Yamaha Rmx 1 Manual

							41 RM1x
ÔçMonitor
No Data When a job is executed, this will appear if the selected track or area contains no data,
making the job invalid. Re-select the area.
Illegal Input This will appear in response to inappropriate operation or input. Check your input
method.
Illegal Track Number An unavailable or otherwise improper track number has been specified. Select a
different track.
Illegal Phrase Number An unavailable or otherwise improper phrase number has been specified. Select a
different phrase.
Illegal Measure An unavailable or otherwise improper measure number has been specified. Select a
different measure number.
Illegal Check Box This message will appear if no check boxes are checked in any of the corresponding
track jobs. At least one check box must be checked.
No F7 (End of Exc.)This message indicates that no “End of Exclusive” byte (F7) was included with a MIDI
exclusive data entry or edit. Be sure to include F7.
Preset PhraseThis will appear when you attempt to edit a Preset Phrase. If you wish to edit a preset
phrase, you must first copy it to a User Phrase.
Preset Pattern This will appear when you attempt to record to a Preset Pattern. You cannot record to
Preset Patterns.
Pattern Length Mismatch A job has resulted in a pattern having more than the maximum of 256 measures.
Phrase Number Overflow All available user phrases (256 maximum) have been used up when recording,
executing a job, or editing.
ÔçSystem
Backup Battery Low This will appear when the internal backup battery of the RM1x has run down. Replace the
battery to a new one.
Memory Full This will appear when internal memory is full and it is not possible to record, edit, execute
a job, receive MIDI, or load from floppy disk. Delete unneeded songs, patterns, or user
phrases, and try the operation once again.
Factory Set After the power is switched ON, a system diagnosis is run on the RM1x’s system. If the
diagnosis finds the RAM to be defective, this message will appear and the memory will be
reset to its original factory settings. Data for User Song, User Patterns, and User Phrases
will all be eliminated.
Memory Protect You have attempted to execute a recording, editing, or job function when the UTILITY
mode Memory Protect function is ON.
ÔçMIDI
Exc. Adrs ErrorThis appears when the received Exclusive data contains an address error.
Exc. Data Error This appears when the received Exclusive data contains a data size error.
MIDI Buffer Full This will appear when the MIDI reception buffer of the RM1x has filled up, and
processing is not possible. Try decreasing the amount of data or increasing the
interval time and transmit the data once again. 
						

							42RM1x
ÔçDisk
Disk Full This will appear if the floppy disk is full and has no room to save the file. Either use a
new floppy disk, or delete unneeded files before trying the operation once again.
File Not Found When loading, this will appear if the specified file does not exist in the floppy disk.
Insert the disk once again, and try the operation again.
Bad Disk         Format Now? The floppy disk is faulty. Press the [Yes +1] button to format the disk.
 (Y/N)
No DiskThis indicates that the floppy disk is not correctly inserted into the RM1x. Insert the
floppy disk correctly.
Unformat         Format Now? This will appear if the floppy disk is not formatted. Press the [Yes +1] button to format
(Y/N)the disk.
Write Protected This will appear if the write-protect slider of the floppy disk is in the write prohibit
position. Remove the floppy disk, close the write-protect slider, and try the operation
once again.
Bad File This will appear when you attempt to load a defective file.
Illegal Format This will appear if the floppy disk is of a format which the RM1x is not able to handle.
Check the contents of the disk.
Disk ChangedThis will appear if you have exchanged disks when you should not have. Try the
operation once again from the beginning.
Can’t Change File Name When renaming, this will appear if the floppy disk already contains a file with a name
identical to the specified filename. Specify a different filename.
Illegal File When loading, this will appear if the specified file cannot be handled by the RM1x.
Check the contents of the file.
No Data When saving data to floppy disk, this will appear if the selected song or style contains
no data, and the save operation is invalid. Select a different song or style.
ÔçMessages other than error messages
Can’t Undo. Ok? (Y/N) If executing a job would fill up the internal memory so that Undo will not be available,
this message will appear. If you are sure that you will not need to Undo this job,
press the [YES +1] button. To cancel without executing the job, press the [NO -1]
button, and delete unneeded songs, patterns, or user phrases before trying the
operation once again.
Are you sure? (Y/N)Before an operation is executed, this message will ask you for confirmation. Use the
[YES +1]/[NO -1] button to either cancel or execute.
CompletedThis will appear when the current process has been completed. Press any button
and the message will disappear.
Executing...When loading, saving, or formatting, this message will appear while the job is being
executed. Please wait.
ÙCONFIRMATION OF MIDI DATA
       If you want to confirm the MIDI data, you can see them on the owner ’s manual or PDF service manual. 
						

							45
YAMAHA  [ Music Sequencer ---       voice part   ]    Date:08-SEP-1998
        Model RMlx    MIDI Implementation Chart       Version : 1.0
Transmitted Recognized Remarks 
       Function ... 
 
 Basic    Default 1 - 16 1 - 16 Memorized
 Channel  Changed 1 - 16 1 - 16
 
          Default 3 1 Memorized
 Mode     Messages x 1 - 4(m=1)   *1
          Altered ************** x
 
 Note 0 - 127 0 - 127 Transpose
 Number : True voice ************** 0 - 127
 Velocity Note ON o  9nH,v=1-127 o v=1-127
          Note OFF x  9nH,v=0 x
 
 After    Keys x x
 Touch    Chs x x
 
 Pitch Bend x o 0-24 semi
 
               0,32 o            *2 o Bank Select
      1,64,66,67,84 x o
       5,7,10,11,65 o            *2 o
               6,38 o            *2 o Data Entry
  Control        16 x o
Assignable Cntrl
        1-31,33-119 o oAssignable Knob
  Change      71-76 o xSound Controller
           91,93,94 o            *2 oEffect SendLevel
              96,97 x o Data Inc,Dec
              98,99 x o NRPN LSB,MSB
            100,101 o            *2 o RPN LSB,MSB
 
 Prog o 0 - 127 o 0 - 127
 Change : True # ***********   0 - 127
 
 System Exclusive o o
 
        : Song Pos. x x
 Common : Song Sel. x x
        : Tune x x
 
 System    :Clock x x
 Real Time :Commands x x
 
 
 Notes:*1 m is always treated as 1 regardless of its value.
       *2 transmit if TG parameter out sw is on.
 
  Mode 1 : OMNI ON,  POLY    Mode 2 : OMNI ON,  MONO         o : Yes
  Mode 3 : OMNI OFF, POLY    Mode 4 : OMNI OFF, MONO         x : No
      : All Sound Offxo
 Aux  : Reset All Cntrlsxo
      : Local ON/OFFxx
 Mes- : All Notes OFFx o(123-127)
 sages: Active Sense o o
      : Reset x x 
						

							46
YAMAHA  [ Music Sequencer ---   sequencer part   ]    Date:08-SEP-1998
        Model RMlx    MIDI Implementation Chart       Version : 1.0
Transmitted Recognized Remarks 
       Function ... 
 
