Zanussi Zwy 1100 User Manual
Have a look at the manual Zanussi Zwy 1100 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 276 Zanussi manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
ENUser manual 2 FRNotice d'utilisation 13 Washing Machine Lave-linge ZWY 1100 ZWY 180
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 Product description _ _ _ _ _ _ _ _ _ _ _ _ _ 3 How to run a wash cycle? _ _ _ _ _ _ _ _ _ _ 4 Daily Use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5 Programmes table _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6 Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7Operating Problems _ _ _ _ _ _ _ _ _ _ _ _ _ 8 Detergents and Additives _ _ _ _ _ _ _ _ _ _ 9 Technical Specifications _ _ _ _ _ _ _ _ _ _ 10 Consumption values _ _ _ _ _ _ _ _ _ _ _ _ 10 Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 11 Environment concerns _ _ _ _ _ _ _ _ _ _ _ 12 Subject to change without notice. Safety information Please read these points carefully before instal- ling and using your appliance. Keep this user manual with your appliance. General safety • Do not modify or attempt to modify this appli- ance. This would put yourself in danger. • Ensure that all coins, safety pins, brooches, screws etc have been removed before start- ing a washing programme. If left in washing, they can seriously damage the appliance. • Use the recommended quantity of detergent. • Put small items together (socks, belts etc.) in a small linen bag or pillow case. • Unplug and close inlet hose tap after using appliance. • Always disconnect the power supply from the appliance before cleaning or mainte- nance. • Do not machine wash clothes with ribbing, unfinished or torn material. Installation • Unpack or ask for the appliance to be un- packed immediately upon delivery. Check the outside of the appliance is not damaged in any way. Report all transit damage to your re- tailer. • Remove all transit bolts and packaging be- fore installing the appliance. • Connection to the water supply must be car- ried out by a qualified plumber. • If your domestic electrical circuit needs adapting to allow the appliance to be plug- ged in, use a qualified electrician.• Ensure that, after installation, the power ca- ble is not trapped under the appliance. • If the appliance is installed on carpeted floor, ensure that the carpet does not obstruct any ventilation ducts located at the base of the appliance. • The appliance must be equipped with an earthed power plug which conforms to regu- lations. • Before connecting your appliance to the power supply, carefully read the instructions in the chapter entitled “Electrical connec- tion”. • Replacing the power cable should only be carried out by an authorised service engi- neer. • The manufacturer cannot be held responsible for any damage resulting from incorrect in- stallation. Precautions to be taken against frost If your appliance is exposed to temperatures below 0°C, the following precautions must be taken: • Close the tap and disconnect the inlet hose. • Place the end of this hose and the drain hose in a basin on the floor. • Select the Drain programme let it run until the end of the cycle. • Disconnect the appliance from the power supply by turning the programme selector to “Stop” . • Unplug the appliance. • Replace the inlet hose and drain hose. 2 www.zanussi.com
This way, the water remaining in the hoses will be drained away, avoiding any ice formation which would damage your appliance. Before turning your appliance on again, ensure that it is installed in an area where the tempera- ture will not fall below freezing. Use • Your appliance is intended for normal do- mestic use. Do not use the appliance for commercial or industrial purposes or for any other purpose. • Refer to the instructions on the label of each item before washing. • Do not put items into the washing machine which have had stains removed with petrol,alcohol, trichlorethylen etc. If such stain re- movers have been used, wait until the prod- uct has evaporated before putting these items into the drum. • Empty pockets and unfold items. • This appliance is not intended for use by per- sons (including children) with reduced physi- cal, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction con- cerning use of the appliance by a person re- sponsible for their safety. Children should be supervised to ensure that they do not play with the appliance. Product description 1 2 3 1. The control panel 2. Lid handle 3. Adjustable levelling feet 3 www.zanussi.com
