Yamaha Dpx 1200 User Manual

							7
Remote control
4
iINPUT button
Switches on and off the input signal selection menu display.
oLIGHT switch
Moving this switch lights the high-use AUTO (2), ESCAPE
(6), ASPECT(8) , 
 (e), MENU (y), and INPUT (i)
buttons. The light disappears if you do not perform any
operation within 10 seconds.
pHIDE button
Temporarily halts projection of the image the DPX-1200 is
currently displaying. Press again to cancel this effect.
aRemote control code switch
Selects ID-1 or ID-2 when operating two main units with one
remote control. You can set the ID for the main unit in the
menu (The default setting is ID-1).
sRemote control cable jack
Connect this jack and REMOTE IN jack on the main unit using
a cable (commercially available) to use the remote control with
a wired connection. ( page 8)
I
R
I
SV.POSA
U
T
O
PAT
TFOCUSZOOMS
E
T
T
I
N
G
ID-2
ID-1
RESETHIDESTILLS VIDEOV
ID
EOBA
D4456
123
HDMI
MEMORYINPUT
LIGHT
INPUT
MENUESCAPE
ASPECT
a
s
11_DPX-1100_E.p6511/26/04, 2:07 PM 7 
						

							8

Loading the batteries into the remote control
1. Remove the battery compartment cover.
2. Insert two batteries (AA, UM3, or R6 type), matching the polarity
markings on the batteries with those in the battery
compartment.
3. After loading the batteries, close the cover until it snaps into
place.
Warning
•If the remote control must be used closer to the main unit than normal, or does not always operate correctly, exchange the
batteries for new ones.
•Do not mix old and new, or different types of batteries.
•Remove the batteries if you do not plan to use the unit for a long time.
•If the batteries leak, dispose of them immediately, taking care not to touch the battery fluid. If the battery fluid comes into contact
with your eyes, mouth, or skin, rinse it off with water immediately and consult a doctor. Clean the battery compartment thoroughly
before installing new batteries.

Using the remote control with a wired connection
Use a 2P monaural miniplug cable (commercially available) to connect the remote control jack on the underside of the remote control to the
REMOTE IN jack on the main unit. Use the wired remote control configuration to control the DPX-1200 without having to be within range
of the remote sensor.
1
3
2
IRISV. P
OSAUTOPAT
TF
O
C
U
SZOOMSETTING
ID-2ID-1RESETHIDESTILLS VIDEOV
I
D
E
OBAD
4456123
H
D
M
IMEMORYINPUTLIGHTI
N
P
U
TMENUESCAPEA
S
P
E
C
T
HDMI
G/Y B/PB/CBR/PR/CR
INPUT A
HD/SYNC
VD
OUT IN
REMOTETRIGGER OUT
S-VIDEOVIDEO
INPUT B
RGB/YP
BPR/YCBCR
RS-232C
D4 VIDEO
11_DPX-1100_E.p6511/26/04, 2:07 PM 8 
						

							9
Remote control
4
Distance to sensor Angle to sensor
7 m 30˚ vertically and horizontally
(approximate value) (approximate value)

Limits for using the remote control
Use the remote control within the following parameters. The remote control may not function correctly if you use it outside the limits
described here.
Warning
•Bright or fluorescent light on the main unit remote sensor may inhibit the functioning of the remote control.
•Objects placed between the main unit remote sensor and the remote control may block the remote control signal and inhibit
functioning.Use within a  left/right arc of 30 degrees Use within a vertical arc of 30 degrees
HDMIG/Y B/PB/CBR/PR/CRINPUT A
HD/SYNCVDOUT IN
REMOTETRIGGER OUTS-VIDEOVIDEOINPUT B
RGB/YPBPR/YCBCRRS-232CD4 VIDEO
45RESET6 123VIDEO STILLHIDE
PATT IRIS AUTOSETTINGZOOM FOCUS V.  P O S
LIGHTBD4S VIDEOAINPUT
MEMORYHDMIINPUTMENUASPECTESCAPE
45RESET6 123VIDEO STILLHIDE
PATT IRIS AUTOSETTINGZOOM FOCUS V. POS
LIGHTBD4S VIDEOAINPUT
MEMORYHDMIINPUTMENUASPECTESCAPE
11_DPX-1100_E.p6511/26/04, 2:07 PM 9 
						

							10
Before projection, install the main unit and a screen, connect the main unit to an AV component or computer, and adjust the projection image.
You can begin projection as soon as installation is complete.
Refer to the sections below for information on how to install the main unit to suit your viewing environment.

If you have not installed the main unit or screen
• Immediately after purchase, when you have not installed either the main unit or a screen.
• When moving the main unit and screen to a new location.