 Basic    Default 1 - 16 1 - 16 Memorized
 Channel  Changed x x
 
          Default x x
 Mode     Messages x x
          Altered ************** x
 
 Note 0 - 127 0 - 127
 Number : True voice **************
 Velocity Note ON o  9nH,v=1-127 o v=1-127
          Note OFF x  9nH,v=0 x
 
 After    Keys o o
 Touch    Chs o o
 
 Pitch Bend o o
 
              0-121 o o
  Control
  Change
 
 Prog o 0 - 127 o 0 - 127
 Change : True # ***********
 
 System Exclusive o o
 
        : Song Pos. o           *2 o           *1
 Common : Song Sel. o           *2 o           *1
        : Tune x x
 
 System    :Clock o           *2 o           *3
 Real Time :Commands o           *2 o           *1
 
 
 Notes:*1 if MIDI control is in or in/out
       *2 if MIDI control is out or in/out
       *3 if MIDI sync is external
       send MMC (stop,deffered play,locate) if sync mode is MTC.
       receive MTC quarter frame message if sync mode is MTC.
  Mode 1 : OMNI ON,  POLY    Mode 2 : OMNI ON,  MONO         o : Yes
  Mode 3 : OMNI OFF, POLY    Mode 4 : OMNI OFF, MONO         x : No       : 
All Sound Offoo
 Aux  : Reset All Cntrlsoo
      : Local ON/OFFoo
 Mes- : All Notes OFFxx
 sages: Active Sense x x
      : Reset x x 
						

