Zanussi Zdt 110 User Manual

							User
manual
Dishwasher
ZDT 110
156997240en.qxp  12/27/2006  1:39 PM  Page 1
 
						

							2
Content
Safety information  - - - - - - - - - - - - - - - - - - -3
Control panel and functions  - - - - - - - - - - - -4
Audible signals  - - - - - - - - - - - - - - - - - - - - -6
Programme table  - - - - - - - - - - - - - - - - - - -7
Before the first use  - - - - - - - - - - - - - - - - - -8
Setting the water softener  - - - - - - - - - - - - -8
Filling with dishwasher salt  - - - - - - - - - - - -11
Filling with rinse aid  - - - - - - - - - - - - - - - - -12
Adjusting the dosage of rinse aid  - - - - - - -12
Loading cutlery and dishes  - - - - - - - - - - -13
Filling with detergent  - - - - - - - - - - - - - - - -15
Unloading the dishwasher  - - - - - - - - - - - -15
Cleaning and care - - - - - - - - - - - - - - - - - - 16
Environmental concerns - - - - - - - - - - - - - 17
Something not working - - - - - - - - - - - - - - 18
Technical data- - - - - - - - - - - - - - - - - - - - - 20
Consumption values - - - - - - - - - - - - - - - - 20
Hints for Test Institutes - - - - - - - - - - - - - - 21
Installation - - - - - - - - - - - - - - - - - - - - - - - 22
Guarantee/Customer Service - - - - - - - - - - 25
European guarantee - - - - - - - - - - - - - - - - 27
156997240en.qxp  12/27/2006  1:39 PM  Page 2
 
						

							3
Safety information
Correct use
●This dishwasher is only intended for washing
household utensils suitable for machine
washing. 
●Do not put any solvents in the dishwasher.
This could cause an explosion.
●Knives and other items with sharp points
must be loaded in the cutlery basket with
their points down or placed in a horizontal
position in the upper basket.
●Only use products (detergent, salt and rinse
aid) suitable for dishwashers.
●Avoid opening the door whilst the appliance
is in operation, hot steam may escape.
●Do not take any dishes out of the dishwasher 
before the end of the dishwashing cycle.
●After use, isolate the appliance from the
power supply and turn off the water supply.
●This product should be serviced only by an
authorised service engineer, and only
genuine spare parts should be used.
General safety
●Dishwasher detergents can cause chemical
burns to eyes, mouth and throat. Could
endanger life! Comply with the safety
instructions of the dishwasher detergent
manufacturer.
●The water in your dishwasher is not for
drinking. Detergent residues may still be
present in your machine.
●Ensure that the door of the dishwasher is
always closed when it is not being loaded or
unloaded. In this way you will avoid anybody
tripping over the open door and hurting
themselves.
●Do not sit or stand on the open door.
Child safety
●This appliance is designed to be operated by
adults. Don’t allow children to use the
dishwasher unsupervised.
●Keep all packaging well away from children.
There is risk of suffocation.
●Keep all detergents in a safe place out of
children’s reach.
●Keep children well away from the dishwasher
when the door is open.
Installation
●Check your dishwasher for any transport
damage. Never connect a damaged
machine. If your dishwasher is damaged
contact your supplier.
●All packaging must be removed before use.
●Any electrical and plumbing work required to
install this appliance must be carried out by
a qualified and competent person.
●For safety reasons it is dangerous to alter
the specifications or attempt to modify this
product in any way.
In the interest of your safety and to ensure the correct use, before installing and first using the
appliance, read this user manual carefully, including its hints and warnings. To avoid unnecessary
mistakes and accidents, it is important to ensure that all people using the appliance are thoroughly
familiar with its operation and safety features. Save these instructions and make sure that they
remain with the appliance if it is moved or sold, so that everyone using it through its life will be
properly informed on appliance use and safety.
156997240en.qxp  12/27/2006  1:39 PM  Page 3
 
						