If you have installed the main unit and screen, and connected a
source component
• You have installed the main unit and screen, and connected source components.
• You are using the main unit in a previously installed location with previously connected source components.

If you have installed the main unit and screen, but not connected
any image playback components
• You have installed the main unit and screen, but not connected any source components.
• You are using the main unit in a previously installed location, and wish to change the component you use as a signal source.
You do not need to carry out step 3 or step 4 if you
do not want to adjust the projection image. If the
unit does not project the image correctly, it may not
be connected correctly. In this case, carry out this
procedure starting from step 2.
STEP3
Select an image and
project.
 page 12 - 21
• The image is used
for adjusting the
image position
and focus.
STEP4
Adjust the
projection image.
 page 22 - 40
• Use the menu to
adjust projection
details.Projection
preparations
complete
STEP2
Connect AV
components or a
computer to the
main unit.
 page 48
STEP3
Select an image and
project.
 page 12 - 21
• The image is used
for adjusting the
image position
and focus.
STEP4
Adjust the
projection image.
 page 22 - 40
• Use the menu to
adjust projection
details.Projection
preparations
complete
STEP 1
Install the main unit
and screen.
 page 50
STEP3
Select an image and
project.
 page 12 - 21
• The image is used
for adjusting the
image position
and focus.
STEP2
Connect AV
components or a
computer to the
main unit.
 page 48Projection
preparations
complete
5Preparation
STEP4
Adjust the
projection image.
 page 22 - 40
• Use the menu to
adjust projection
details.
11_DPX-1100_E.p6511/26/04, 2:07 PM 10 
						

							11
Prepararion
5
Step2
Connect an AV component or computer
• Connect AV  components
• Connect a computer   page 48
Step3
Turn the power on and selecting an
image for projection
• Turn on the projector power
• Begin playback of the input image
• Select an input signal
• Select a projection image aspect
• Adjust the image
Focus/Vertical and Horizontal position/Size/Iris
 page 12 - 21
Step1
Set up the projector and screen
• Install the projector
• Install the screen   page 50
Only adjust these
parameters when
necessary.  It is not
necessary to adjust these
settings once you have set
them initially.Step4
Use the menu to adjust the image quality and
other parameters
• Image quality: Set image quality details
• Signal setting: Set input signal details
• Default settings: Set the default settings for everyday use
• Installation settings: Set to suit your viewing environment   page 22 - 40
11_DPX-1100_E.p6511/26/04, 2:07 PM 11 
						

							12
Checking installation and connections

Pre-operation check
Prior to projection, adjust settings to suit the location of the main unit and screen, and the input signal you are using.
However, there is usually no need to adjust any settings if you have not changed the installation location or components since the last time
you used this unit. Check settings and connections only when the unit does not appear to project images correctly.
PHONO
DVRSTANDBY
/ONPURE DIRECT
2CH/MULTI CHSPEAKERSVIDEO AUXREC OUT/ZONE 2INPUT MODESOURCE/REMOTEDVD DTV/LD
MD/TAPECD-R
TUNERCDVIDEO AUX VCR 2 VCR 1SAT CABLEABSTRAIGHT
EFFECT MULTI CH
INPUTDSP
PROGRAMBALANCETONE
CONTROLVOLUMEINPUT SELECTORMULTI JOGSILENT OPTIMIZER
MICPHONESOPTICAL
R
AUDIO
L VIDEO
S VIDEO
Is the main unit power
turned on?Main unit
Are the components connected correctly?
“Connecting to AV components”
 page 48
Image source component
Is the source component power
turned on?
For an explanation of detailed settings, see “Menu”.   page 22 - 40
Check installation and connections
Select an image for projection and image adjustment
Projection preparations complete
Turn on the projector power.
Begin playback of the source image for adjustment.
Select a projection image.
(Select an input signal and projection image aspect.)
Adjust focus and vertical/ horizontal positioning.
6Projection
Prior to projection, check that the main unit and screen are correctly installed, and that source components are connected correctly.
To project images, carry out the following procedure.
Is the screen installed correctly?
 “Setting up the projector and screen”
 page 50
12_DPX-1100_E.p6511/26/04, 1:47 PM 12 
						

