Func] key. 
·   Press  [Zero]  to  return  to  the  group  “FUnC  3”.  If  you  press  [Zero] again,  the 
indicator will exit the User Parameter section and  return to normal weighing. 
  
This group of parameters are used to control the op eration of the indicator.   
 Parameter  Description  Options  Default   
setting 
S1  Un  Enable or disable weighing  
units, Not all units are 
available for all scales 
settings.   
Only USA scales have  
imperial unit. 
  kg  
g  
lb  
oz 
lb:oz
  kg   
 
S2  bL  Backlight set to always on,  
always off or automatic on 
whenever a weight is  
placed or a key is pressed  EL   oFF
  
EL   on   
EL   AU  EL   AU
 
  
						

							 
48                              © Adam Equipment Company 2013 
 
S3  AoF  Auto Off- Disable or set  
time increment to turn off  
the indicator  SLP   0  
SLP   1  
SLP   5 
SLP   10
  SLP   0   
S4   dt  Set Time and Date format  
and settings  Enter the time  
manually  
Enter the date  
manually
  00:00:00  
mm:dd:yy
 
S5  diS  Display all weights or only  
when stable    ALL 
StAb   ALL 
 
S6  Fi  Filter setting to slow,  
normal or fast  SLow  
nor  
FASt
  nor   
S7 SPS  Scale Password- If it is  
anything other than 0000 
then the user must enter  
the password to gain  
access to any of the 
indicator parameter 
settings. Must be entered 
twice when asked. When  
complete, it will display  
“donE”
.  PI _ _ _ _   
0000 
S8 CAL  Calibration 
Calibrate the indicator  
to a platform. See 
Section 10.0 
 -