Home > 3M > Projector > 3M Super Close Projection System SCP715/SCP740/SCP717 Operators Guide

3M Super Close Projection System SCP715/SCP740/SCP717 Operators Guide

    Download as PDF Print this page Share this page

    Have a look at the manual 3M Super Close Projection System SCP715/SCP740/SCP717 Operators Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 307 3M manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							
    36  © 3M 2008.  All Rights Reserved.
    
    User Controls  3M™ Super Close Projection System
    
     •  “Frequency”, “Phase”, “H Position” and “V Position” functions are only supported under Computer mode.
     Sharpness
    Adjust the sharpness of the image.
     Press the  to decrease the sharpness.
     Press the  to increase the sharpness.
      Frequency
    “Frequency” changes the display data frequency to match the 
    frequency of your computer’s graphic card. If you experience a 
    vertical flickering bar, use this function to make an adjustment.
     Phase
    Change the display data frequency to match the frequency of your 
    computer’s graphic card. When you experience a vertical flickering 
    bar, use this function to make an adjustment.
     H Position (Horizontal Position)
     Press the  to move the image left.
     Press the  to move the image right.
     V Position (Vertical Position)
     Press the  to move the image down.
     Press the  to move the image up. 
    						
    							
    © 3M 2008.  All Rights Reserved.  37
    
    3M™ Super Close Projection System User Controls
    
     DHCP
    On:   
    Assign an IP address to the projector from the DHCP server 
    automatically.
     Off: Assign an IP address manually. 
     IP Address
    Select an IP address.
     Subnet Mask
    Select subnet mask number.
     Gateway
    Select the default gateway of the network connected to the 
    projector.
     DNS
    Select DNS number.
     Apply
    Press “Yes” to apply the selection.
     Status
    To display network information.
    LAN  
    						
    							
    38  © 3M 2008.  All Rights Reserved.
    
    User Controls  3M™ Super Close Projection System
    
    1.  Fill  in  a  new  IP,  a  subnet  mask,  a  gateway  and  a  DNS  in  the  dia-
    logue box.
    2.  
    Then  choose  apply  and  press  “Enter”  button  to  effectuate  the  con-
    figuration process.
    3.   Open  your  web  browser  and  type  in  from  the  OSD  LAN  screen 
    then the web page will display as below:
    4.  Open “Control Panel” to control your projector. 
     
    How to use web browser to control your projector
     •  When you used the projector IP address, you will not be able to link to your service server.      
    						
    							
    © 3M 2008.  All Rights Reserved.  39
    
    3M™ Super Close Projection System User Controls
    
    For example:  
    Use Microsoft Internet Explorer (IE) web browser to control the projec\
    -
    tor, the IP address is http://10.0.50.100.
    Step 1:  Find an IP Address (10.0.50.100) from LAN function of 
    projector.
    Step 2:   Select apply and press 
    “Enter” button to submit function or 
    press “menu” key to exit.
    Step 3:   
    To open Network Connections, click Start, click Control 
    Panel, click Network and Internet Connections, and then 
    click Network Connections. Click the connection you want 
    to configure, and then, under Network Tasks  , click 
    Change settings of this 
    connection.
    Step 4:   On the General tab, under 
    This connection uses the 
    following items, click Inter-
    net Protocol (TCP/IP), and 
    then click “Properties.”
    Step 5:  Click Use the following IP 
    address, and type in as 
    below:
    1) IP address: 10.0.50.XXX 
    2) Subnet mask: 255.255.0.0
    3)  Default gateway: 
    10.0.50.254
    Step 6:    To open Internet Options, 
    click IE web browser, click 
    Internet Options, click the 
    Connections tab and click 
    “LAN Settings...” 
            
    						
    							
    40  © 3M 2008.  All Rights Reserved.
    
    User Controls  3M™ Super Close Projection System
    
    Step 7:  
    The Local Area Network (LAN) 
    Setting dialog box appears, In 
    the Proxy Server area, cancel 
    the Use a proxy server for your 
    LAN check box., then click “OK” 
    button twice.
    Step 8:   Open your IE and type in the IP address of 10.0.50.100 in 
    the URL then press “Enter” key. The web page will display 
    as below:
    Step 9:  Open “Control Panel” to control your projector.       
    						
    							
    © 3M 2008.  All Rights Reserved.  41
    
    3M™ Super Close Projection System User Controls
    
     Security Enable
    On:   Choose “On” to enable security verification when turning on 
    the projector.
     Off:  
    Choose “Off” to be able to switch on the projector without 
    password verification.
     Security Timer
    The function can be selected the time (month/day/hour) to set the number of hours the projector can be used. Once this time has elapsed you will be requested to enter your password again. (Use number buttons on remote. To change password, follow change 
    password security code.)
     Change Security Code
    ■ First Time:
    1.   Press the 
     to set password.
    2.   The Password is 4 digits, DEFAULT VALUE is “0000”. (first 
    time)
    3.   Use 
    number buttons on the remote to select your password, 
    and then press “Enter” key to confirm your selection.
    Security   
    						
    							
    42  © 3M 2008.  All Rights Reserved.
    
