Acer Aspire 6530 Service Guide

							Chapter 341
Machine Disassembly and Replacement
This chapter contains step-by-step procedures on how to disassemble the notebook computer for 
maintenance and troubleshooting.
Disassembly Requirements
To disassemble the computer, you need the following tools:
•Wrist grounding strap and conductive mat for preventing electrostatic discharge
•Flat screwdriver
•Philips screwdriver
•Plastic flat screwdriver
•Plastic tweezers
NOTE: The screws for the different components vary in size. During the disassembly process, group the 
screws with the corresponding components to avoid mismatch when putting back the components.
Chapter 3 
						

							42Chapter 3
General Information
Pre-disassembly Instructions
Before proceeding with the disassembly procedure, make sure that you do the following:
1.Turn off the power to the system and all peripherals.
2.Unplug the AC adapter and all power and signal cables from the system. 
3.Place the system on a flat, stable surface. 
4.Remove the battery pack.
Disassembly Process
The disassembly process is divided into the following stages:
•External module disassembly
•Main unit disassembly
•LCD module disassembly
The flowcharts provided in the succeeding disassembly sections illustrate the entire disassembly sequence. 
Observe the order of the sequence to avoid damage to any of the hardware components. For example, if you 
want to remove the main board, you must first remove the keyboard, then disassemble the inside assembly 
frame in that order.
Main Screw List 
ScrewQuantityPart Number
M2.5*6.5-I (BZN(NYLOK-RED)) 42 86.ARE07.001
M2.0*3.0-I (BKAG)(NYLOK) IRON 10 86.ARE07.002
M2.0*3.0-I-NI-NYLOK 13 86.A08V7.005
M3*0.5+3.5I 8 86.TDY07.003
M2.5*2.5-I (NI)(NYLOK) 6 86.T25V7.010
M2.5*4.0-I (NI)(NYLOK) 7 86.D01V7.001
M2.5*5-I (BNI)(NYLOK) 4 86.A03V7.003
M2.5*8-I BNI NYLOK 4 86.T48V7.001 
						

							Chapter 343
External Module Disassembly Process
External Modules Disassembly Flowchart
The flowchart below gives you a graphic representation on the entire disassembly sequence and instructs you 
on the components that need to be removed during servicing. For example, if you want to remove the main 
board, you must first remove the keyboard, then disassemble the inside assembly frame in that order.
Screw List
StepScrewQuantityPart No.
VGA Module M2.5*8-I BNI NYLOK 4 86.T48V7.001
TV Tuner M2.0*3.0-I (BKAG) 
(NYLOK) IRON2 86.ARE07.002
WLAN Module M2.0*3.0-I-NI-NYLOK  2 86.A08V7.005
Main HDD Carrier M3*0.5+3.5I 4 86.TDY07.003
ODD Module M2.5*6.5-I 
(BZN(NYLOK-RED)1 86.ARE07.001
ODD Bracket M2.0*3.0-I (BKAG) 
(NYLOK) IRON2 86.ARE07.002
HDD2 Module M2.0*3.0-I (BKAG) 
(NYLOK) IRON2 86.ARE07.002
HDD2 Carrier M3*0.5+3.5I 4 86.TDY07.003
Rem ove
Lower Covers
Rem ove
NewCard
Dummy
Disconnect pow er
and signal cables
from system
Rem ove
Battery
Turn off system
and peripherals
pow er
Rem ove
DIMMs
Rem ove
SD Dummy
Rem ove
HDDRem ove
ODD
Rem ove
WLAN
Rem ove
VGA ModuleRem ove
TV Tu nerRem ove
HDD2 
						

							44Chapter 3
Removing the Battery Pack
1.Turn computer over. 
2.Slide the battery lock/unlock latch to the unlock position. 
3.Slide and hold the battery release latch to the release position (1), then slide out the battery pack from the main 
unit (2). 
1
2 
						

							Chapter 345
Removing the SD dummy card
1.Push the SD dummy card all the way in to eject it.
2.Pull it out from the slot.  
						

							46Chapter 3
Removing the ExpressCard dummy card
1.Push the ExpressCard all the way in to eject the ExpressCard dummy. 
2.Pull it out from the slot. 
						

							Chapter 347
Removing the Lower Covers
1.See “Removing the Battery Pack” on page 44.
2.See “Removing the SD dummy card” on page 45.
3.See “Removing the ExpressCard dummy card” on page 46.
4.Loosen the captive screws in the covers as shown.
   
5.Carefully open the Lower Cover. 
6.Remove the HDD2 Cover as shown. 
HDD2 
Cover
Lower 
Cover 
						

							48Chapter 3
Removing the DIMM Modules
1.See “Removing the Battery Pack” on page 44.
2.Remove the Lower Cover See “Removing the Lower Covers” on page 47.
3.Push out the release latches on both sides of the DIMM socket to release the DIMM module. 
4.Remove the DIMM module. 
5.Repeat steps for the second DIMM module. 
						

							Chapter 349
Removing the VGA Module
1.Remove Lower Cover. See “Removing the Lower Covers” on page 47.
2.Remove the four securing screws from the VGA Module.
3.Grasp the VGA module and pull to remove.
StepSizeQuantityScrew Type
VGA Module M2.5*8-I BNI NYLOK 4 
						

							50Chapter 3
Removing the TV Tuner Module
1.See “Removing the Battery Pack” on page 44.
2.Remove the Lower cover. See “Removing the Lower Covers” on page 47.
3.Disconnect the antenna cable from the TV Tuner board as shown.
NOTE:  To ensure proper assembly, the antenna cable must be installed as shown.
4.Move the antenna cables away and remove the two screws to release the TV Tuner module and bracket 
assembly. 
 
StepSizeQuantityScrew Type
TV Tuner Module M2.0*3.0-I-NI-NYLOK 2