Zanussi Zdt 110 User Manual

User
manual
Dishwasher
ZDT 110
156997240en.qxp  12/27/2006  1:39 PM  Page 1
 

2
Content
Safety information  - - - - - - - - - - - - - - - - - - -3
Control panel and functions  - - - - - - - - - - - -4
Audible signals  - - - - - - - - - - - - - - - - - - - - -6
Programme table  - - - - - - - - - - - - - - - - - - -7
Before the first use  - - - - - - - - - - - - - - - - - -8
Setting the water softener  - - - - - - - - - - - - -8
Filling with dishwasher salt  - - - - - - - - - - - -11
Filling with rinse aid  - - - - - - - - - - - - - - - - -12
Adjusting the dosage of rinse aid  - - -...

3
Safety information
Correct use
●This dishwasher is only intended for washing
household utensils suitable for machine
washing. 
●Do not put any solvents in the dishwasher.
This could cause an explosion.
●Knives and other items with sharp points
must be loaded in the cutlery basket with
their points down or placed in a horizontal
position in the upper basket.
●Only use products (detergent, salt and rinse
aid) suitable for dishwashers.
●Avoid opening the door whilst the appliance
is in operation, hot...

4
Control panel and functions
In this fully integrated appliance the controls are located on the top of the door. When selecting a
washing programme, the door needs to be slightly open.
●Never use the dishwasher if the electrical
supply cable and water hoses are damaged;
or if the control panel, work top or plinth area
are damaged such that the inside of the
appliance is freely accessible. Contact your
local Service Force centre, in order to avoid
hazard.●All sides of the dishwasher must never be
drilled...

5
Programme/Cancel
button
● Starting the washing programme:
1. Press the On-Off button.
2. Press the Programme/Cancelonce, the light of the last performed 
washing programme illuminates and the End of cyclelight flashes.
3. Press the Programme/Cancelas many times as necessary to illuminate the
light corresponding to the desired programme.
4. Close the dishwasher’s door, the programme will start automatically.
IMPORTANT!
Once the programme has started, if you want to change the selection made you
must...

6
Deactivation/activation of the audible signals
1.The dishwasher must be switched off.
Switch on the dishwasher by pressing the On-Off
button.
2.Press and hold Programme/Cancelbutton until
programme light Aflashes and programme light
Billuminates with fixed light.
3.Press Programme/Cancelbutton again:
programme light Abecomes fixed and
programme light Bstarts flashing.
4.After a few seconds programme light Aturns off,
programme light Bgoes on flashing and End of
cyclelight illuminates with fixed light....

7
Programme table
65° NORMALNormal soil
Crockery and cutlery
Light soil
Crockery and cutleryMain wash
Final rinse
Normal soil
Crockery and cutleryPrewash
Main wash
2 intermediate rinses
Final rinse
Dry
Prewash
Main wash
1 intermediate rinse
Final rinse
Dry
RINSE & HOLDAny
Partial load (to be completed
later in theday). This
programme does not require the
use of detergent.PrewashCycle description
Use
Programme
156997240en.qxp  12/27/2006  1:39 PM  Page 7
 

8
Before the first use 
When using separate special
(dishwasher) salt, rinse aid and
detergent:
- set the water softener
- add special salt
- fill up with rinse aid
When using tablets that integrate
rinse aid and detergent:
there is no need to fill up with rinse aid
- set the water softener
- add special (dishwasher) salt
When using tablets that integrate
rinse aid, detergent, salt function
and other additives:
there is no need to fill up with special salt or
rinse aid.
Check whether these detergents are...

9
Water hardness Number of flashes of the Adjustment of the water 
“end of programme” light hardness setting
in Clarke
1)in °TH2)in mmol/l3)manually electronically
64 - 88 91 - 125 9,0 - 12,5 10 2 level 10
53 - 63 76 - 90 7,6 - 8,9 9 2 level 9
46 - 52 65 - 75 6,5 - 7,5 8 2 level 8
36 - 45 51 - 64 5,1 - 6,4 7 2 level 7
28 - 35 40 - 50 4,0 - 5,0 6 2 level 6
18 - 22 26 - 32 2,6 - 3,2 4 1 level 4
5 - 12 7 - 18 0,7 - 1,8 2 1 level 2
23 - 27 33 - 39 3,3 - 3,9 5 2 level 5
13 - 17 19 - 25 1,9 - 2,5 3 1 level 3
<...

10
Setting the water softener electronically (see table)
The water softener is factory set at position 5.
1.The dishwasher must be switched off.
Switch on the dishwasher by pressing the On-Off
button.
2.Press and hold Programme/Cancelbutton until
programme light Aflashes and programme light
Billuminates with fixed light.
3.Wait until programme light Bturns off,
programme light Agoes on flashing and
simultaneously End of cyclelight starts flashing.
The number of flashes of the End of cyclelight...