The control panel 1234 1. Programme selector 2. Pushbuttons and their functions 3. Lights of cycle progress 4. "Start/Pause" pushbutton Dispenser box 1 2 3 4 5 1 Softener (do not fill above the MAX symbol ) 2 Bleaching agent can be used on Cot- ton programmes without prewash - 1/4 to 1 glass of diluted bleach (do not fill above the MAX symbol) 3 Wash 4 Prewash 5Fabric softener and bleach overflow (if overfilled) How to run a wash cycle? Using for the first time • Ensure the electrical and water connec- tions comply with the installation in- structions.• Remove the polystyrene insert and all other items inside the drum. • Run an initial wash cycle at 90°C, with- out any washing but with detergent to clean the water tank. 4 www.zanussi.com
Daily Use Loading washing • Open the lid of the appliance. • Open the drum by depressing the locking button A: The two shutters unlock automati- cally. •Load the washing, close the drum and the lid of your washing machine. Warning! Before closing the lid of your appliance, ensure that the drum is properly closed : • When the two shutters are closed, • locking button A released. Proportioning of detergents Pour the amount of washing powder into the washing and prewash compartments if you have selected the “prewash” option. Pour fabric softener into the compartment and bleach into the compartment if necessary (available on programmes Cotton without pre- wash). Selection of desired programme Turn the programme selector to the required programme. The “4” pushbutton flashes green. If you turn the programme selector to another programme while a cycle is in progress, the ap- pliance will ignore the new selected pro- gramme. The “4” pushbutton flashes red for a few seconds. Selecting the spin speed Press the “Spin” pushbutton to change the spin speed, if you want your washing to be spun at a different speed to the one selected by the appliance. can also select “Rinse hold” . Rinse hold By selecting this function the water of the last rinse is not emptied out to prevent the fabrics from creasing. A At the end of the programme, if you have selec- ted the “Rinse hold” , you then need to select a “Spin” or “Drain” programme to finish the cycle and empty the water. The maximum spin speeds are : for Cotton, Eco : 1000 rpm (ZWY1100), 800 rpm (ZWY180), for Wool, Handwash : 1000 rpm (ZWY1100), 800 rpm (ZWY180), for Syn- thetics : 800 rpm (ZWY180/1100), for Deli- cates : 700 rpm. At the end of the programme, if you have selec- ted “Rinse hold” , you then need to select a “Spin” or “Drain” programme to finish the cycle and empty the water. Selecting options You must select the different options after se- lecting the programme and before pressing the “Start/Pause” pushbutton (see “Pro- grammes table”). Press the desired button(s) : the corresponding lights come on. If pressed again, the lights go out. If one of the options is not compatible with the selected programme, the “Start/Pause” pushbutton flashes red. “Prewash” option The appliance runs a prewash at 30°C max. “Super quick” option The washing time will be reduced depending on the programme selected. “Rinse plus” option The washing machine will add one or more rin- ses during the cycle. This option is recommen- ded for people with sensitive skin and in soft water areas. Temporary : Press the “Rinse plus” push- button. The option is only active for the selec- ted programme. Permanent : Hold down the “Options” and “Rinse plus” pushbuttons for a few seconds. The option is permanently activated, even if the appliance is switched off. To deactivate it, re- peat the process. 5 www.zanussi.com