							49 RM1x
The RM1x tone generator and sequencer blocks handle different MIDIevents. These are listed seqparately in
the MIDI Data Format as well as in the MIDI Implementation Chart.
n Tone generator block (Voice part)
(1) TRANSMIT FLOW
       SW1
MIDI -+----
IN      |   |
   ------   |
   | --------
   | | SW1
   | |-[]---+--- NOTE OFF 8nH
   | | |
   | | +--- NOTE ON/OFF 9nH
   | | |
   | | +--- CONTROL CHANGE
   | | |   BANK SEL MSB BnH,00H
   | | |   BANK SEL LSB BnH,20H
   | | |   MODULATION BnH,01H
   | | |   PORTAMENTO TIME BnH,05H
   | | |   DATA ENTRY MSB BnH,06H
   | | |   DATA ENTRY LSB BnH,26H
   | | |   MAIN VOLUME BnH,07H
   | | |   PANPOT BnH,0AH
   | | |   EXPRESSION BnH,0BH
   | | |   AC1 CONTROLLER BnH,10H
   | | |   SUSTAIN SWITCH BnH,40H
   | | |   PORTAMENTO SWITCH BnH,41H
   | | |   SOSTENUTO BnH,42H
   | | |   SOFT PEDAL BnH,43H
   | | |   HARMONIC CONTENT BnH,47H
   | | |   RELEASE TIME BnH,48H
   | | |   ATTACK TIME BnH,49H
   | | |   BRIGHTNESS BnH,4AH
   | | |   SOUND CONTROLLER 6 BnH,4BH
   | | |   SOUND CONTROLLER 7 BnH,4CH
   | | |   PORTAMENTO CONTROL BnH,54H
   | | |   EFFECT SEND LEVEL 1 BnH,5BH
   | | |   EFFECT SEND LEVEL 3 BnH,5DH
   | | |   EFFECT SEND LEVEL 4 BnH,5EH
   | | |   DATA ENTRY INC BnH,60H
   | | |   DATA ENTRY DEC BnH,61H
   | | |   NRPN
   | | |     VIBRATO RATE BnH,63H,01H,62H,08H,06H,mmH
   | | |     VIBRATO DEPTH BnH,63H,01H,62H,09H,06H,mmH
   | | |     VIBRATO DELAY BnH,63H,01H,62H,0AH,06H,mmH
   | | |     FILTER CUTOFF FREQ. BnH,63H,01H,62H,20H,06H,mmH
   | | |     FILTER RESONANCE BnH,63H,01H,62H,21H,06H,mmH
   | | |     AEG AT TACK TIME BnH,63H,01H,62H,63H,06H,mmH
   | | |     AEG DECAY TIMEBnH,63H,01H,62H,64H,06H,mmH
   | | |     AEG RELEASE TIME BnH,63H,01H,62H,66H,06H,mmH
   | | |   RPN
   | | |     PITCH BEND SENS. BnH,64H,00H,65H,00H,06H,mmH
   | | |     FINE TUNING BnH,64H,01H,65H,00H,06H,mmH,26H,llH
   | | |     COARSE TUNING BnH,64H,02H,65H,00H,06H,mmH
   | | |     RPN RESET BnH,64H,7FH,65H,7FH
   | | |   ALL SOUND OFF BnH,78H,00H
   | | |   RESET ALL CONTROLLERS BnH,79H,00H
   | | |   ALL NOTE OFF BnH,7BH
   | | |   OMNI MODE OFF BnH,7CH
   | | |   OMNI MODE ON BnH,7DH
   | | |   MONO MODE BnH,7EH
   | | |   POLY MODEBnH,7FH
   | | |
   | | +--- PROGRAM CHANGE CnH
   | | |
   | | +--- PITCH BEND CHANGE EnH
   | |
   | |------+ SYSTEM EXCLUSIV MESSAGE
   | | |   
   | | |------- MIDI MASTER TUNING F0H 43H 1nH 27H 30H 00H 00H mmH llH ccH F7H
   | | |------- XG SYSTEM ON F0H 43H 1nH 4CH 00H 00H 7EH 00H F7H
   | | |------- XG SYSTEM F0H 43H 1nH 4CH aaH aaH aaH ddH.....ddH F7H
   | | |------- MULTI EFFECT F0H 43H 1nH 4CH aaH aaH aaH ddH.....ddH F7H
   | | |------- MULTI PART F0H 43H 1nH 4CH aaH aaH aaH ddH.....ddH F7H
   | |
   | |------+ SYSTEM EXCLUSIV MESSAGE
   |             GM MODE ON F0H 7EH 7FH 09H 01H F7H
   |             MIDI MASTER VOLUME F0H 7FH 7FH 04H 01H llH mmH F7H
   |             IDENTITY REQUEST F0H 7EH 0nH 06H 01H F7H
   |
   |-------+ ACTIVE SENSING FEH
SW1 [] Data received from MIDI will be sounded by part n (n being the receive channel).
(3) TRANSMIT/RECEIVE DATA(3-1) CHANNEL VOICE MESSAGES
  (3-1-1) NOTE OFF
STATUS 1000nnnn(8nH) n = 0 ~ 15 VOICE CHANNEL NUMBER
NOTE NUMBER 0kkkkkkk k = 0 (C-2) ~ 127 (G8)
VELOCITY0vvvvvvv v is ignored
Received only.
  (3-1-2) NOTE ON/OFF
STATUS 1001nnnn(9nH) n = 0 ~ 15 VOICE CHANNEL NUMBER
NOTE NUMBER 0kkkkkkk k = 0 (C-2) ~ 127 (G8)
VELOCITY0vvvvvvv(v­0) NOTE ON
00000000(v=0)NOTE OFF
  (3-1-3) PROGRAM CHANGE
STATUS 1100nnnn(CnH) n = 0 ~ 15 VOICE CHANNEL NUMBER
PROGRAM NUMBER 0ppppppp p = 0 ~ 127
  (3-1-4) PITCH BEND CHANGE
STATUS 1110nnnn(EnH) n = 0 ~ 15 VOICE CHANNEL NUMBER
LSB 0vvvvvvvPITCH BEND CHANGE LSB
MSB 0vvvvvvvPITCH BEND CHANGE MSB
14 bit resolution
   MSB
   00000000B ( 00H )minimum value
   01000000B ( 40H ) center value
   0 1111111 B  (  7FH ) maximum Value
Transmitted according to the Assignable Knobs 1 - 8 settings.
  (3-1-5) CONTROL CHANGE
STATUS 1011nnnn(BnH) n = 0 ~ 15 VOICE CHANNEL NUMBER
CONTROL NUMBER 0ccccccc
CONTROL VALUE0vvvvvvv
* The CONTROL NUMBER to be transmitted.
c =  0 BANK SEL MSB ; v = 0:GM VOICE
     63:RM1x VOICE,
     126:RM1x DRUM KIT,
     127:GM DRUM
c = 32 BANK SEL LSB ; v = 0 - 127 *3
c =  1 MODULATION ; v = 0 - 127
c =  7 MAIN VOLUME ; v = 0 - 127
c = 11 EXPRESSION ; v = 0 - 127
c = 16 AC1 CONTROLLER ; v = 0 - 127 *2
c = 64 SUSTAIN SWITCH ; v = 0-63:OFF , 64-127:ON
c = 1 - 119 (except 32) are transmitted according to the Assignable Knobs 1 - 8 settings.c = 64 is transmitted according to the Foot Switch setting.
* The CONTROL NUMBER to be received.
c =  0 BANK SEL MSB ; v = 0:GM VOICE,
     63:RM1x VOICE,
     126:RM1x DRUM KIT,
     127:GM DRUM
c = 32 BANK SEL LSB ; v = 0 - 127
c =  1 MODULATION ; v = 0 - 127
c =  5 PORTAMENTO TIME ; v = 0 - 127 *2
c =  6 DATA ENTRY MSB ; v = 0 - 127 *1
c = 38 DATA ENTRY LSB ; v = 0 - 127 *1
c =  7 MAIN VOLUME ; v = 0 - 127
c = 10 PANPOT ; v = 0 - 127
c = 11 EXPRESSION ; v = 0 - 127
c = 16 AC1 CONTROLLER ; v = 0 - 127 *2
c = 64 SUSTAIN SWITCH ; v = 0-63:OFF , 64-127:ON
c = 65 PORTAMENTO SWITCH ; v = 0-63:OFF , 64-127:ON *2
c = 66 SOSTENUTO ; v = 0-63:OFF , 64-127:ON
c = 67 SOFT PEDAL ; v = 0-63:OFF , 64-127:ON
c = 71 HARMONIC CONTENT ; v = 0:-64  -  64:0  -  127:+63
c = 72 RELEASE TIME ; v = 0:-64  -  64:0  -  127:+63
c = 73 ATTACK TIME ; v = 0:-64  -  64:0  -  127:+63
c = 74 BRIGHTNESS ; v = 0:-64  -  64:0  -  127:+63
c = 75 SOUND CONTROLLER 6 ; v = 0:-64  -  64:0  -  127:+63
c = 76 SOUND CONTROLLER 7 ; v = 0:-64  -  64:0  -  127:+63
c = 84 PORTAMENT CONTROL ; v = 0 - 127 *2
c = 91 EFFECT SEND LEVEL 1 ; v = 0 - 127
c = 93 EFFECT SEND LEVEL 3 ; v = 0 - 127
c = 94 EFFECT SEND LEVEL 4 ; v = 0 - 127
(Only when Variation Connection = System)c = 96 DATA ENTRY INC ; v = 127 *1
c = 97 DATA ENTRY DEC ; v = 127 *1
*1 Used only to set the parameter specified by RPN
*2 Not valid for rhythm voices.
*3 When MSB is 0,126 or 127, this is 0.
   When MSB is 63, this is 0-6.
MODULATION controls the depth of vibrato.
PORTAMENTO TIME adjusts the speed of the pitch change if the Portamento Switch = ON. A setting
of 0 produces the shortest portamento time, and 127 produces the longest portamento time. This value
is valid only for the Portamento Switch (Ctr#65).
PANPOT produces change relative to the preset value of the voice, both for melody voices and for
rhythm voices.
For PORTAMENTO CONTROL, the portamento time is always fixed at 0.
EFFECT SEND LEVEL 1 controls the Reverb send.
EFFECT SEND LEVEL 3 controls the Chorus send.
EFFECT SEND LEVEL 4 controls the Variation send.
HARMONIC CONTENT adjusts the resonance specified by the Voice. This is a relative parameter, and
specifies an increase or decrease centered at 64. Higher values will produce a more distinctive tone.
For some voices, the effective range maybe less than the range of the setting.
RELEASE TIME adjusts the envelope release time specified by the Voice. This is a relative parameter,
and specifies an increase or decrease centered at 64.
ATTACK TIME adjusts the envelope attack time specified by the Voice. This is a relative parameter,
and specifies an increase or decrease centered at 64.
MIDI DATA FORMAT 
						