							4
Control panel and functions
In this fully integrated appliance the controls are located on the top of the door. When selecting a
washing programme, the door needs to be slightly open.
●Never use the dishwasher if the electrical
supply cable and water hoses are damaged;
or if the control panel, work top or plinth area
are damaged such that the inside of the
appliance is freely accessible. Contact your
local Service Force centre, in order to avoid
hazard.●All sides of the dishwasher must never be
drilled to prevent damage to hydraulic and
electric components.
WARNING!
For electrical and water connection carefully
follow the instructions given in specific
paragraphs.
IMPORTANT!
Always remember that when performing
operations such as: 
- selecting a washing programme, 
- deactivation/activation of the audible signals, 
- setting the water softener, 
the appliance MUSTbe in setting mode:
●Press On-Off button, all programme lights
are illuminated and End of cyclelight
flashes = appliance in setting mode.
●Press On-Off button, a programme light is
illuminated and End of cyclelight is
illuminated with fixed light = last performed
programme still set.
In this case the programme has to be
cancelled (see instructions “Cancel a
washing programme in progress”).
1. On-Offbutton
2. Programme/Cancelbutton
3. End of cyclelight
4. Programme lights
156997240en.qxp  12/27/2006  1:39 PM  Page 4
 
						

							5
Programme/Cancel
button
● Starting the washing programme:
1. Press the On-Off button.
2. Press the Programme/Cancelonce, the light of the last performed 
washing programme illuminates and the End of cyclelight flashes.
3. Press the Programme/Cancelas many times as necessary to illuminate the
light corresponding to the desired programme.
4. Close the dishwasher’s door, the programme will start automatically.
IMPORTANT!
Once the programme has started, if you want to change the selection made you
must cancel the washing programme in progress.
● Cancel the washing programme in progress:
1. Open the door.
2. Press and hold the Programme/Cancelbutton until the light of the running 
programme turns off and the End of cyclelight is flashing.
3. Release the Programme/Cancelbutton.
4. Switch off the machine by pressing the On-Off button or select a new 
washing programme (check that there is detergent in the detergent 
dispenser.
End of cycleIlluminates when a washing programme has ended. 
Switch of the dishwasher by returning the programme selector dial to the Off
position. The On/Off indicator light turns off.
It also has added functions of visual signalling as:
- the setting of the water softener,
- intervention of an alarm due to the malfunction of the machine.
- deactivation/activation of the audible signals.
Audible signals
Audible signals have been introduced to help
indicate which operations the dishwasher is
performing.
- end of the washing programme,
- malfunction of the appliance.Factory setting: audible signals activated.
156997240en.qxp  12/27/2006  1:39 PM  Page 5
 
						

							6
Deactivation/activation of the audible signals
1.The dishwasher must be switched off.
Switch on the dishwasher by pressing the On-Off
button.
2.Press and hold Programme/Cancelbutton until
programme light Aflashes and programme light
Billuminates with fixed light.
3.Press Programme/Cancelbutton again:
programme light Abecomes fixed and
programme light Bstarts flashing.
4.After a few seconds programme light Aturns off,
programme light Bgoes on flashing and End of
cyclelight illuminates with fixed light.
The illumination of the End of cyclelight means
that the audible signals are active.5.To deactivate the audible signals, press the
Programme/-Cancelbutton, the End of cycle
light turns off indicating that the audible signals
have been deactivated.
6.To memorise the operation, switch off the
dishwasher by pressing the On-Off button.
7.To reactivate again the audible signals, follow the
instructions till point 4. Wait a few seconds and
then press the Programme/Cancelbutton, the
End of cyclelight illuminates indicating that the
audible signals have been reactivated.
156997240en.qxp  12/27/2006  1:39 PM  Page 6
 
						

