Adam Equipment Eclipse Precision Balances ECLIPSEEBL User Manual
Here you can view all the pages of manual Adam Equipment Eclipse Precision Balances ECLIPSEEBL User Manual. The Adam Equipment manuals for Balance are available online for free. You can easily download all the documents as PDF.
Page 21
![Page 21
EN
© Adam Equipment Company 2015 19 3016612482 Rev1-Aug15
When the display shows zero, place the item to be weighed. Only the net weight will be
displayed.
When a tared weight has been stored, pressing [ 0/T ]
again will remove it .
The [Print] key is lit, indicating that print output to a connected device is available. Print
output will always be the net weight shown on screen, and in the current weighing unit
selected.
At any time the [Unit] key may be pressed to...](http://img.usermanuals.tech/thumb/168/2133/w300_eclipse-precision-balances-eclipseebl-1478547370_d-20.png "Page 21
EN
© Adam Equipment Company 2015 19 3016612482 Rev1-Aug15
When the display shows zero, place the item to be weighed. Only the net weight will be
displayed.
When a tared weight has been stored, pressing [ 0/T ]
again will remove it .
The [Print] key is lit, indicating that print output to a connected device is available. Print
output will always be the net weight shown on screen, and in the current weighing unit
selected.
At any time the [Unit] key may be pressed to...")
EN © Adam Equipment Company 2015 19 3016612482 Rev1-Aug15 When the display shows zero, place the item to be weighed. Only the net weight will be displayed. When a tared weight has been stored, pressing [ 0/T ] again will remove it . The [Print] key is lit, indicating that print output to a connected device is available. Print output will always be the net weight shown on screen, and in the current weighing unit selected. At any time the [Unit] key may be pressed to...
Page 22
EN © Adam Equipment Company 2015 20 3016612482 Rev1-Aug15 The balance displays the alternate weighing units with as much precision as possible. For example, the EBL 423 balances (420g x 0.001g) could weigh up to: Unit Maximum d = g 420 0.001 mg 420000 1 kg 0.420000 0.000001 ct. 2100.000 0.005 dwt 270.0662 0.001 GN 6481.591 0.02 ozt 13.503314 0.00005 oz 14.815064 0.00005 lb 0.925940 0.00001 dr 237.041037 0.001 tl.H 11.111297 0.00005 tl.T 11.200015 0.00005 tl.S 11.111295...
Page 23
EN © Adam Equipment Company 2015 21 3016612482 Rev1-Aug15 10.4 FUNCTIONS When weighing, the user can access the applications that have been enabled (see section 13.2.). The following applications are available: · Weighing · Parts counting · Percent weighing · Check weighing · Animal (Dynamic) weighing · Net/Total & Accumulation · Density determination (Liquid & Solid) The selectable functions can be enabled in supervisor mode and are selected by pressing the...
Page 24
![Page 24
EN
© Adam Equipment Company 2015 22 3016612482 Rev1-Aug15
10.4.1 Parts Counting
This allows the user to weigh a sample of parts to compute an average unit weight and
then determine the number of items being weighed by dividing the net weight by the unit
weight value. The result is always a whole number of parts.
The balance will have a pre-set number of parts to be used as a sample. These values are
10, 25 , 50 or 100 items.
Press [Mode] and cycle through the available...](http://img.usermanuals.tech/thumb/168/2133/w300_eclipse-precision-balances-eclipseebl-1478547370_d-23.png "Page 24
EN
© Adam Equipment Company 2015 22 3016612482 Rev1-Aug15
10.4.1 Parts Counting
This allows the user to weigh a sample of parts to compute an average unit weight and
then determine the number of items being weighed by dividing the net weight by the unit
weight value. The result is always a whole number of parts.
The balance will have a pre-set number of parts to be used as a sample. These values are
10, 25 , 50 or 100 items.
Press [Mode] and cycle through the available...")