							50 RM1x
SOUND CONTROLLER 6 adjusts the envelope decay time specified by the Voice. This is a relative
parameter, and specifies an increase or decrease centered at 64.
BRIGHTNESS adjusts the cutoff frequency specified by the Voice. This is a relative parameter, and
specifies an increase or decrease centered at 64. Decreasing the value will make the sound more
mellow. For some voices, the effective range may be less than the range of the setting.
SOUND CONTROLLER 7 adjusts the LFO Frequency specified by the Voice. This is a relative
parameter, and specifies an increase or decrease centered at 64.
(3-2) CHANNEL MODE MESSAGES
STATUS 1011nnnn(BnH) n = 0 ~ 15 VOICE CHANNEL NUMBER
CONTROL NUMBER 0ccccccc c = CONTROL NUMBER
CONTROL VALUE0vvvvvvv v = DATA VALUE
  (3-2-1) ALL SOUND OFF (CONTROL NUMBER = 78H , DATA VALUE = 0)
Turns off the sound of all currently sounding notes on the corresponding channel. The status of
channel messages such as Note On and Hold On is also turned off.
  (3-2-2) RESET ALL CONTROLLERS (CONTROL NUMBER = 79H , DATA VALUE = 0)
Resets the values of the following controllers.
PITCH BEND CHANGE 0 (center)
MODULATION 0 (of f)
AC1 CONTROLLER 0 (minimum)
EXPRESSION 127 (maximum)
SUSTAIN SWITCH 0 (of f)
PORTAMENTO SWITCH 0 (of f)
SOSTENUTO SWITCH 0 (of f)
SOFT PEDAL 0 (of f)
NRPN Un-set status. Internal data will not change.
RPN Un-set status. Internal data will not change.
PORTAMENT CONTROL reset
The following data will not change.
PROGRAM CHANGE, BANK SELECT MSB/LSB, VOLUME, PAN, HARMONIC CONTENT,
RELEASE TIME, ATTACK TIME, BRIGHTNESS, SOUND CONTROLLER 6,SOUND
CONTROLLER 7, DRY SEND LEVEL,EFFECT SEND LEVEL 1, EFFECT SEND LEVEL 3,EFFECT
SEND LEVEL 4,PITCH BEND SENSITIBITY, FINE TUNING, COURSE TUNING
  (3-2-3) ALL NOTE OFF (CONTROL NUMBER = 7BH , DATA VALUE = 0)
Turns off all notes of the corresponding channel which are on. However if Sustain or Sostenuto are on,
the sound will continue until these are turned off.
  (3-2-4) OMNI MODE OFF (CONTROL NUMBER = 7CH , DATA VALUE = 0)
Performs the same processing as when ALL NOTE OFF is received. Sets the VOICE RECEIVE
CHANNEL to OMNI OFF and CHANNEL = 1.
  (3-2-5) OMNI MODE ON (CONTROL NUMBER = 7DH , DATA VALUE = 0)
Performs the same processing as when ALL NOTE OFF is received. Does not set OMNI ON. Sets the
VOICE RECEIVE CHANNEL to OMNI ON.
  (3-2-6) MONO (CONTROL NUMBER = 7EH , DATA VALUE = 0)
Performs the same processing as when All SOUND OFF is received, and if the 3rd byte (mono
number) is in the range 0 - 16, sets the corresponding channel to Mode 4 (m=1). If in the VOICE
MODE, Mode 2 (m=1) is also possible, according to the VOICE RECEIVE CHANNEL.
  (3-2-7) POLY (CONTROL NUMBER = 7FH , DATA VALUE = 0)
Performs the same processing as when ALL SOUND OFF is received, and sets the corresponding
channel to Mode 3. When in the VOICE MODE, Mode 1 is also possible, according to the VOICE
RECEIVE CHANNEL.
(3-3) REGISTERED PARAMETER NUMBER
STATUS 1011nnnn(BnH) n = 0 - 15 VOICE CHANNEL NUMBER
LSB 01100100(64H)
RPN LSB 0ppppppp
p = RPN LSB (Refer to the table on the following page.)MSB 01100101(65H)
RPN MSB0qqqqqqqq = RPN MSB (Refer to the table on the following page.)DATA ENTRY MSB00000110(06H)
DATA VALUE0mmmmmmm m = Data Value
DATA ENTRY LSB00100110(26H)
DATA VALUE0lllllll l = Data Value
First transmit an RPN MSB and RPN LSB to specify the parameter that is to be controlled, then use
Data Entry to set the value of the specified parameter.
RPN D.ENTRY
LSB MSB MSB LSB PARAMETER NAME DATA RANGE
00H 00H mmH --- PITCH BEND SENSITIVITY 00H - 18H (0 - 24 semitones)
01H 00HmmH llH MASTER FINE TUNE
{mmH,llH} = {00H,00H} - {40H,00H} - {7FH,7FH}(-8192*100/8192) - 0 - (+8192*100/8192)02H 00H mmH --- MASTER COARSE TUNE28H - 40H - 58H (-24 - 0 - +24 semitones)7FH 7FH --- --- RPN RESETSet to a condition in which the RPN number is unspecified.Internal settings will not change.
(3-4) NON-REGISTERED PARAMETER NUMBER
STATUS 1011nnnn(BnH) n = 0 - 15 VOICE CHANNEL NUMBER
LSB 01100010(62H)
RPN LSB 0ppppppp
p = NRPN LSB (Refer to the table on the following page.)MSB 01100011(63H)
RPN MSB0qqqqqqqq = NRPN MSB (Refer to the table on the following page.)DATA ENTRY MSB00000110(06H)
DATA VALUE0mmmmmmm m = Data Value
First transmit an NRPN MSB and NRPN LSB to specify the parameter that is to be controlled, then
use Data Entry to set the value of the specified parameter.
NRPN D.ENTRY
MSB LSB MSB LSB PARAMETER NAME DATA RANGE
01H 08H mmH --- VIBRATO RATE 00H - 40H - 7FH (-64 - 0 - +63)
01H 09H mmH --- VIBRATO DEPTH 00H - 40H - 7FH (-64 - 0 - +63)
01H 0AH mmH --- VIBRATO DELAY 00H - 40H - 7FH (-64 - 0 - +63)
01H 20H mmH --- FILTER CUTOFF FREQUENCY 00H - 40H - 7FH (-64 - 0 - +63)
01H 21H mmH --- FILTER RESONANCE 00H - 40H - 7FH (-64 - 0 - +63)
01H 63H mmH --- EG ATTACK TIME 00H - 40H - 7FH (-64 - 0 - +63)
01H 64H mmH --- EG DECAY TIME00H - 40H - 7FH (-64 - 0 - +63)
01H 66H mmH --- EG RELEASE TIME 00H - 40H - 7FH (-64 - 0 - +63)(3-5) SYSTEM REAL TIME MESSAGES
  (3-5-1) ACTIVE SENSING
        S TAT U S 11111110(FEH)
Transmitted at intervals of approximately 200 msec.
Not transmitted during disk read/write operations.
Once this message is received, SENSING will begin. If neither STATUS nor DATA messages are
received for an interval longer than approximately 350 msec, the MIDI RECEIVE BUFFER will be
cleared, and all sounding notes and SUSTAIN SWITCH will be forced off. Also, data for each of the
controls will be reset to specific values.
(3-6) SYSTEM EXCLUSIVE MESSAGE
  (3-6-1)UNIVERSAL NON REALTIME MESSAGE
(3-6-1-1)GENERAL MIDI MODE ON
F0H 7EH 7FH 09H 01H F7H
The following controller values will be reset.
VOLUME 100
PAN Center
PROGRAM CHANGE 1 (Grandpno)
BANK SELECT MSB 0
REVERB DEPTH 4
PITCH BEND CHANGE 0 (center)
MODULATION 0 (off)
EXPRESSION 127 (maximum)
SUSTAIN SWITCH 0 (off)
SOSTENUTO SWITCH 0 (off)
RPN Un-set status.
PORTAMENT CONTROL reset
MIDI MASTER VOLUME 127 (maximum)
PITCH BEND SENSITIBITY 02 (2 semitones)
FINE TUNING 0
COURSE TUNING 0
(3-6-1-2)IDENTITY REQUEST (Received only)
F0H 7EH 0nH 06H 01H F7H (n is the device number, but the RM1x receives this in
Omni.)
(3-6-1-3)IDENTITY REPLY (Transmitted only)
F0H 7EH 7FH 06H 02H 43H 00H 41H ddH ddH 00H 00H 00H 01H F7H
dd;Device Number Code RM1x = 1DH,03H
  (3-6-2)UNIVERSAL REALTIME MESSAGE
(3-6-2-1) MIDI MASTER VOLUME
F0H 7FH 7FH 04H 01H llH mmH F7H
Modifies the MASTER VOLUME value.
The value of mm is used as the MIDI Master Volume (the ll value is ignored).
  (3-6-3)PARAMETER CHANGE
(3-6-3-1) MIDI MASTER TUNING
F0H 43H 1nH 27H 30H 00H 00H mmH llH ccH F7H
Modifies the MASTER TUNE value.
The values of mm and ll are used as the MIDI Master Tuning.(n and cc values are
ignored.)
T = M*200/256-100
Where T : actual tuning value (-99 - +99)
M: a one-byte value with MSB of mm bits 0-3, and LSB of
   ll bits 0-3.
(3-6-3-2) XG SYSTEM ON
11110000 F0 Exclusive status
01000011 43 YAMAHA ID
0001nnnn 1n device Number
01001100 4C Model ID
0aaaaaaa 00 Address High
0aaaaaaa 00 Address Mid
0aaaaaaa 7E Address Low
00000000 00 Data
11110111 F7 End of Exclusive
When ON is received, controllers will be reset and all Multi Part and Effect data of the
attached table will be reset to the XG default values.
(3-6-3-3) XG PARMETER CHANGE
11110000 F0 Exclusive status
01000011 43 YAMAHA ID
0001nnnn 1n device Number
01001100 4C Model ID
0aaaaaaa aaaaaaa Address High
0aaaaaaa aaaaaaaAddress Mid
0aaaaaaa aaaaaaa Address Low
0ddddddd dddddddData
||
11110111 F7 End of Exclusive
For parameters with a Data Size of 2 or 4, the corresponding amount of data will be
transmitted.
For Addresses and Byte Counts, refer to the attached tables.
The following 3 types are received.
System Data
Multi Effect Data
Multi Part Data 
						

