3M Super Close Projection System SCP715/SCP740/SCP717 Operators Guide

							
16  © 3M 2008.  All Rights Reserved.

Installation  3M™ Super Close Projection System  

LED Indicator
 When the “TEMP” indicator turns red, it indicates the 
projector has overheated. The projector will automatically 
shut itself down.
  When the “LAMP” indicator turns red, it indicates a problem 
with the lamp. Turn off the projector and disconnect the 
power cord from the electrical outlet, then contact your local 
dealer or our service center.
  When the “LAMP” indicator flashes red, it indicates the 
fan has failed. Stop using the projector and disconnect the 
power cord from the electrical outlet, then contact your local 
dealer or our service center.
Powering Off the Projector
1.  Press the “Power/Standby” button to turn off the projector 
lamp; you will see a message 
displayed on the projecor’s screen. Press the “Power/
Standby” button again to confirm.
2.  The cooling fans continue to operate for about 2 
minutes for 
cooling cycle and the Power LED will flash red. When the 
Power LED stops flashing, the projector has entered standby 
mode.
  Once in standby mode, simply press “Power/Standby” button 
to restart the projector.
3.  Disconnect the power cord from the electrical outlet and the 
projector.
4.  Following a power
 off procedure, please allow 2 minutes 
before attempting to restart the projector.  
						

							
© 3M 2008.  All Rights Reserved.  17

3M™ Super Close Projection System Installation

Adjusting the Projected Image
Adjusting the Projector Image Height
The projector is equipped with elevator feet for adjusting 
the image height.
 To raise the image:
1.  Press the elevator buttons 
.
2.  Raise the image to the desired height angle 
, then re-
lease the button to lock the elevator feet into position.
3.  Rotate the tilt adjusting foot 
 to fine-tune the display 
angle.
 To lower the image:
1.  Press the elevator buttons.
2.  Lower the image, then release the button to lock the 
elevator feet into position.
3.  Rotate the tilt adjusting foot 
 to fine-tune the display 
angle.
Elevator FeetTilt Adjusting FootElevator Feet
Elevator Buttons
11
223   
						

							
18  © 3M 2008.  All Rights Reserved.

Installation  3M™ Super Close Projection System  

36.2(91.9cm)
72.4(183.8cm)
144.7(367.6cm)
217.1(551.5cm)
289.5(735.3cm)
300.0(762.0cm)
1.64(0.5m)
13.12(4.0m)9.84(3.0m)6.56(2.0m)3.28(1.0m)
Width
HeightDiagonal
13.60(4.1m)
Hd

Focus Ring
Adjusting the Projector Focus
To focus the image, rotate the focus ring until the image is 
clear.
Screen(Diagonal)36.2”(91.9cm)72.4”(183.8cm)144.7”(367.6cm)217.1”(551.5cm)289.5”(735.3cm)300.0”(762.0cm)
Screen Size(WxH)28.95”x 21.71”73.5 x 55.2cm57.90” x 43.42”147.1 x 110.3cm115.79” x 86.84”294.1 x 220.6cm173.69” x 130.27”441.2 x 330.9cm231.59” x 173.69”588.2 x 441.2cm240.00” x 180.00”609.6 x 457.2cm
Hd2.17” (5.5cm)4.34” (11.0cm)8.68” (22.1cm)13.03” (33.1cm)17.37” (44.1cm)18.00” (45.7cm)
Distance1.64’ (0.5m)3.28’ (1.0m)6.56’ (2.0m)9.84’ (3.0m)13.12’ (4.0m)13.60’ (4.1m)
 This graph is for user’s reference only.
3M Super Close Projection System SCP715/
SCP717 Adjusting Projection Image Size
The projector will focus at distances from 1.64 to 13.60 feet 
(0.5 to 4.1 meters).                                   
						

							
© 3M 2008.  All Rights Reserved.  19

3M™ Super Close Projection System Installation

67.3(170.9cm)
134.6(341.8cm)
201.9(512.7cm)
269.1(683.6cm)
336.4(854.5cm)
1.64(0.5m)
13.12(4.0m)9.84(3.0m)6.56(2.0m)3.28(1.0m)
33.7(85.5cm)
16.40(5.0m)
Width
HeightDiagonal
Hd