Start of the programme Press the “Start/Pause” button to start the cy- cle. The corresponding light will come on green. It is normal for the programme selector to remain stationary during the cycle. The light corresponding to the current cycle is illumina- ted. + : Prewash + Wash + : Rinses + Spin : End of cycle Interrupting a programme Adding washing during the first 10 mi- nutes Press the “Start/Pause” pushbutton : the corresponding light will flash green while the appliance is paused. The lid can only be opened around 2 minutes after the washing machine has come to a stop. Press the “Start/ Pause” pushbutton again to continue the programme. Modifying the programme in progress Before making any changes to the current pro- gramme, you need to pause the washing ma- chine by pressing the “Start/Pause” push- button. If the modification is not possible, the “Start/Pause” pushbutton flashes red for a few seconds. If you still decide to change the programme, you must cancel the current pro- gramme (see below). Cancelling the programme If you want to cancel the programme, turn the programme selector to the “Stop” position . End of the programme The washing machine stops automatically, the “Start/Pause” pushbutton goes out and the light “End of cycle” comes on. The lid can only be opened around 2 minutes after the washing machine has come to a stop. Turn the programme selector to the “Stop” position . Remove washing. Unplug and close water inlet tap. Stand by: once the programme has fin- ished after a few minutes the energy sav- ing system is enabled with the pilot lights switched on. By pressing any button the appli- ance will come out of the energy saving status. Programmes table Programme / Type of washingLoadPossible options Cotton (cold - 90°) : White or colour, e.g. normally soiled work clothes, bed linen, table lin- en, body linen, towels.5,0 kgPrewash, Super quick, Rinse plus, Rinse hold Eco 1) (40° - 60°) : White or colour, e.g. nor- mally soiled work clothes, bed linen, table linen, body linen, towels.5,0 kgPrewash, Rinse plus, Rinse hold Synthetics (cold - 60°) : Synthetic fabrics, body linen,fab, coloured farics, non-iron shirts, blouses.2,5 kgPrewash, Super quick, Rinse plus, Rinse hold Delicates (30° - 40°) : For all delicate mate- rials, for example curtains.2,5 kgPrewash, Super quick, Rinse plus, Rinse hold Wool (30° - 40°) : Machine washable wool carrying the labels “pure new wool, machine washable, does not shrink”.1,0 kgRinse hold Handwash (cold - 30°) : Very delicate items carrying the “wash by hand” label.1,0 kgRinse hold 6 www.zanussi.com
Programme / Type of washingLoadPossible options Rinses : Hand washed items can be rinsed in this programme.5,0 kgRinse plus, Rinse hold Drain : Runs an empty cycle after a Rinse hold (or Night cycle plus).5,0 kg Spin : A spin cycle from 500 to 800/10002) after a Rinse hold option. 5,0 kg 1) Standard programmes for the Energy Label consumption values According to regulation 1061/2010, the “Eco 60 °C” and “Eco 40 °C” are respectively the “standard 60 °C cotton programme” and the “standard 40 °C cotton programme”. They are the most efficient programmes in terms of combined energy and water consumptions for washing normally soiled cotton laundry. The water temperature of the washing phase may differ from the temperature declared for the selected programme. 2) Depending on model. Care and cleaning Unplug the appliance before cleaning. Descaling the appliance To descale the appliance, use an appropriate non-corrosive product designed for washing machines. Read product label for recommen- ded amounts and how often descaling should be carried out. The exterior Use warm soapy water to clean the exterior of the appliance. Never use alcohol, solvents or similar products. Dispenser box To clean, proceed as follows : Drain filter Regularly clean the drain filter which is located at the bottom of the drum : 1 2 4 356 7 www.zanussi.com
7 8 9 10 CLACK 11CLACK Water inlet filters To clean, proceed as follows : Operating Problems Numerous checks were carried out on your ap- pliance before it left the factory. However, should you notice a malfunction, please refer tothe sections below before contacting the after- sales service. ProblemsCauses The appliance doesn’t start or doesn’t fill:• the appliance isn’t plugged in correctly, the electrical installation isn’t work- ing, there is a power failure, • the lid of your appliance and the drum shutters aren’t closed firmly, • the programme start command hasn’t been properly selected, • the water supply has been cut off, the water inlet tap is closed, • the water inlet filters are dirty (see “Care and cleaning ”). The appliance fills but empties straight away:• the drainage U-piece is fixed too low (see “Installation”). The appliance doesn’t rinse or doesn’t empty:• the drain hose is blocked