							51 RM1x
(4) Diagram of connections between the Controller block, Sequencer block, and
Tone Generator block     | SW2
     |-[]------ SYSTEM REALTIME MESSAGE
      | |    START FAH
      | |    CONTINUE FBH
      | |    STO P FCH FCH
      | |
      | +---- SYSTEM COMMON MESSAGE
      |    SONG POSITION POINTER F2H
      |    SONG SELECT F3H
      |
      +--------- SYSTEM EXCLUSIV MESSAGE
   SECTION CONTROL F0H 43H 7EH 00H ssH ddH F7H
   TEST ENTRY F0H 43H 10H 18H 5AH 00H F7H
   LCD HARD COPY F0H 43H 10H 18H 5AH 01H F7H
SW1 []  Input Filter
Reception can be turned on/off according to the MIDI Filter settings.
SW2 []  MIDI Control In
Reception can be turned On/Off.
SW3 []  MIDI Sync
Select whether timing will be determined by the Internal clock, or by MIDI Clock messages
received at MIDI IN.
(3) TRANSMIT/RECEIVE DATA(3-1) CHANNEL VOICE MESSAGE
Transmitted only during recording and playback.
Transmission channel can be turned On/Off and the transmit channel set for each track.
Received only during recording. All Channel are always received.
During MULTI TRACK RECORD, data of MIDI CH 0-15 will be recorded separately onto tracks 1-16.
* In the RECORDING MODE, recording is normally omni on.
However, during MULTI TRACK RECORDING, this will be omni off, and data of MIDI CH 0-15 will be
recorded separately onto tracks 1-16.
  (3-1-1) NOTE OFF
STATUS 1000nnnn(8nH) n = 0 ~ 15 TRACK CHANNEL NUMBER
NOTE NUMBER 0kkkkkkk k = 0 (C-2) ~ 127 (G8)
VELOCITY0vvvvvvv v is ignored
Only recorded.
During playback, converted into 9nH kkH 00H.
  (3-1-2) NOTE ON/OFF
STATUS 1001nnnn(9nH) n = 0 ~ 15 TRACK CHANNEL NUMBER
NOTE NUMBER 0kkkkkkk k = 0 (C-2) ~ 127 (G8)
VELOCITY0vvvvvvv(v­0) NOTE ON
00000000(v=0)NOTE OFF
  (3-1-3) POLYPHONIC KEY PRESSURE
STATUS 1010nnnn(AnH) n = 0 ~ 15 TRACK CHANNEL NUMBER
NOTE NUMBER 0kkkkkkk k = 0 (C-2) ~ 127 (G8)
VALUE0vvvvvvv v = 0 - 127
  (3-1-4) CONTROL CHANGE
STATUS 1011nnnn(BnH) n = 0 ~ 15 TRACK CHANNEL NUMBER
CONTROL NUMBER 0ccccccc
CONTROL VALUE0vvvvvvv
All Control Change messages are recorded and played back.
  (3-1-5) PROGRAM CHANGE
STATUS 1100nnnn(CnH) n = 0 ~ 15 TRACK CHANNEL NUMBER
PROGRAM NUMBER 0ppppppp p = 0 - 127
  (3-1-6) CHANNEL PRESSURE
STATUS 1101nnnn(DnH) n = 0 ~ 15 TRACK CHANNEL NUMBER
VALUE0vvvvvvv v = 0 - 127
  (3-1-7) PITCH BEND CHANGE
STATUS 1110nnnn(EnH) n = 0 ~ 15 TRACK CHANNEL NUMBER
LSB 0vvvvvvvPITCH BEND LSB 0 - 127
MSB 0vvvvvvvPITCH BEND MSB 0 - 127
(3-2) CHANNEL MODE MESSAGE
The following messages are recorded and played back.
RESET ALL CONTROLLERS    BnH 78H
LOCAL CONTROL            BnH 7AH
OMNI MODE OFF            BnH 7CH
OMNI MODE ON             BnH 7DH
MONO MODE ON             BnH 7EH
POLY MODE ON             BnH 7FH
(3-3) SYSTEM COMMON MESSAGE
These are transmitted and received as Control Messages for RM1x functions.
They are not recorded as SEQUENCE DATA .
  (3-3-1) SONG POSITION POINTER
STATUS 11110010(F2H)
LSB 0vvvvvvvSONG POSITION LSB
MSB 0vvvvvvvSONG POSITION MSB
Transmitted when you move to a different measure in the SONG PLAY Mode.
Received when not playing in the SONG PLAY mode.
  (3-3-2) SONG SELECT
STATUS 11110011(F3H)
SONG NUMBER 0sssssss        SONG NUMBER(PATTERN MODE??PATTERN
NUMBER)
In the SONG mode, this will be transmitted when a song number is changed.
In the PATTERN mode, this will be transmitted when a style number is changed.
When in the SONG mode not playing, the PATTERN mode, this message is received.
When received in the PATTERN mode, a STYLE number will change.
 Sequncer block (Sequencer part)(1) TRANSMIT FLOW       SW1 SW3
MIDI -[]---+     
  IN  | |-----   NOTE OFF 8nH
      | |-----   NOTE ON/OFF 9nH
      | |-----   KEYS AFTER TOUCH AnH
      | |-----   CONTROL CHANGE BnH
      | |-----   PROGRAM CHANGE CnH
      | |-----   CHANNEL AFTER TOUCH DnH
      | |-----   PITCH BEND CHANGE EnH
      | |
      | |----- CHANNEL MODE MESSAGE
      | |    ALL SOUND OFF BnH 78H
      | |    RESET ALL CONTROLLERS BnH 79H
      | |    LOCAL CONTROL BnH 7AH
      | |    OMNI MODE OFF BnH 7CH
      | |    OMNI MODE ON BnH 7DH
      | |    MONO MODE ON BnH 7EH
      | |    POLY MODE ON BnH 7FH
      | |
      | |----- SYSTEM EXCLUSIV MESSAGE F0H ........ F7H
      |
      | SW3
      |-[]-------- TIMING CLOCK F8H
      |
      | SW3
      |-[]------ MTC QUATER FRAME MESSAGE F1H
MIDI IN
KEYBOARD
Selected Track
Filter
REC SEQUENCER
PLAY SEQUENCER
Filter
TONE GENERATORTransmit Channel
MIDI OUT 
						

