Acer Aspire 6530 Service Guide

							Chapter 371
Removing the Finger Print Reader
1.Remove the Upper Base. See “Removing the Upper Base” on page 68.
2.Unlock the securing latch and disconnect the Touch Pad FFC.
3.Unlock the securing latch and disconnect the Finger Print Reader FFC.
4.Remove the three securing screws.
StepSizeQuantityScrew Type
Finger Print 
ReaderM2.0*3.0-I-NI-NYLOK 3 
						

							72Chapter 3
5.Using your fingers, gently lift the Finger Print Reader board from the Upper Base.
Removing the USB Board
1.Remove the Upper Base. See “Removing the Upper Base” on page 68.
2.Grasp the cable connector and pull to remove from the bottom base.
3.Remove the single securing screw from the USB board.
StepSizeQuantityScrew Type
USB Board M2.0*3.0-I (BKAG) 
(NYLOK) IRON1 
						

							Chapter 373
4.Hold the USB board by the edges and pull up to remove.
Removing the Modem Module
1.Remove the Upper Base. See “Removing the Upper Base” on page 68.
2.Disconnect the RJ-11 cable from the modem as shown.
3.Remove the two (2) securing screws.
StepSizeQuantityScrew Type
Modem Module M2.0*3.0-I-NI-NYLOK 2 
						

							74Chapter 3
4.Lift the module and remove from the lower cover as shown.
Removing the Bluetooth Module
1.Remove the Modem Module. See “Removing the Modem Module” on page 73.
2. Grasp the cable as shown and pull to disconnect from the Bluetooth module.
3. Remove the single securing screw.
StepSizeQuantityScrew Type
Bluetooth Module M2 .0*3.0-I-NI-NYLOK 1 
						

							Chapter 375
4.Grasp the module by the right side and lift up to remove. 
						

							76Chapter 3
Removing the Mainboard
1.Remove the LCD Module. See “Removing the LCD Module” on page 67.
2.Remove the Upper Base. See “Removing the Upper Base” on page 68.
3.Remove the See “Removing the Modem Module” on page 73.
4.Remove the Bluetooth Module. See “Removing the Bluetooth Module” on page 74.
5.Disconnect the USB and Bluetooth cables remaining on the mainboard.
6.Grasp the RJ-11 cable and remove it from the mainboard cable notch as shown.
7.Disconnect the Subwoofer cable attached to the mainboard.
  
						

							Chapter 377
8.Remove the three securing screws.
9.While holding the left side of the Lower Base, lift and pivot the mainboard to remove from the base.
10.Grasp the mainboard by both sides and pivot upwards to remove.
StepSizeQuantityScrew Type
Mainboard M2.5*4.0-I 
(NI)(NYLOK)3 
						

							78Chapter 3
Removing the Thermal Module
1.Remove the Mainboard. See “Removing the Mainboard” on page 76.
2.Turn the Mainboard over and place on a clean surface.
3.Hold the cable connector and lift to disconnect from the mainboard.
4.Remove the two securing screws (red) and loosen the three captive screws (blue) found on the Thermal 
Module.
StepSizeQuantityScrew Type
CPU Thermal 
Module
(red call out)M2.5*4.0-I 
(NI)(NYLOK)2 
						

							Chapter 379
WARNING:To prevent damage to the Thermal Module or the CPU, hold and lift the Thermal Module by lifting 
both ends up and away at the same time.
5.Hold the module on both sides and lift it clear of the Mainboard. 
Removing the CPU 
1.Remove the Thermal Module. See “Removing the Thermal Module” on page 78.
2.Using a flat screwdriver, turn the CPU socket latch counter-clockwise 180° to release the CPU.
3.Lift the CPU clear of the Mainboard. 
						

							80Chapter 3
 LCD Module Disassembly Process
LCD Module Disassembly Flowchart
Screw List
StepScrewQuantityPart No.
LCD Bezel M2.5*6.5-I 
(BZN(NYLOK-RED)10 86.ARE07.001
LCD Panel M2.5*2.5-I 
(NI)(NYLOK)6 86.T25V7.010
LCD Brackets M2.0*3.0-I (BKAG) 
(NYLOK) IRON8 86.ARE07.002
Rem ove
Inverter BoardRem ove
LCD Panel
Rem ove
LCD Bezel
Rem ove
LCD FPC Cable
Rem ove
Camera Module
Remove LCD
Panel from  Main
Unit before
proceeding
Rem ove
LCD Brackets
Rem ove
LCD Assembly
LCD
AssemblyBack
Panel
Assembly