3M Super Close Projection System SCP740 
Adjusting Projection Image Size
Screen(Diagonal)33.7”(85.5cm)67.3”(170.9cm)134.6”(341.8cm)201.9”(512.7cm)269.1”(683.6cm)336.4”(854.5cm)
Screen Size(WxH)28.54” x 17.84”72.5 x 45.3cm57.05” x 35.65”144.9 x 90.6cm114.10” x 71.31”289.8 x 181.1cm171.15” x 106.97”434.7 x 271.7cm228.20” x 142.62”579.6 x 362.3cm285.25” x 178.28”724.5 x 452.8cm
Hd8.21” (20.8cm)16.40” (41.7cm)32.80” (83.3cm)49.21” (125.0cm)65.61” (166.6cm)82.01” (208.3cm)
Distance1.64’ (0.5m)3.28’ (1.0m)6.56’ (2.0m)9.84’ (3.0m)13.12’ (4.0m)16.40’ (5.0m)
 This graph is for user’s reference only.
The projector will focus at distances from 1.64 to 16.40 feet 
(0.5 to 5.0 meters).                                   
						

							
20  © 3M 2008.  All Rights Reserved.

User Controls  3M™ Super Close Projection System

Control Panel & Remote Control
There are two ways for you to control the functions: 
Remote Control and Control Panel.
Using the Control Panel
Power/Standby Refer to the “Power On/Off the Projector” section 
on pages 15-16.
Re-Sync Automatically synchronize the projector to the 
input source.
Source Press “Source” to select an input signal.
MenuTurn the menu On or Off.
Four 
Directional 
Select Keys
Use     to navigate through the menus.
Enter Confirm your item selection.
 / 
Keystone
Adjust image distortion caused by tilting the pro-
jector (±16 degrees). 
						

							
© 3M 2008.  All Rights Reserved.  21

3M™ Super Close Projection System User Controls

Using the Remote Control
 PowerRefer to the “Power On/Off the Projector” section 
on pages 15-16.
MuteMomentarily turn off the audio. Press this button again to unlock.
BlankMomentarily turn off the video. Press this button again to unlock.
TimerStart the function of “Presentation Timer”. Press 
this button again to close. (see page 29)
FreezePress “Freeze” to pause the screen image. Press this button again to unlock.
Display FormatDisplay the “Aspect Ratio” section of the on-
screen display menu to select the desired aspect 
ratio.
Display ModeSelect the display mode from PC, Photo, Video, 
Cinema, sRGB and User.
Mouse ControlUse this button to navigate the mouse on the 
page.
Mouse Right 
Click
Mouse right click.
Mouse Left 
Click
Mouse left click.
Pg Page Up Use this button to page up.
Pg Page Down Use this button to page down.
 Zoom In Zoom in to magnify the image.
 Zoom Out Zoom out to reduce the image.
Four 
Directional 
Select Keys
Use      to navigate through the menus.
Re-Sync Automatically synchronize the projector to the 
input source.  
						

							
22  © 3M 2008.  All Rights Reserved.

User Controls  3M™ Super Close Projection System

MenuDisplay or exit the on-screen display menus for 
projector.
ClearClear your selection.
EnterConfirm your item selection.
Source LockSelect auto detection all connector ports or lock 
current connector port.
VideoChoose composite video source.
S-VideoChoose S-Video source.
VGA1Choose RGB1-In or SCART source.
VGA2Choose RGB2-In source.
DVIChoose DVI-D source. 
						

							
© 3M 2008.  All Rights Reserved.  23

3M™ Super Close Projection System User Controls

The Projector has multilingual On Screen Display menus 
that allow you to make image adjustments and change a 
variety of settings. The projector will automatically detect 
the source.
How to Operate 
1. To open the OSD menu, press “Menu” on the Remote Control or 
Control Panel.
2. When OSD is displayed, use   keys to select any item in the 
main menu. While making a selection on a particular page, press 
 key to enter sub menu.
3. Use   keys to select the desired item and adjust the settings 
by   key. 
4. Select the next item to be adjusted in the sub menu and adjust as 
described above.
5. Press “Menu” to confirm, and the screen will return to the main 
menu.
6. To exit, press “Menu” again. The OSD menu will close and the 
projector will automatically save the new settings.
On Screen Display Menus
Main Menu
Sub MenuSetting  
						

							
24  © 3M 2008.  All Rights Reserved.

User Controls  3M™ Super Close Projection System

Menu Tree-1/2 
						

							
© 3M 2008.  All Rights Reserved.  25

3M™ Super Close Projection System User Controls

Menu Tree-2/2