or bent, • the drainage filter is obstructed (see “Care and cleaning ”), • the out of balance detector has been activated: washing is unevenly distrib- uted in the drum, • the “Drain” programme or “Night Cycle” or “Rinse hold” option have been selected, • the height of the drainage U-piece is unsuitable. The appliance doesn’t spin:• balance problem with the laundry load: add more laundry or manually adjust the items in the drum. You have found water around the appliance:• too much detergent has caused foam to overflow, • the detergent is unsuitable for machine washing, • the drainage U-piece isn’t attached correctly, • the water inlet hose is leaking. 8 www.zanussi.com
ProblemsCauses The washing results are not satisfactory :• the detergent is unsuitable for machine washing, • there is too much washing in the drum, • the wash cycle is unsuitable, • there isn’t enough detergent. The appliance vibrates, is noisy:• all packaging have not been removed from the appliance (see “Installation”), • the appliance isn’t level and is unbalanced (see “Installation”), • the appliance is too close to the wall or furniture, • washing is unevenly distributed in the drum, the load is too small, • the appliance is in running in period, noise will disappear with time. The wash cycle is much too long:• the water inlet filters are dirty (see “Care and cleaning ”), • the power or water supply has been cut off, • the motor overheating detector has been activated, • the water inlet temperature is lower than usual, • the foam detection security system has been activated (too much detergent) and the washing machine has begun draining the foam, • the out of balance detector has been activated: an extra phase has been added to distribute washing more evenly in the drum. The appliance stops during a wash cycle:• the water or electricity supply is defective, • a “Rinse hold” has been selected, • the drum shutters are open. The lid doesn’t open at the end of the cycle:• the temperature inside the drum is too high, • the lid unlocks 1 - 2 minutes after the end of the cycle. Softener runs directly into the drum when filling the dispenser box:• you have gone past the MAX indicator. The “Start/Pause” push- button 1) flashes red 2): • the lid is not closed properly, • the drainage filter is obstructed, • the drain hose is blocked or bent, • the drain hose is fixed to high (see "Installation"), • the drainage pump is blocked, • the standpipes blocked, • the water tap is closed, the water supply has been cut off. 1) On some models, the audible signals can sound 2) After solving any problems, press "Start/Pause" pushbutton to restart the interrupted programme. Detergents and Additives Only use detergents and additives designed for use in a washing machine. We do not recom- mend mixing different types of detergents. This may spoil the washing. There are no restrictions on the use of powder detergents. Liquid deter- gents must not be used when a prewash hasbeen selected. For cycles without prewash, pour the liquid detergent directly into the drum or use a special dosing device (supplied by the detergent's manufacturer). Detergent tablets or doses must be placed in the detergent com- partment of your appliance's dispenser box. 9 www.zanussi.com
Technical Specifications DIMENSIONSHeight Width Depth850 mm 400 mm 600 mm LINE VOLTAGE /FREQUENCY POWER CONSUMPTION FUSE 230 V / 50 Hz 2300 W 10 A Level of protection against ingress of solid particles and moistureIPX4 Water supplyCold water WATER PRESSUREMinimum Maximum0,05 MPa (0,5 bar) 0,8 MPa (8 bar) Connection to water supply Type 20/27 Consumption values The data of this table are approximate. Different causes can change the data: the quantity and type of laundry, the water and ambient temperature. ProgrammesLoad (kg)Energy con- sumption (kWh)Water con- sumption (li- tre)Approxi- mate pro- gramme duration (minutes)Remaining moisture (%) 1) ZWY 180 Remaining moisture (%) 1) ZWY 1100 Cottons 60 °C51.20581206660 Cottons 40 °C50.780581206660 Synthetics 40 °C2,50.6548803737 Delicates 40 °C2,50.5553703737 Wool/Hand wash 30 °C10.4048543732 Standard cotton programmes Standard 60 °C cotton51.00492146660 Standard 60 °C cotton2,50.81321626660 Standard 40 °C cotton2,50.59331286660 1) At the end of spin phase. Off Mode (W)Left On Mode (W) 0.101.60 10 www.zanussi.com