							52 RM1x
(3-4) SYSTEM REAL TIME MESSAGE
Not recorded as Sequence Data.
  (3-4-1) TIMING CLOCK
S TAT U S 11111000(F8H)
You can select whether the internal clock will be used as the Timing Clock, or whether Timing Clock
messages from the MIDI IN will be used.
Transmission/reception can be turned On/Off.
  (3-4-2) START
S TAT U S 11111010(FAH)
Transmission/Reception can be turned On/Off.
  (3-4-3) CONTINUE
S TAT U S 11111 0 11(FBH)
Transmission/Reception can be turned On/Off.
  (3-4-4) STO P
S TAT U S 11111100(FCH)
Transmission/Reception can be turned On/Off.
(3-5) SYSTEM EXCLUSIVE MESSAGE
All System Exclusive Messages are recorded and played back.
Even if time intervals existed within the actual data that was received, the entire message between F0
and F7 will be recorded into one timing location.
For playback, an interval time can be specified for each 1K bytes.
(3-6) SECTION CONTROL
11110000 F0 Exclusive status
01000011 43 YAMAHA ID
01111110 7EStyle
00000000 00 Section Control
0sssssss ssSection
0ddddddd ddOn/Off
11110111 F7 End of Exclusive
ss=08H-0FH, dd=on is received, and the PATTERN will be changed to the RM1xs sections A - P
respectively.
 Parmeter Base Address
Parameter Change
Address
(H) (M) (L) Description
SYSTEM 00 00 00 System
00 00 7E XG System On
00 00 7F All Parameter Reset
INFORMATION 01 00 00 System Information
EFFECT 1 02 01 00 E ffect1(Reverb,Chorus,Variation )
02 40 00 Reserved
::::
MULTI PART 08 00 00 Multi Part 1
:
08 0F 00 Multi Part 16
08 10 00 Reserved
::::
 MIDI Parameter  Change  table ( SYSTEM )
AddressSizeData Parameter Name Description Default
(H) (H) (H)value(H)
00 00 00 4 0000 Master Tune -102.4..+102.3[cent] 00  04  00  00
      01 ..07FF 1st bit3-0®bit15-12 (0400)
      022nd bit3-0®bit11-8 (not reset by XG or GM on)
      033rd bit3-0®bit7-4 (not reset by XG or GM on)
4th bit3-0®bit3-0
      04 1 00..7F Master Volume0..127 7F
      05 1 Not Used
      06 1 28..58 Transpose-24..+24[semitones] 40
      7D Not Used
      7E 00 XG System On 00=XG Sytem on (receive only)
      7F 00 All Parameter Reset 00=on (receive only)
TOTAL  SIZE 06
 MIDI Parameter  Change  table ( EFFECT 1)
AddressSizeData Parameter Name Description Default
(H) (H) (H)value(H)
02 01 00 2 00..7F Reverb Type MSB Refer to Ef. Parameter List 01(=HALL1)
00..7F Reverb Type LSB 00 : basic type 00
      02 1 00..7F Reverb Parameter 1 Refer to Ef. Parameter List depends on Reverb type
      03 1 00..7F Reverb Parameter 2 Refer to Ef. Parameter List depends on Reverb type
      04 1 00..7F Reverb Parameter 3 Refer to Ef. Parameter List depends on Reverb type
      05 1 00..7F Reverb Parameter 4 Refer to Ef. Parameter List depends on Reverb type
      06 1 00..7F Reverb Parameter 5 Refer to Ef. Parameter List depends on Reverb type
      07 1 00..7F Reverb Parameter 6 Refer to Ef. Parameter List depends on Reverb type
      08 1 00..7F Reverb Parameter 7 Refer to Ef. Parameter List depends on Reverb type
      09 1 00..7F Reverb Parameter 8 Refer to Ef. Parameter List depends on Reverb type
      0A 1 00..7F Reverb Parameter 9 Refer to Ef. Parameter List depends on Reverb type
      0B 1 00..7F Reverb Parameter 10 Refer to Ef. Parameter List depends on Reverb type
      0C 1 00..7F Reverb Return -°..0..+6dB(0..96..127) 40
      0D 1 01..7F Reverb Pan L63..C..R63(1..64..127) 40
TOTAL  SIZE 0E(3-7) MIDI TIME CODE(QUARTER FRAME MESSAGE)
STATUS 11110001(F1H)
0nnnxxxx
If MTC is selected as the Timing Clock, MTC Quarter Frame messages will be received.
(3-8) MIDI MACHINE CONTROL
These will be transmitted if MTC is selected as the Timing Clock.
  (3-8-1) STOP(MCS)
11110000 F0 Exclusive status
01 111111 7 FRealTime Header
01 111111 7 Fdevice ID
00000110 06 MMC Command Message
00000001 01 STOP(MCS)
11110111 F7 End of Exclusive
Transmitted when the STOP button is pressed.
  (3-8-2) DEFERRED PLAY(MCS)
11110000 F0 Exclusive status
01 111111 7 FRealTime Header
01 111111 7 Fdevice ID
00000110 06 MMC Command Message
00000011  03DEFERRED PLAY(MCS)
11110111 F7 End of Exclusive
Transmitted when the PLAY button is pressed.
  (3-8-3) LOCATE(MCP)
11110000 F0 Exclusive status
01 111111 7 FRealTime Header
01 111111 7 Fdevice ID
00000110 06 MMC Command Message
01000100  44 LOCATE(MCP)
00000110 06 Byte Count
00000001 01 TERGET Sub Command
0tthhhhh hr standard time specification with sub-frames
0cmmmmmm mn
0kssssss sc
0gifffff f r
0bbbbbbb ff
11110111 F7 End of Exclusive
Transmitted when you move between measures in the SONG mode. 
						