EN © Adam Equipment Company 2015 22 3016612482 Rev1-Aug15 10.4.1 Parts Counting This allows the user to weigh a sample of parts to compute an average unit weight and then determine the number of items being weighed by dividing the net weight by the unit weight value. The result is always a whole number of parts. The balance will have a pre-set number of parts to be used as a sample. These values are 10, 25 , 50 or 100 items. Press [Mode] and cycle through the available...
Page 25
![Page 25
EN
© Adam Equipment Company 2015 23 3016612482 Rev1-Aug15
10.4.2 Percentage Weighing
Percent weighing will be done by defining a certain weight to be 100%. The weight to be
used can either be entered by the user or taken from a sample
Press [Mode] and then the [Up] or [Down] key until “
PERCENT
PERCENTPERCENT PERCENT”is displayed. Now enter
percent weighing mode by pressing [Select].
Display will show, “ SAmmPLE
S
AmmPLESAmmPLE
SAmmPLE
%” (sample method) or “ Ent
E nt...](http://img.usermanuals.tech/thumb/168/2133/w300_eclipse-precision-balances-eclipseebl-1478547370_d-24.png "Page 25
EN
© Adam Equipment Company 2015 23 3016612482 Rev1-Aug15
10.4.2 Percentage Weighing
Percent weighing will be done by defining a certain weight to be 100%. The weight to be
used can either be entered by the user or taken from a sample
Press [Mode] and then the [Up] or [Down] key until “
PERCENT
PERCENTPERCENT PERCENT”is displayed. Now enter
percent weighing mode by pressing [Select].
Display will show, “ SAmmPLE
S
AmmPLESAmmPLE
SAmmPLE
%” (sample method) or “ Ent
E nt...")
EN © Adam Equipment Company 2015 23 3016612482 Rev1-Aug15 10.4.2 Percentage Weighing Percent weighing will be done by defining a certain weight to be 100%. The weight to be used can either be entered by the user or taken from a sample Press [Mode] and then the [Up] or [Down] key until “ PERCENT PERCENTPERCENT PERCENT”is displayed. Now enter percent weighing mode by pressing [Select]. Display will show, “ SAmmPLE S AmmPLESAmmPLE SAmmPLE %” (sample method) or “ Ent E nt...
Page 26
EN © Adam Equipment Company 2015 24 3016612482 Rev1-Aug15 10.4.3 Check Weighing During weighing of a sample the balance can be set to show if the weight is above or below an upper and a lower limit. The display will use the arrows under the bar graph to show that check weighing is operating. The bars between the arrows will indicate when the weight is below the lower limit, between the limits or above the upper limit. The buzzer can be set to be active when the weight is...
Page 27
![Page 27
EN
© Adam Equipment Company 2015 25 3016612482 Rev1-Aug15
If buzzer is disabled in the main setup of the balance (see section 13.5) then it remains
disabled. No buzzer settings for check weighing will be shown and the balance is now
ready for check weighing.
If the buzzer is enabled in the main setup of the balance, then next the buzzer setting
options are displayed:
· Press [Up] or [Down] to scroll through the options –
“
BUZZER
BUZZERBUZZER...](http://img.usermanuals.tech/thumb/168/2133/w300_eclipse-precision-balances-eclipseebl-1478547370_d-26.png "Page 27
EN
© Adam Equipment Company 2015 25 3016612482 Rev1-Aug15
If buzzer is disabled in the main setup of the balance (see section 13.5) then it remains
disabled. No buzzer settings for check weighing will be shown and the balance is now
ready for check weighing.
If the buzzer is enabled in the main setup of the balance, then next the buzzer setting
options are displayed:
· Press [Up] or [Down] to scroll through the options –
“
BUZZER
BUZZERBUZZER...")
EN © Adam Equipment Company 2015 25 3016612482 Rev1-Aug15 If buzzer is disabled in the main setup of the balance (see section 13.5) then it remains disabled. No buzzer settings for check weighing will be shown and the balance is now ready for check weighing. If the buzzer is enabled in the main setup of the balance, then next the buzzer setting options are displayed: · Press [Up] or [Down] to scroll through the options – “ BUZZER BUZZERBUZZER...
