3M Super Close Projection System SCP715/SCP740/SCP717 Operators Guide

26  © 3M 2008.  All Rights Reserved.

User Controls  3M™ Super Close Projection System

 Information
To display the projector information on the screen.
 Service Center:   
To display the location of 3M world wide service 
centers. 
                              
 Source:  
To display the input source information.
 Format:  
To display the resolution of projection image.
 Frame Rate:   
To display the frame rate of projection image.
 Display Mode:   
To display the present of image.
 Display...

© 3M 2008.  All Rights Reserved.  27

3M™ Super Close Projection System User Controls

 Language
Choose the multilingual OSD menu. Use the  or  key to select 
your preferred language. 
Press “Enter” to finalize the selection. 
 Keystone
Press the  or  to adjust image distortion vertically and make a 
squarer image.
 Eco Mode
Choose “On” to use less brightness from the projector lamp, yet wi\
ll 
make the projector lamp last longer. 
 High Altitude
Choose “On” to turn on High Altitude mode. Operate the...

28  © 3M 2008.  All Rights Reserved.

User Controls  3M™ Super Close Projection System

 Information
On:   Choose “On” to display source information on the screen. 
Off:  Choose “Off” to hide source information on the screen. 
 Keypad Lock
When the keypad lock function is on, the control panel will be 
locked, but the projector can still be operated by the remote control. 
If canceling this function, use the remote control or press the “Ente\
r”  
key on the control panel for 7 seconds to turn it off....

© 3M 2008.  All Rights Reserved.  29

3M™ Super Close Projection System User Controls

 Auto Power Off
Set the countdown timer interval. The countdown timer will start 
when there is no signal being sent to the projector. Then projector 
will automatically power off when the countdown has finished.  
(in minutes)
 Presentation Timer
Set the countdown timer for presentation (in minutes). After setting 
the timer, press “Timer” button on the remote control to start the 
function.
 
In the last minute, the...

30  © 3M 2008.  All Rights Reserved.

User Controls  3M™ Super Close Projection System

 Volume
 Press  to decrease the volume.
 Press  to increase the volume.
 Logo
Use this function to select your desired startup screen. If you change the setting from one to another, when you exit the OSD 
menu, the new setting will take effect on next open. 
 3M: The default startup screen of 3M projector.
 User: Use memorize picture from “Logo Capture” function.
  Logo Capture
Press “Yes” to immediately capture...

© 3M 2008.  All Rights Reserved.  31

3M™ Super Close Projection System User Controls

 RS232 Command
 RS232: Allow RS232 control of an individual projector. 
 RJ45:   
Allow network LAN via web browser (Internet Explorer) to 
control of projector. (Default setting) 
 Projector ID
ID definition can be set up by menu (range 01~99), and allow user 
control an individual projector by RS232. Refer to page 49 for the 
complete list of RS232 commands. 
 Signal Power On
On:   
The projector will...

32  © 3M 2008.  All Rights Reserved.

User Controls  3M™ Super Close Projection System

 Display Mode
There are many factory presets optimized for various types of 
images.
 PC: For computer or notebook. (brightest image)
 Photo: For optimum color at high brightness.
 Video: For playing video in a bright environment.
 sRGB: For standard PC color. (best color reproduction)
 User: Memorize user’s settings.
  Brightness
Adjust the brightness of the image.
 Press the  to darken image.
 Press the  to...

© 3M 2008.  All Rights Reserved.  33

3M™ Super Close Projection System User Controls

 Tint
Adjust the color balance of red and green.
 Press the  to increase the amount of green in the image.
 Press the  to increase the amount of red in the image.
  Gamma
This unit comes with 4 preset gamma curves. After the initial setup and fine tuning is completed, utilize the Gamma Adjustment steps to 
optimize your image output.
 White Intensity
Use the white peaking control to set the white peaking level of...

34  © 3M 2008.  All Rights Reserved.

User Controls  3M™ Super Close Projection System

 Gamma Red/ Gamma Green/ Gamma Blue: Adjust the gamma curves of the individual colors.
 Enhance Red/ Enhance Green/ Enhance Blue/ Enhance Cyan/ 
Enhance Magenta/ Enhance Yellow: Adjust the advanced 
saturation adjustment of the individual colors. 
  For example:
+ Red- RedEnhance Red 

© 3M 2008.  All Rights Reserved.  35

3M™ Super Close Projection System User Controls

 Display Format
Use this function to choose your desired aspect ratio.
 Auto :   Keep the image with original width-higth ratio and maxi-
mize the image to fit native horizontal or vertical pixels. 
 4:3 :  
The input source will be scaled to fit the projection screen. 
 16:9 :   
The input source will be scaled to fit the width of the 
screen.
 Full :   Resize image to fit full screen by width (1280 pixels) and...