							53 RM1x
02 01 10 1 00..7F Reverb Parameter 11 Refer to Ef. Parameter List depends on Reverb type
      11 1 00..7F Reverb Parameter 12 Refer to Ef. Parameter List depends on Reverb type
      12 1 00..7F Reverb Parameter 13 Refer to Ef. Parameter List depends on Reverb type
      13 1 00..7F Reverb Parameter 14 Refer to Ef. Parameter List depends on Reverb type
      14 1 00..7F Reverb Parameter 15 Refer to Ef. Parameter List depends on Reverb type
      15 1 00..7F Reverb Parameter 16 Refer to Ef. Parameter List depends on Reverb type
TOTAL  SIZE  6
02 01 20 2 00..7F Chorus Type MSBRefer to Ef. Parameter List 41(=Chorus1)
00..7F Chorus Type LSB 00 : basic type 00
      22 1 00..7F Chorus Parameter 1 Refer to Ef. Parameter List depends on Chorus Type
      23 1 00..7F Chorus Parameter 2 Refer to Ef. Parameter List depends on Chorus Type
      24 1 00..7F Chorus Parameter 3 Refer to Ef. Parameter List depends on Chorus Type
      25 1 00..7F Chorus Parameter 4 Refer to Ef. Parameter List depends on Chorus Type
      26 1 00..7F Chorus Parameter 5 Refer to Ef. Parameter List depends on Chorus Type
      27 1 00..7F Chorus Parameter 6 Refer to Ef. Parameter List depends on Chorus Type
      28 1 00..7F Chorus Parameter 7 Refer to Ef. Parameter List depends on Chorus Type
      29 1 00..7F Chorus Parameter 8 Refer to Ef. Parameter List depends on Chorus Type
      2A 1 00..7F Chorus Parameter 9 Refer to Ef. Parameter List depends on Chorus Type
      2B 1 00..7F Chorus Parameter 10 Refer to Ef. Parameter List depends on Chorus Type
      2C 1 00..7F Chorus Return -°..0..+6dB(0..96..127) 40
      2D 1 01..7F Chorus Pan L63..C..R63(1..64..127) 40
      2E 1 00..7F Send Chorus To Reverb -°..0..+6dB(0..96..127) 00
TOTAL  SIZE  0F
02 01 30 1 00..7F Chorus Parameter 11 Refer to Ef. Parameter List depends on Chorus Type
      31 1 00..7F Chorus Parameter 12 Refer to Ef. Parameter List depends on Chorus Type
      32 1 00..7F Chorus Parameter 13 Refer to Ef. Parameter List depends on Chorus Type
      33 1 00..7F Chorus Parameter 14 Refer to Ef. Parameter List depends on Chorus Type
      34 1 00..7F Chorus Parameter 15 Refer to Ef. Parameter List depends on Chorus Type
      35 1 00..7F Chorus Parameter 16 Refer to Ef. Parameter List depends on Chorus Type
TOTAL  SIZE  6
02 01 40 2 00..7F Variation Type MSB Refer to Ef. Parameter List 05(=DELAY L,C,R)
00..7F Variation Type LSB 00 : basic type 00
      42 2 00..7F Variation Param 1 MSB Refer to Ef. Parameter List depends on vari. type
00..7F Variation Param 1 LSB Refer to Ef. Parameter List depends on vari. type
      44 2 00..7F Variation Param 2 MSB Refer to Ef. Parameter List depends on vari. type
00..7F Variation Param 2 LSB Refer to Ef. Parameter List depends on vari. type
      46 2 00..7F Variation Param 3 MSB Refer to Ef. Parameter List depends on vari. type
00..7F Variation Param 3 LSB Refer to Ef. Parameter List depends on vari. type
      48 2 00..7F Variation Param 4 MSB Refer to Ef. Parameter List depends on vari. type
00..7F Variation Param 4 LSB Refer to Ef. Parameter List depends on vari. type
      4A 2 00..7F Variation Param 5 MSB Refer to Ef. Parameter List depends on vari. type
00..7F Variation Param 5 LSB Refer to Ef. Parameter List depends on vari. type
      4C 2 00..7F Variation Param 6 MSB Refer to Ef. Parameter List depends on vari. type
00..7F Variation Param 6 LSB Refer to Ef. Parameter List depends on vari. type
      4E 2 00..7F Variation Param 7 MSB Refer to Ef. Parameter List depends on vari. type
00..7F Variation Param 7 LSB Refer to Ef. Parameter List depends on vari. type
      50 2 00..7F Variation Param 8 MSB Refer to Ef. Parameter List depends on vari. type
00..7F Variation Param 8 LSB Refer to Ef. Parameter List depends on vari. type
      52 2 00..7F Variation Param 9 MSB Refer to Ef. Parameter List depends on vari. type
00..7F Variation Param 9 LSB Refer to Ef. Parameter List depends on vari. type
      54 2 00..7F Variation Param 10 MSB Refer to Ef. Parameter List depends on vari. type
00..7F Variation Param 10 LSB Refer to Ef. Parameter List depends on vari. type
      56 1 00..7F Variation Return -°..0..+6dB(0..96..127) 40
      57 1 01..7F Variation Pan L63..C..R63(1..64..127) 40
      58 1 00..7F Send Variation To Rev. -°..0..+6dB(0..96..127) 00
      59 1 00..7FSend Variation To Cho. -°..0..+6dB(0..96..127) 00
      5A 1 00..01 Variation Connection 0:insertion,1:system 00
      5B 1 00..1F Variation Part part1..32(0..31),off(127) 7F
      5C 1 01..7F MW Variation Ctrl Depth -63..+63 00
      5D 1 01..7F PB Variation Ctrl Depth -63..+63 00
      5E 1 01..7F AT Variation Ctrl Depth -63..+63 00
      5F 1 01..7F AC1 Variation CtrlDepth -63..+63 00
      60 1 01..7F AC2 Variation CtrlDepth -63..+63 00
TOTAL  SIZE 21
02 01 70 1 00..7F Variation Parameter 11 option Parameter depends on vari. type
      71 1 00..7F Variation Parameter 12 option Parameter depends on vari. type
      72 1 00..7F Variation Parameter 13 option Parameter depends on vari. type
      73 1 00..7F Variation Parameter 14 option Parameter depends on vari. type
      74 1 00..7F Variation Parameter 15 option Parameter depends on vari. type
      75 1 00..7F Variation Parameter 16 option Parameter depends on vari. type
TOTAL  SIZE  6
 MIDI Parameter  table ( MULTI EQ )
AddressSizeData Parameter Name Description Default
(H) (H) (H)value(H)
02 40 00 1 Not Used
      01 1 28..58 Low Boost Gain -24dB..+24dB 40(0dB)
      02 1 04..28 low Boost Frequency 50Hz..2.0KHz0c(80Hz)
      03 1 Not Used
      04 1 Not Used
      05 1 Not Used
      06 1 Not Used
      07 1 Not Used
      08 1 Not Used
      09 1 Not Used
      0A 1 Not Used
      0B 1 Not Used
      0C 1 Not Used
      0D 1 Not Used
      0E 1 Not Used
      0F 1 Not Used
      10 1 Not Used
      11 1 Not Used
      12 1 Not Used
      13 1 Not Used
      14 1 Not Used
      15 1 Not Used
TOTAL  SIZE 15
 MIDI Parameter  Change  table ( MULTI PART )
AddressSizeData Parameter Name Description Default
(H) (H) (H)value(H)
08 nn 00 1 Not Used
   nn 01 1 00..7F Bank Select MSB0..127
   nn 02 1 00..7F Bank Select LSB0..127 00 (except part 10), 7F(part 10)
   nn 03 1 00..7F Program Number1..128 00 
						