    User Controls  3M™ Super Close Projection System
     Change Password:
    1. Press “Enter” to input old password.
    2.  Use number button to enter current password, and then 
    press “Enter” to confirm.
    3.  Enter new password (4 digits in length) using the number 
    buttons on the remote, then press “Enter” to confirm.
    4.  Enter new password again and press “Enter” to confirm. 
    						
    							
    © 3M 2008.  All Rights Reserved.  43
    
    3M™ Super Close Projection System Appendices
    Problem: No image appears on screen
     Ensure all the cables and power connections are correctly and 
    securely connected as described in the “Installation” section.
     Ensure the pins of connectors are not crooked or broken.
     Check if the projection lamp has been securely installed. Please 
    refer to the “Replacing the lamp” section.
     Make sure you have removed the lens cap and the projector is 
    switched on.
     Ensure that the “Blank” feature is not turned on.
    Problem: Left of right edge of the image is missing or the image 
    is unstable or noisy
     Press “Re-Sync” on the remote control or on control panel.
     If you are using a PC:
    For Windows 3.x:
    1.  In the Windows Program Manager, double click the “Windows 
    Setup” icon in the Main group.
    2.  Verify that your display resolution setting is less than 
    or equal to 
    1600 x 1200.
    For Windows 95, 98, 2000, XP:
    1. From the “My Computer” icon, open the “Control Panel” folder, 
    and double click the “Display” icon.
    2.  Select the “Settings” tab. 
    3.  Click on the “Advanced Properties” button.
    If the projector is still not projecting the whole image, you will also \
    need to change the monitor display you are using. Refer to the 
    following steps.
    4. Verify the resolution setting is less than or equal to 1600 x 1200 
    resolution.
    Troubleshooting
    If you experience trouble with the projector, refer to the 
    following information. If the problem persists, please 
    contact your local reseller or service center. 
    						
    							
    44  © 3M 2008.  All Rights Reserved.
    
    Appendices  3M™ Super Close Projection System  
    
    5. Select the “Change” button under the “Monitor” tab.
    6.  Click on “Show all devices.” Next, select “Standard monitor 
    types” under the SP box; choose the resolution mode you need 
    under the “Models” box.
     If you are using a Notebook:
    1.  First, follow the steps above to adjust resolution of the 
    computer.
    2.  Press the toggle output settings. example: [Fn]+[F3]
     If you experience difficulty changing resolutions or your monitor 
    freezes, restart all equipment including the projector.
    Problem: The screen of the Notebook or PowerBook computer 
    is not displaying a presentation
     If you are using a Notebook PC:
    Some Notebook PCs may deactivate their own screens when a 
    second display device is in use. Each has a different way to be 
    reactivated. Refer to your computer’s documentation for detailed 
    information.
    Problem: Image is unstable or flickering
     Use “Phase” to correct it. (see page 36)
     Change the monitor colour setting on your computer.
    Problem: Image has vertical flickering bar
     Use “Frequency” to make an adjustment. (see page 36)
     Check and reconfigure the display mode of your graphic card to 
    make it compatible with the product. 
    HP & Compaq   [Fn]+[F4]
    Dell    
      [Fn]+[F8]
    Gateway  
      [Fn]+[F4]
    Mac Apple: System PreferenceDisplayArrangementMirror display
    IBM    [Fn]+[F7]
    NEC  
       [Fn]+[F3]
    Toshiba  
       [Fn]+[F5]   
    						
    							
    © 3M 2008.  All Rights Reserved.  45
    
    3M™ Super Close Projection System Appendices
    
    MessagePower-LEDTemp-LEDLamp-LED(Blue)(Red)
    Standby State (Plug in power cord)
    WarmingFlashing
    Normal Mode
    CoolingFlashing
    Error (Lamp failed)
    Error (Fan failed)Flashing
    Error (Over Temp.)
    Problem: Image is out of focus
     Adjust the Focus Ring on the projector lens.
     Make sure the projection screen. (see pages 18-19)
    Problem: The image is stretched when displaying 16:9 DVDThe projector automatically detects 16:9 DVD and adjusts the aspect ratio by digitizing to full screen with 4:3 default setting.
    If the image is still stretched, you will also need to adjust the aspect\
     
    ratio by referring to the following:
     Please select 4:3 aspect ratio type on your DVD player if you are playing a 16:9 DVD.
     If you can’t select 4:3 aspect ratio type on your DVD player, please select 4:3 aspect ratio in the on screen menu.
    Problem: Image is reversed
     Select “Management-2/3  Mounting or Rear” from the OSD and 
    adjust the projection direction. (see page 29)
    Problem: Lamp burns out or makes a popping sound
     When the lamp reaches its end of life, it will burn out and may 
    make a loud popping sound. If this happens, the projector will not 
    turn on until the lamp module has been replaced. To replace the 
    lamp, follow the procedures in the “Replacing the Lamp”. 
    (see page 47)
    Problem: LED lighting message
     •  Steady light  No light   
    						
    All 3M manuals Comments (0)

    Related Manuals for 3M Super Close Projection System SCP715/SCP740/SCP717 Operators Guide