							7
Programme table
65° NORMALNormal soil
Crockery and cutlery
Light soil
Crockery and cutleryMain wash
Final rinse
Normal soil
Crockery and cutleryPrewash
Main wash
2 intermediate rinses
Final rinse
Dry
Prewash
Main wash
1 intermediate rinse
Final rinse
Dry
RINSE & HOLDAny
Partial load (to be completed
later in theday). This
programme does not require the
use of detergent.PrewashCycle description
Use
Programme
156997240en.qxp  12/27/2006  1:39 PM  Page 7
 
						

							8
Before the first use 
When using separate special
(dishwasher) salt, rinse aid and
detergent:
- set the water softener
- add special salt
- fill up with rinse aid
When using tablets that integrate
rinse aid and detergent:
there is no need to fill up with rinse aid
- set the water softener
- add special (dishwasher) salt
When using tablets that integrate
rinse aid, detergent, salt function
and other additives:
there is no need to fill up with special salt or
rinse aid.
Check whether these detergents are suitable
for your water hardness. Follow the
manufacturers instructions.
- Set the water hardness to level 1.
IMPORTANT!
If the drying results are not satisfactory we
recommend that you:
1. Fill up the rinse aid dispenser with rinse aid.
2. Set the rinse aid dosage to position 2.
If you decide in future to use separated
detergents, we advise that you:
- Fill up the salt and rinse aid container.
- Adjust the water hardness setting to the
highest level and perform 1 normal washing
programme without loading any dishes.
- Adjust the water hardness setting according
to the hardness of the water in your area.
- Adjust the rinse aid dosage
Setting the water softener
The dishwasher is equipped with a water
softener designed to remove minerals and salts
from the water supply, which would have a
detrimental or adverse effect on the operation
of the appliance.
The softener should be adjusted according to
the hardness of the water in your area. Your
local Water Authority can advise you on the
hardness of the water in your area.IMPORTANT!
The water softener must be set in both ways:
manually and electronically.
156997240en.qxp  12/27/2006  1:39 PM  Page 8
 
						

							9
Water hardness Number of flashes of the Adjustment of the water 
“end of programme” light hardness setting
in Clarke
1)in °TH2)in mmol/l3)manually electronically
64 - 88 91 - 125 9,0 - 12,5 10 2 level 10
53 - 63 76 - 90 7,6 - 8,9 9 2 level 9
46 - 52 65 - 75 6,5 - 7,5 8 2 level 8
36 - 45 51 - 64 5,1 - 6,4 7 2 level 7
28 - 35 40 - 50 4,0 - 5,0 6 2 level 6
18 - 22 26 - 32 2,6 - 3,2 4 1 level 4
5 - 12 7 - 18 0,7 - 1,8 2 1 level 2
23 - 27 33 - 39 3,3 - 3,9 5 2 level 5
13 - 17 19 - 25 1,9 - 2,5 3 1 level 3
< 5 < 7 < 0,7 1 1 level 1
no salt necessary
1) Clarke degree, measure of the water hardness.
2) (°TH) French degree, measure of the water hardness.
3) (mmol/l) millimol per litre, international unit for water hardness
The water softener is factory set at position 2.
Setting the water softener manually (see table)
Set switch to position 1
or 2
factory
setting
156997240en.qxp  12/27/2006  1:39 PM  Page 9
 
						

							10
Setting the water softener electronically (see table)
The water softener is factory set at position 5.
1.The dishwasher must be switched off.
Switch on the dishwasher by pressing the On-Off
button.
2.Press and hold Programme/Cancelbutton until
programme light Aflashes and programme light
Billuminates with fixed light.
3.Wait until programme light Bturns off,
programme light Agoes on flashing and
simultaneously End of cyclelight starts flashing.
The number of flashes of the End of cyclelight
corresponds to current level set.
The End of cyclelight might flash 5 times, for
example. The flashing is repeated every 5
seconds.4.To change the level, press the
Programme/Cancel button. Each time the button
is pressed the level increases. (Level 1 follows
level 10). The End of cyclelight indicates the
new setting.
5.TTo memorise the operation, switch off the
dishwasher by pressing the On-Off button.
156997240en.qxp  12/27/2006  1:39 PM  Page 10