							54 RM1x
   nn 04 Not Used
   nn 05 1 00..01 Mono/Poly  Mode 0:mono,1:poly 01
   nn 06 1 00..02 Same Note Number0:single 01
Key On Assign 1:multi
2:inst (for DRUM)
   nn 07 Not Used
   nn 08 1 28..58 Note Shift -24..+24[semitones] 40
   nn 09 2 00..FF Detune -12.8..+12.7[Hz] 08  00
   nn 0A1st  bit3..0®bit7..4(80)
2nd bit3..0®bit3..0
   nn 0B 1 00..7F Volume0..127 64
   nn 0C 1 00..7F Velocity Sense Depth0..127 40
   nn 0D 1 00..7F Velocity Sense Offset0..127 40
   nn 0E 1 00..7F Pan 0:random 40
L63..C..R63(1..64..127)
   nn 0F 1 00..7F Note Limit Low C-2..G8 00
   nn 10 1 00..7F Note Limit High C-2..G8 7F
   nn 11 1 00..7FDry Level 0..127 7F
   nn 12 1 00..7F Chorus Send0..127 00
   nn 13 1 00..7F Reverb Send0..127 28
   nn 14 1 00..7F Variation Send0..127 00
   nn 15 1 00..7F Vibrato Rate -64..+63 40
   nn 16 1 00..7F Vibrato Depth -64..+63 40
   nn 17 1 00..7F Vibrato Delay -64..+63 40
   nn 18 1 00..7F Filter Cutoff Frequency -64..+63 40
   nn 19 1 00..7F Filter Resonance -64..+63 40
   nn 1A 1 00..7F EG Attack Time -64..+63 40
   nn 1B 1 00..7F EG Decay Time -64..+63 40
   nn 1C 1 00..7F EG Release Time -64..+63 40
   nn 1D 1 28..58 MW Pitch Control -24..+24[semitones] 40
   nn 1E 1 00..7F MW Filter Control -9600..+9450[cent] 40
   nn 1F 1 00..7F MW Amplitude Control -64..+63 40
   nn 20 1 00..7F MW LFO PMod Depth0..127 0A
   nn 21 1 00..7F MW LFO FMod Depth 0..127 00
   nn 22 1 00..7F MW LFO AMod Depth0..127 00
   nn 23 1 28..58 Bend Pitch Control -24..+24[semitones] 42
   nn 24 1 00..7F Bend Filter Control -9600..+9450[cent] 40
   nn 25 1 00..7F Bend Amplitude Control -64..+63 40
   nn 26 1 00..7F Bend LFO PMod Depth0..127 00
   nn 27 1 00..7F Bend LFO FMod Depth0..127 00
   nn 28 1 00..7F Bend LFO AMod Depth0..127 00
TOTAL SIZE  29
   nn 30 1 Not Used
   nn 31 1 Not Used
   nn 32 1 Not Used
   nn 33 1 Not Used
   nn 34 1 Not Used
   nn 35 1 Not Used
   nn 36 1 Not Used
   nn 37 1 Not Used
   nn 38 1 Not Used
   nn 39 1 Not Used
   nn 3A 1 Not Used
   nn 3B 1 Not Used
   nn 3C 1 Not Used
   nn 3D 1 Not Used
   nn 3E 1 Not Used
   nn 3F 1 Not Used
   nn 40 1 Not Used
   nn 41 1 Not Used
   nn 42 1 Not Used
   nn 43 1 Not Used
   nn 44 1 Not Used
   nn 45 1 Not Used
   nn 46 1 Not Used
   nn 47 1 Not Used
   nn 48 1 Not Used
   nn 49 1 Not Used
   nn 4A 1 Not Used
   nn 4B 1 Not Used
   nn 4C 1 Not Used
   nn 4D 1 Not Used
   nn 4E 1 Not Used
   nn 4F 1 Not Used
   nn 50 1 00..7F CAT LFO PMod Depth0..127 00
   nn 51 1 00..7F CAT LFO FMod Depth0..127 00
   nn 52 1 00..7F CAT LFO AMod Depth0..127 00
   nn 53 1 Not Used
   nn 54 1 Not Used
   nn 55 1 Not Used
   nn 56 1 Not Used
   nn 57 1 Not Used
   nn 58 1 Not Used
   nn 59 1 Not Used
   nn 5A 1 Not Used
   nn 5B 1 Not Used
   nn 5C 1 Not Used
   nn 5D 1 Not Used
   nn 5E 1 Not Used
   nn 5F 1 Not Used
   nn 60 1 Not Used
   nn 61 1 Not Used
   nn 62 1 Not Used
   nn 63 1 Not Used
   nn 64 1 Not Used
   nn 65 1 Not Used
   nn 66 1 Not Used
   nn 67 1 00..01 Portamento Switch o ff/on 00
   nn 68 1 00..7FPortamento Time 0..127 00
   nn 69 1 00..7FPitch EG Initial Level -64..+63 40
   nn 6A 1 00..7F Pitch EG Attack Time -64..+63 40
   nn 6B 1 00..7F Pitch EG Release Level -64..+63 40
   nn 6C 1 00..7F Pitch EG Release Time -64..+63 40