Yamaha Waverunner 3 Manual
Here you can view all the pages of manual Yamaha Waverunner 3 Manual. The Yamaha manuals for WaveRunner VXS Owners Manual are available online for free. You can easily download all the documents as PDF.
Page 301
7-48 E –+ELECINDICATION SYSTEM Speedometer display 1. Check: Speedometer display Does not display → Measure the speed sensor output voltage and pulses. Without specification → Replace the multifunction meter. 2. Measure: Speed sensor output voltage and pulses Out of specification → Repair or replace. Speed sensor output voltage (dependant on the paddle wheel position): Less than 400 mV/ More than 11.6 V Output pulse: 2 pulses/one-full turn Measurement steps: Apply DC 12 voltage to the white...
Page 302
7-49 E –+ELECINDICATION SYSTEM Tachometer display 1. Check: Tachometer display Does not display → Check the engine speed using the “Engine monitor” of the Yamaha Diagnostic System. Replace the multifunction meter. Hour meter display 1. Check: Hour meter display Does not display → Replace the multi- function meter. Voltage meter display 1. Check: Voltage meter display Does not display → Check the battery voltage using the “Engine monitor” of the Yamaha Diagnostic System. Replace the multifunction...
Page 303
7-50 E –+ELECINDICATION SYSTEM Overheat warning indicator 1. Check: Overheat warning indicator Not operating → Replace the multifunc- tion meter. Checking steps: Disconnect the thermoswitch (engine) connector 1 (blue) or engine tempera- ture sensor connector 2 (black) or ther- moswitch (exhaust) 3 connector. Connect the jumper lead to the female terminal of the disconnected connector. Check that the multifunction meter over- heat warning indicator comes on and the buzzer sounds. Engine trouble...
Page 304
7-51 E –+ELECINDICATION SYSTEM Diagnostic display 1. Check: Diagnostic display Does not display → Replace the multi- function meter. Checking steps: Remove the coupler of the sensor indi- cated in the multifunction meter. Check if “Irregular” is indicated in the Diagnosis Record of the Yamaha Diag- nostic System. Start the engine and check that the engine check warning indicator comes on and the buzzer sounds. Press the hour meter/voltmeter display select switch 1 and the speedometer display...
Page 305
E HULL HOOD 1 2 3 4 5 6 7 8 9 CHAPTER 8 HULL AND HOOD HANDLEBAR .................................................................................................. 8-1 EXPLODED DIAGRAM ............................................................................. 8-1 REMOVAL AND INSTALLATION CHART ................................................ 8-1 SERVICE POINTS .................................................................................... 8-6 Handlebar inspection...
Page 306
E HULL HOOD FRONT HOOD ............................................................................................... 8-21 EXPLODED DIAGRAM ........................................................................... 8-21 REMOVAL AND INSTALLATION CHART .............................................. 8-21 STEERING CONSOLE COVER .................................................................... 8-25 EXPLODED DIAGRAM ........................................................................... 8-25 REMOVAL...
Page 307
E HULL HOOD DECK AND HULL.......................................................................................... 8-47 EXPLODED DIAGRAM ........................................................................... 8-47 REMOVAL AND INSTALLATION CHART .............................................. 8-47 ENGINE MOUNT ........................................................................................... 8-49 EXPLODED DIAGRAM ..............................................................................
Page 308
8-1 E HULL HOODHANDLEBAR HANDLEBAR EXPLODED DIAGRAM REMOVAL AND INSTALLATION CHART Step Procedure/Part name Q’ty Service points HANDLEBAR COVER REMOVAL Follow the left “Step” for removal. 1Screw 4 2 Handlebar cover 1 3Pad 1 4Bolt 2 NOTE: Position the corrugated tube for the throttle cable as shown in the illustration so that the tube attaches to the end of the outer throttle cable. 5 Handlebar cover stay 1 6 Throttle cable 1 7Bolt 4 8 Upper handlebar holder 2 Reverse the removal steps for installation.
Page 309
8-2 E HULL HOODHANDLEBAR EXPLODED DIAGRAM REMOVAL AND INSTALLATION CHART Step Procedure/Part name Q’ty Service points HANDLEBAR REMOVAL Follow the left “Step” for removal. QSTS cable (to jet thrust nozzle) Refer to “REMOTE CONTROL CABLES AND SPEED SENSOR LEAD”. 1 Nut/washer 2/2 2 QSTS converter 1 3 QSTS cable 2 1 with white tape a 4 QSTS cable 1 1 5 Handlebar switch coupler 2 6 Buzzer coupler 1 7Screw 4 8 Handle boss cover 1 9 Band 2
Page 310
8-3 E HULL HOODHANDLEBAR EXPLODED DIAGRAM Step Procedure/Part name Q’ty Service points 10 Hose packing 1 11 Buzzer 1 12 Handlebar assembly 1 NOTE: Pass the QSTS cable and handlebar switch lead through the handle boss cover, and then install the handlebar assembly. Install the sponges of the QSTS cables as shown and make sure that the grommet is installed to the deck securely. 13 Grommet 2 Reverse the removal steps for installation. Not reusable
All Yamaha manuals