Yamaha Projector Dpx 830 User Manual

17
To stop projecting:
1. Press the STANDBY/ON () button on the projector or the STANDBY ( ) button on the remote control.
 A confirmation message is displayed.
 To cancel the procedure, wait a while or press the MENU button.
2. Press the STANDBY/ON () button on the projector or the STANDBY ( ) button on the remote control again.
 The lamp goes out and the projector goes into a cooling period. In this condition, the POWER indicator turns red and the STATUS 
indicator blinks green.
3. Wait about one...

18
Examples of the aspect ratio
You can change the aspect ratio of the input video signal (or the ratio of width to height of the image). Display pattern changes according to the  
setting of SCREEN ASPECT in the INITIAL menu. The following table is in the case of 16:9 screen. Change the setting according to the type 
of the input video signal.
*1:Available only when the input signal is 480p or 576p. *1:When ASPECT is set to SUBTITLE ZOOM or ZOOM, display position can be changed with  the    or   button...

19
◆Viewing computer images
Preparation:
 Always remove the lens cap before operating the projector.
 Turn on the power of the connected computer.
1. Confirm the POWER indicator lights up red.
 If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotating and the STANDBY/ON 
button may not work after the power cable is plugged. (The STATUS indicator blinks green.) After the fan stops rotating, press the 
STANDBY/ON button to turn back on the POWER...

20
To stop projecting:
1.  Press the STANDBY/ON () button on the projector or the STANDBY ( ) button on the remote control.
 A confirmation message is displayed.
 To cancel the procedure, wait a while or press the MENU button.
2. Press the STANDBY/ON () button on the projector or the STANDBY ( ) button on the remote control again.
 The lamp goes out and the projector goes into a cooling period. In this condition, the POWER indicator turns red and the STATUS 
indicator blinks green.
3. Wait about one...

21
◆Menu overview
Menus are not displayed when no signal is received by the projector.
After selecting the items marked with  , press the ENTER button.
*1: Not available with certain signals.
*2: The defaul value and the setting range differ depending on the input signal. 
*3: See next page for availability and unavailability.
IMAGE GAMMA DEFAULT
DYNAMIC
CINEMA
STANDARD
CUSTOM1    , CUSTOM2± 30
± 30CONTRAST
NATIVEBRIGHTNESS
HIGH
± 10
± 10
± 5
ON, OFFMID
COLOR TEMP.
LOW
CUSTOM
GAMMA - CUSTOM1
REFERENCE...

22
How to set the menus
Following describe how to set AUTO POWER OFF time as an 
example.
1. Press the MENU button.
 If no signal is input, the menu does not appear. 
2. Press the   or   button to select a menu to use.
 SETUP menu is selected in this example.
3. Press the ENTER button (or   button).4. Press the   or   button to select an item to adjust. 
5. Set the selected item by pressing the   or   button. 
To exit from the menu:
6. Press the MENU button several times.
Important
 If the MENU button...

23
◆Menu settings
The following items in the menus enable you to customize this projector.
1. IMAGE menu
 DEFAULT depends on the two signal types below:
1. Video signals (TV50, TV60, 480i/p, 576i/p, 720p50/60, 1080i50/60)
2. Computer signals (VGA, XGA, etc.)
See page 40 for a complete listing for the signal specifications.
 Memory function saves up to 3 patterns of the IMAGE menu for each input terminal (see page 30).
 BrilliantColor
TM  uses BrilliantColorTM  technology of Texas Instruments of USA....

24
2. SETUP menu
 Do not change the setting of the LAMP MODE frequently. This could damage the lamp. 
 To exit from the TEST PATTERN, press any buttons on the remote control. 
SETUP
16:9
0
CINEMA
OFF
OFF
ON
BLUE SCREEN ASPECT
VERTICAL  
LOCATION
LAMP MODE
AUTO POWER  
ON
AUTO POWER  
OFF
SPLASH  
SCREEN
HIDE SCREEN  
COLOR
FRONT/TABLE
OFF
  CROSS HATCH
LOCATION
TRIGGER OUT
TEST PATTERN
TV60
ITEM SETTING FUNCTION
SCREEN ASPECT 16:9, 4:3 Use to select the screen size.
VERTICAL 
LOCATION± 26 Use to adjust...

25
3. INITIAL menu
 DEFAULT depends on the two signal types below:
1. Video signals (TV50, TV60, 480i/p, 576i/p, 720p50/60, 1080i50/60)
2. Computer signals (VGA, XGA, etc.)
See page 40 for a complete listing for the signal specifications. ITEM SETTING FUNCTION
ASPECT DEFAULT The appropriate aspect ratio is automatically selected depending on the input signal. Select 
DEFAULT for normal use.
NORMAL Select to project images with an aspect ratio of 4:3.
SQUEEZE Select to project images with an aspect ratio...

26
4. SIGNAL menu
* The default value and the setting range differ depending on the input signals.
 Horizontal strips may appear on the enlarged projected image.
 When changing a horizontal or vertical position to a large extent, noise may appear.
 When you select COMPONENT as an input source, the setting of D-SUB INPUT will be changed to COMPONENT automatically.
 OVER SCAN and BLACK MASK are not available when the aspect ratio is set to SMART ZOOM (see page 18).
 OVER SCAN is not available when the...