Yamaha Waverunner 3 Manual
Here you can view all the pages of manual Yamaha Waverunner 3 Manual. The Yamaha manuals for WaveRunner VXS Owners Manual are available online for free. You can easily download all the documents as PDF.
Page 271
7-18 E –+ELECIGNITION SYSTEM 2. Measure: Pulser coil output peak voltage Below specification → Replace the pulser coil. NOTE: To crank the engine, connect the engine shut- off cord (lanyard), and then press the start switch and engine stop switch simultaneously. 3. Measure: Lighting coil output peak voltage Below specification → Replace the light- ing coil. NOTE: To crank the engine, connect the engine shut- off cord (lanyard), and then press the start switch and engine stop switch simultaneously....
Page 272
7-19 E –+ELEC 4. Measure: Rectifier/regulator output voltage Below specification → Replace the recti- fier/regulator. NOTE: Before measuring the output peak voltage, make sure that the battery is fully charged. The output voltage gradually increases after the engine is started, therefore, maintain the specified engine speed for approximately 1 minute to measure the output voltage. BATTERY Refer to “ELECTRICAL” in Chapter 3. FUSE Refer to “STARTING SYSTEM”. SPARK PLUGS Refer to “POWER UNIT” in Chapter...
Page 273
7-20 E –+ELEC IGNITION COIL 1. Measure: Primary coil resistance Out of specification → Replace. NOTE: When measuring a resistance of 10 Ω or less with the digital tester, the correct measurement cannot be obtained because of the tester’s internal resistance. Refer to “Low resistance measurement”. Primary coil resistance: Black/white (B/W) – Red (R) 1.53–2.07 Ω at 20 °C (68 °F) 2. Measure: Secondary coil resistance Out of specification → Replace. Secondary coil resistance: 12.5–16.9 k Ω at 20 °C...
Page 274
7-21 E –+ELECIGNITION SYSTEM ENGINE TEMPERATURE SENSOR 1. Measure: Engine temperature sensor resistance (at the specified temperature) Out of specification → Replace. Engine temperature sensor resistance: 20 °C (68 °F): 54.2–69.0 k Ω 100 °C (212 °F): 3.12–3.48 k Ω Measurement steps: Suspend the engine temperature sensor in a container filled with water. Slowly heat the water. Measure the resistance when the speci- fied temperature is reached. INTAKE AIR TEMPERATURE SENSOR 1. Measure: Intake air...
Page 275
7-22 E –+ELECIGNITION SYSTEM THERMOSWITCH (ENGINE) 1. Check: Thermoswitch (engine) continuity (at the specified temperature) Out of specification → Replace. 1 No continuity È Temperature 2 Continuity É Time THERMOSWITCH (EXHAUST) 1. Check: Thermoswitch (exhaust) continuity (at the specified temperature) Out of specification → Replace. 1 No continuity È Temperature 2 Continuity É Time Thermoswitch (engine) continuity temperature: a 84–90 °C (183–194 °F) b 70–84 °C (158–183 °F) Checking steps:...
Page 276
7-23 E –+ELECIGNITION SYSTEM MAIN AND FUEL PUMP RELAY 1. Check: Main and fuel pump relay continuity Faulty → Replace. Checking steps: Connect the tester leads between the main and fuel pump relay terminals 5 , 6 and 7 . Connect the terminals 2 or 3 to the pos- itive battery terminal. Connect the terminal 1 to the negative battery terminal. Check that there is continuity between the main and fuel pump relay terminals. Check that there is no continuity between the main and fuel pump relay...
Page 277
7-24 E –+ELECIGNITION SYSTEM THROTTLE POSITION SENSOR 1. Measure: Throttle position sensor output voltage Out of specification → Adjust the throttle bodies synchronization. Refer to “FUEL INJECTION SYSTEM” in Chapter 4. Test harness (3 pins): YB-06793/90890-06793 Test connector: YW-06862/90890-06862 Throttle position sensor output voltage: Pink (P) – Black/Orange (B/O) 0.760 ± 0.016 V Measurement steps: Connect the test harness (3 pins) to the throttle position sensor 1 . To start the ECM normally,...
Page 278
7-25 E –+ELECIGNITION SYSTEM CAM POSITION SENSOR 1. Measure: Cam position sensor output voltage Out of specification → Replace. NOTE: When operating the Yamaha Diagnostic Sys- tem, electric power is supplied to the cam posi- tion sensor. Test harness (3 pins): YB-06777/90890-06777 Cam position sensor output voltage: Green/orange (G/O) – Black/orange (B/O) Position Voltage (V) A More than 0.8 B Less than 4.8 Measurement steps: Remove the cam position sensor. Connect the test harness (3 pins) to the...
Page 279
7-26 E –+ELECIGNITION SYSTEM INTAKE AIR PRESSURE SENSOR 1. Measure: Intake air pressure sensor output volt- age Out of specification → Replace. È: Output voltage É: Vacuum pressure NOTE: When operating the Yamaha Diagnostic Sys- tem, electric power is supplied to the intake air pressure sensor. Test harness (3 pins): YB-06769/90890-06769 Vacuum/pressure pump gauge set: YB-35956-A/90890-06756 Intake air pressure sensor output voltage: Pink/green (P/G) – Black/orange (B/O) 1101.3 kPa (1.01 kgf/cm 2,...
Page 280
7-27 E –+ELECIGNITION SYSTEM SLANT DETECTION SWITCH 1. Check: Slant detection switch continuity Out of specification → Replace. PositionLead color Blue/black (L/B)Black/ orange (B/O) Normal operation È Overturned É UP UP È É
All Yamaha manuals