Acer Aspire One Model Nav Service Guide
Here you can view all the pages of manual Acer Aspire One Model Nav Service Guide. The Acer manuals for Notebook are available online for free. You can easily download all the documents as PDF.
Page 51
Chapter 341 External Module Disassembly Process NOTE: The product previews seen in the disassembly procedures may not represent the final product color or configuration. External Modules Disassembly Flowchart Screw List StepScrewQuantityPart No. HDD Door M2*4 3 86.SAS02.002 HDD Carrier M3*3 4 86.SAS02.006 WLAN Module M2*3 1 86.SAS02.001 DIMM Door M2*6 1 86.SAS02.004 Back Cover M2*3 286.SAS02.001 M2*4 5 86.SAS02.002 M2*6 4 86.SAS02.004 Disconnect power and signal cables from system Remove Battery Turn...
Page 52
42Chapter 3 Removing the Battery Pack 1.Turn the computer over. 2.Slide the battery lock/unlock latch to the unlock position. 3.Slide and hold the battery release latch to the release position (1), then slide out the battery pack from the main unit (2). 1 2
Page 53
Chapter 343 Removing the HDD Module 1.Remove the three (3) screws from the HDD Cover. 2.Lift the HDD cover up to remove. StepSizeQuantityScrew Type HDD Cover M2*4 3
Page 54
44Chapter 3 3.Slide the HDD in the direction of the arrow to disconnect the HDD from the interface connector. 4.Lift the hard disk drive module out of the bay. NOTE: To prevent damage to the device, avoid pressing down on it or placing heavy objects on top of it. 5.Remove the four (4) screws (two each side) securing the hard disk to the carrier. 6.Remove the HDD from the carrier. StepSizeQuantityScrew Type HDD Carrier M3*3 4
Page 55
Chapter 345 Removing the DIMM Module 1.Remove one (1) screw from the DIMM door. 2.Insert a plastic tool to lift the corner of the DIMM cover. 3.Lift the DIMM cover clear of the device.
Page 56
46Chapter 3 4.Push out the release latches on both sides of the DIMM socket to release the DIMM module. 5.Remove the DIMM module.
Page 57
Chapter 347 Removing the WLAN Module 1.See “Removing the HDD Module” on page 43. 2.Disconnect the Antenna cables from the WLAN Module. 3.Move the antenna away and remove the one (1) screw from the WLAN Module. StepSizeQuantityScrew Type WLAN Module M2*3 1
Page 58
48Chapter 3 4.Pull the WLAN Module from the slot. NOTE: When reattaching the antennas, ensure the cables are tucked into the chassis to prevent damage.
Page 59
Chapter 349 Removing the Back Cover 1.See “Removing the HDD Module” on page 43. 2.See “Removing the DIMM Module” on page 45. 3.See “Removing the WLAN Module” on page 47. 4.Remove eleven (11) screws from the Back Cover. StepSizeQuantityScrew Type Back Cover (Green Callout)M2*3 2 Back Cover (Red Callout)M2*4 5 Back Cover (Yellow Callout)M2*6 4
Page 60
50Chapter 3 Main Unit Disassembly Process IMPORTANT: Cable paths and positioning may not represent the actual model. During the removal and replacement of components, ensure all available cable channels and clips are used and that the cables are replaced in the same position. NOTE: The product previews seen in the disassembly procedures may not represent the final product color or configuration. Main Unit Disassembly Flowchart Screw List StepScrewQuantityPart No. Upper Cover M2*6 7 86.SAS02.004 LED...