Yamaha Mt 01 T 2005 Manual

SPECIAL TOOLS
1-12
Rod puller
90890-01437
Universal damping rod bleeding tool 
set
YM-A87034-53, 4-55
Rod puller attachment (M10)
90890-01436
Universal damping rod bleeding tool 
set
YM-A87034-53, 4-55
Ring nut wrench
90890-01268
Spanner wrench
YU-012684-59
Pivot shaft wrench
90890-01485
Frame mount insert wrench
YM-014855-13
Valve spring compressor
90890-04019
YM-040195-35, 5-40
Valve guide remover (ø6)
90890-04064
Valve guide remover (6.0 mm)
YM-04064-A5-36
Valve guide installer (ø6)
90890-04065
Valve...

SPECIAL TOOLS
1-13
Valve guide reamer (ø6)
90890-04066
Valve guide reamer (6.0 mm)
YM-040665-36
Piston pin puller set
90890-01304
Piston pin puller
YU-013045-42
Universal clutch holder
90890-04086
YM-910425-55, 5-58
Sheave holder
90890-01701
Primary clutch holder
YS-01880-A5-55, 5-57, 5-68, 
5-69, 5-77, 5-79
Yamaha bond No. 1215
90890-855055-57, 5-69, 5-78
Rotor puller
90890-01080
Stator rotor puller
YM-01080-A5-68
Pressure gauge
90890-031536-9 Tool name/Tool No. Illustration Reference pages
YU-01304 

SPECIAL TOOLS
1-14
Fuel pressure adapter
90890-03176
YM-031766-9
Digital circuit tester
90890-031746-10
Ignition checker
90890-06754
Opama pet-4000 spark checker
YM-344877-100 Tool name/Tool No. Illustration Reference pages 

SPEC
2 

2
SPECIFICATIONS
GENERAL SPECIFICATIONS........................................................................ 2-1
ENGINE SPECIFICATIONS............................................................................ 2-2
CHASSIS SPECIFICATIONS........................................................................ 2-10
ELECTRICAL SPECIFICATIONS................................................................. 2-14
TIGHTENING...

GENERAL SPECIFICATIONS
2-1
EAS20280
GENERAL SPECIFICATIONS
Model
Model 5YU1 (Europe)
5YU2 (AUS)
Dimensions
Overall length 2185 mm (86.0 in)
Overall width 790 mm (31.1 in)
Overall height 1160 mm (45.7 in)
Seat height 825 mm (32.5 in)
Wheelbase 1525 mm (60.0 in)
Ground clearance 143 mm (5.63 in)
Minimum turning radius 3200 mm (126.0 in)
Weight
With oil and fuel 259.0 kg (571 lb)
Maximum load 202 kg (445 lb) 

ENGINE SPECIFICATIONS
2-2
EAS20290
ENGINE SPECIFICATIONS
Engine
Engine type Air cooled 4-stroke, OHV
Displacement 1670.0 cm³ (101.90 cu.in)
Cylinder arrangement V-type 2 cylinders
Bore × stroke 97.0 × 113.0 mm (3.82 × 4.45 in)
Compression ratio 8.40 :1
Standard compression pressure (at sea level) 1200 kPa/200 r/min (170.7 psi/200 r/min) (12.0 
kgf/cm²/200 r/min)
Minimum–maximum 1000–1400 kPa (142.2–199.1 psi) (10.0–14.0 
kgf/cm²)
Starting system Electric starter
Fuel
Recommended fuel Regular unleaded...

ENGINE SPECIFICATIONS
2-3
Spark plug (s)
Manufacturer/model NGK/DPR7EA-9
Manufacturer/model DENSO/X22EPR-U9
Spark plug gap 0.8–0.9 mm (0.031–0.035 in)
Cylinder head
Volume 98.60–103.60 cm³ (6.02–6.32 cu.in)
Warpage limit* 0.03 mm (0.0012 in)
Camshaft
Drive system Gear drive
Camshaft to crankcase clearance 0.050–0.084 mm (0.0020–0.0033 in)
Camshaft lobe dimensions
Intake A 38.241–38.341 mm (1.5055–1.5095 in) (cylinder 
#1)
38.243–38.343 mm (1.5056–1.5096 in) (cylinder 
#2)
Limit 38.141 mm (1.5016 in)...

ENGINE SPECIFICATIONS
2-4
Valve, valve seat, valve guide
Valve clearance (cold)
Intake 0.00–0.04 mm (0.0000–0.0016 in)
Exhaust 0.00–0.04 mm (0.0000–0.0016 in)
Valve dimensions
Valve head diameter A (intake) 33.90–34.10 mm (1.3346–1.3425 in)
Valve head diameter A (exhaust) 27.90–28.10 mm (1.0984–1.1063 in)
Valve face width B (intake) 1.300–2.300 mm (0.0512–0.0906 in)
Valve face width B (exhaust) 1.200–2.400 mm (0.0472–0.0945 in)
Valve seat width C (intake) 0.90–1.10 mm (0.0354–0.0433 in)
Limit 2.0 mm...