Page 28
EN © Adam Equipment Company 2015 26 3016612482 Rev1-Aug15 10.4.4 Animal (Dynamic) Weighing The balance can be set to weigh animals or unstable/moving items. This is commonly referred to as ‘Animal’ or ‘Dynamic’ weighing mode. The balance will collect the weight over a period of time to arrive at an average value and display the value until the operator resets the balance. The actual weighing process can begin either automatically when the weight is placed on the pan, or when...
Page 29
![Page 29
EN
© Adam Equipment Company 2015 27 3016612482 Rev1-Aug15
Place the item on the pan. The animal weighing test will begin automatically.
After the pre-configured delay and test time have elapsed (see section 10.4.4.3 on
Dynamic Weighing Setup Parameters), the “
HOLD” symbol and the result will be displayed.
Remove the item from the pan. Press [Mode] to go back to “ rUN
r
UNrUN
rUN
” to weigh another item, or
[ 0/T ]
to return to normal weighing.
10.4.4.3 Animal (Dynamic)...](http://img.usermanuals.tech/thumb/168/2133/w300_eclipse-precision-balances-eclipseebl-1478547370_d-28.png "Page 29
EN
© Adam Equipment Company 2015 27 3016612482 Rev1-Aug15
Place the item on the pan. The animal weighing test will begin automatically.
After the pre-configured delay and test time have elapsed (see section 10.4.4.3 on
Dynamic Weighing Setup Parameters), the “
HOLD” symbol and the result will be displayed.
Remove the item from the pan. Press [Mode] to go back to “ rUN
r
UNrUN
rUN
” to weigh another item, or
[ 0/T ]
to return to normal weighing.
10.4.4.3 Animal (Dynamic)...")
EN © Adam Equipment Company 2015 27 3016612482 Rev1-Aug15 Place the item on the pan. The animal weighing test will begin automatically. After the pre-configured delay and test time have elapsed (see section 10.4.4.3 on Dynamic Weighing Setup Parameters), the “ HOLD” symbol and the result will be displayed. Remove the item from the pan. Press [Mode] to go back to “ rUN r UNrUN rUN ” to weigh another item, or [ 0/T ] to return to normal weighing. 10.4.4.3 Animal (Dynamic)...
Page 30
![Page 30
EN
© Adam Equipment Company 2015 28 3016612482 Rev1-Aug15
selected then it will not be accepted and “ER L\bW
E R L\bWER L\bW
ER L\bW
” or “ER HIGH
E R HIGHER HIGH
ER HIGH
” will be displayed followed
b
y return to the time entry screen again.
To confirm the desired value, press [Select] or to escape without changing the value,
press [Mode].
10.4.4.3.4 Test time “TEST T
T
EST TTEST T
TEST T
”
P
ress [Select] when “TESt t
T
ESt tTESt t
TESt t
” is shown and the display will...](http://img.usermanuals.tech/thumb/168/2133/w300_eclipse-precision-balances-eclipseebl-1478547370_d-29.png "Page 30
EN
© Adam Equipment Company 2015 28 3016612482 Rev1-Aug15
selected then it will not be accepted and “ER L\bW
E R L\bWER L\bW
ER L\bW
” or “ER HIGH
E R HIGHER HIGH
ER HIGH
” will be displayed followed
b
y return to the time entry screen again.
To confirm the desired value, press [Select] or to escape without changing the value,
press [Mode].
10.4.4.3.4 Test time “TEST T
T
EST TTEST T
TEST T
”
P
ress [Select] when “TESt t
T
ESt tTESt t
TESt t
” is shown and the display will...")
EN © Adam Equipment Company 2015 28 3016612482 Rev1-Aug15 selected then it will not be accepted and “ER L\bW E R L\bWER L\bW ER L\bW ” or “ER HIGH E R HIGHER HIGH ER HIGH ” will be displayed followed b y return to the time entry screen again. To confirm the desired value, press [Select] or to escape without changing the value, press [Mode]. 10.4.4.3.4 Test time “TEST T T EST TTEST T TEST T ” P ress [Select] when “TESt t T ESt tTESt t TESt t ” is shown and the display will...