3M Super Close Projection System SCP715/SCP740/SCP717 Operators Guide

36  © 3M 2008.  All Rights Reserved.

User Controls  3M™ Super Close Projection System

 •  “Frequency”, “Phase”, “H Position” and “V Position” functions are only supported under Computer mode.
 Sharpness
Adjust the sharpness of the image.
 Press the  to decrease the sharpness.
 Press the  to increase the sharpness.
  Frequency
“Frequency” changes the display data frequency to match the 
frequency of your computer’s graphic card. If you experience a 
vertical flickering bar, use this function to make...

© 3M 2008.  All Rights Reserved.  37

3M™ Super Close Projection System User Controls

 DHCP
On:   
Assign an IP address to the projector from the DHCP server 
automatically.
 Off: Assign an IP address manually. 
 IP Address
Select an IP address.
 Subnet Mask
Select subnet mask number.
 Gateway
Select the default gateway of the network connected to the 
projector.
 DNS
Select DNS number.
 Apply
Press “Yes” to apply the selection.
 Status
To display network information.
LAN  

38  © 3M 2008.  All Rights Reserved.

User Controls  3M™ Super Close Projection System

1.  Fill  in  a  new  IP,  a  subnet  mask,  a  gateway  and  a  DNS  in  the  dia-
logue box.
2.  
Then  choose  apply  and  press  “Enter”  button  to  effectuate  the  con-
figuration process.
3.   Open  your  web  browser  and  type  in  from  the  OSD  LAN  screen 
then the web page will display as below:
4.  Open “Control Panel” to control your projector. 
 
How to use web browser to control your projector
 •...

© 3M 2008.  All Rights Reserved.  39

3M™ Super Close Projection System User Controls

For example:  
Use Microsoft Internet Explorer (IE) web browser to control the projec\
-
tor, the IP address is http://10.0.50.100.
Step 1:  Find an IP Address (10.0.50.100) from LAN function of 
projector.
Step 2:   Select apply and press 
“Enter” button to submit function or 
press “menu” key to exit.
Step 3:   
To open Network Connections, click Start, click Control 
Panel, click Network and Internet Connections,...

40  © 3M 2008.  All Rights Reserved.

User Controls  3M™ Super Close Projection System

Step 7:  
The Local Area Network (LAN) 
Setting dialog box appears, In 
the Proxy Server area, cancel 
the Use a proxy server for your 
LAN check box., then click “OK” 
button twice.
Step 8:   Open your IE and type in the IP address of 10.0.50.100 in 
the URL then press “Enter” key. The web page will display 
as below:
Step 9:  Open “Control Panel” to control your projector.       

© 3M 2008.  All Rights Reserved.  41

3M™ Super Close Projection System User Controls

 Security Enable
On:   Choose “On” to enable security verification when turning on 
the projector.
 Off:  
Choose “Off” to be able to switch on the projector without 
password verification.
 Security Timer
The function can be selected the time (month/day/hour) to set the number of hours the projector can be used. Once this time has elapsed you will be requested to enter your password again. (Use number buttons on...

42  © 3M 2008.  All Rights Reserved.

User Controls  3M™ Super Close Projection System
 Change Password:
1. Press “Enter” to input old password.
2.  Use number button to enter current password, and then 
press “Enter” to confirm.
3.  Enter new password (4 digits in length) using the number 
buttons on the remote, then press “Enter” to confirm.
4.  Enter new password again and press “Enter” to confirm. 

© 3M 2008.  All Rights Reserved.  43

3M™ Super Close Projection System Appendices
Problem: No image appears on screen
 Ensure all the cables and power connections are correctly and 
securely connected as described in the “Installation” section.
 Ensure the pins of connectors are not crooked or broken.
 Check if the projection lamp has been securely installed. Please 
refer to the “Replacing the lamp” section.
 Make sure you have removed the lens cap and the projector is 
switched on.
 Ensure that...

44  © 3M 2008.  All Rights Reserved.

Appendices  3M™ Super Close Projection System  

5. Select the “Change” button under the “Monitor” tab.
6.  Click on “Show all devices.” Next, select “Standard monitor 
types” under the SP box; choose the resolution mode you need 
under the “Models” box.
 If you are using a Notebook:
1.  First, follow the steps above to adjust resolution of the 
computer.
2.  Press the toggle output settings. example: [Fn]+[F3]
 If you experience difficulty changing resolutions or...

© 3M 2008.  All Rights Reserved.  45

3M™ Super Close Projection System Appendices

MessagePower-LEDTemp-LEDLamp-LED(Blue)(Red)
Standby State (Plug in power cord)
WarmingFlashing
Normal Mode
CoolingFlashing
Error (Lamp failed)
Error (Fan failed)Flashing
Error (Over Temp.)
Problem: Image is out of focus
 Adjust the Focus Ring on the projector lens.
 Make sure the projection screen. (see pages 18-19)
Problem: The image is stretched when displaying 16:9 DVDThe projector automatically detects 16:9 DVD and...