							13
Projection
6 
Turning the power on
Always remove the lens cap before operating the main unit.
Turning the projector power on
1. Insert the supplied power cable
firmly into the AC inlet at the rear
of the main unit, then insert the
plug into an AC outlet.
The STANDBY/ON indicator lights orange.
2. Press the STANDBY/ON button
(the 
 button on the remote
control).
The indicator blinks green and the lamp
lights up in preparation for projection. After
approximately 35 seconds, the indicator
changes from blinking to solid green,
indicating that the unit is ready to project.
Warning
• Do not remove the power cable while the STANDBY/ON indicator is blinking green or
lit steady green. This could damage the lamp or reduce lamp life.
HDMI
G/Y B/PB/CBR/PR/CRINPUT A
HD/SYNCVD
OUT IN
REMOTETRIGGER OUTS-VIDEOVIDEOINPUT B
RGB/YPBPR/YCBCRRS-232CD4 VIDEO
STANDBY/ON
SETTING
LAMP COVER TEMP FAN PATTERN
ESCAPEMENU
INPUT ASPECT
STANDBY/ON
indicator
AC inlet
INPUT
MENU
PATT IRIS AUTOSETTING
ASPECTZOOM FOCUS V. POS
ESCAPE
STANDBY/ON
SETTING
LAMP COVER TEMP FAN PATTERN
ESCAPEMENU
INPUT ASPECT
Remote Control Main unit
 button     STANDBY/ON button
12_DPX-1100_E.p6511/26/04, 1:47 PM 13 
						

							14
1. Press the STANDBY/ON button.
A confirmation message appears on the
screen.

Placing the DPX-1200 in standby mode
2. If you wish to place the DPX-1200
in standby mode, press the
STANDBY/ON button again.
The lamp changes to a half lit state, and the
fan activates for 2 minutes to cool the lamp.
During this time, the STANDBY/ON
indicator blinks orange, and pressing
STANDBY/ON does not turn main unit
power on again. When the unit finishes
cooling, the fan stops, and the STANDBY/
ON indicator turns orange.
Memo
•The lamp may blink when half lit. This is not a defect.
Warning
•Do not remove the power cable while the STANDBY/ON indicator is blinking green
or when the fan is activated. This could damage the lamp or reduce lamp life.
•If you do not plan to use the main unit for a long period of time, attach the lens cap
and remove the plug from the AC outlet.
•Condensation may appear on the unit if the temperature of the surrounding
environment changes quickly. Condensation may also cause the projected image to
be cloudy. Place the unit in standby mode until the condensation disappears.
Switching the unit on when condensation is present may damage the unit.
Turning the projector power on
AC inlet
Press again to enter standby.
HDMI
G/Y B/PB/CBR/PR/CRINPUT A
HD/SYNCVD
OUT IN
REMOTETRIGGER OUTS-VIDEOVIDEOINPUT B
RGB/YPBPR/YCBCRRS-232CD4 VIDEO
INPUT
MENU
PATT IRIS AUTOSETTING
ASPECTZOOM FOCUS V. POS
ESCAPE
STANDBY/ON
SETTING
LAMP COVER TEMP FAN PATTERN
ESCAPEMENU
INPUT ASPECT
Remote Control Main unit
 button     STANDBY/ON button
12_DPX-1100_E.p6511/26/04, 1:47 PM 14 
						

							15
Projection
6 
Selecting using the INPUT button
Press the INPUT button to select an input signal from a source component. Choose from the following:
Projection image signal
Selecting an input signal
Selects component video signals received from AV components connected to the VIDEO jack.
Selects S-Video signals received from AV components connected to the S VIDEO jack.
• Component : Selects component signals received from the INPUT A BNC jacks.
• RGB PC : Selects RGB signals received from computers connected to the INPUT A  BNC jacks.
• RGB TV : Selects RGB signals received from AV components connected to the INPUT A BNC jacks.
• Component : Selects component signals received from the INPUT B D-sub 15 pin jack.
• RGB PC : Selects RGB signals received from computers connected to the INPUT B D-sub 15 pin jack.
• RGB TV : Selects RGB signals received from AV components connected to the INPUT B D-sub 15 pin jack.
• Auto : Signals input to the HDMI jack from AV components (automatically distinguishes between
component and RGB signals).
• Component : Selects digital component signals received from AV components connected to the HDMI jack.
• RGB TV : Selects digital RGB signals received from AV components connected to the HDMI jack.
Selects component signals received from AV components connected to the D4 VIDEO jack.
INPUT SIGNAL
VIDEO
S VIDEO
INPUT A
INPUT B
HDMI
D4 VIDEO
12_DPX-1100_E.p6511/26/04, 1:47 PM 15 
						

							16

Selecting an input signal
1. Press the INPUT button.
The input signal selection menu appears on
the display.
4. Select an appropriate setting
from  [Component], [RGB PC], or
[RGB TV] and press the 
 button
to confirm the setting. 3. Press the + button to open the
submenu. 2. Use the h or g buttons to select
an input signal, then press the  
button.
The 
 mark to the right of the input signal
name indicates that there is a submenu
available for selection.
Input signal
VIDEO
S VIDEO
INPUT A
INPUT B
HDMI
D4
Input signal
VIDEO
S VIDEO
INPUT A
INPUT B
HDMI
D4
Input signal
VIDEO
S VIDEO
INPUT A
INPUT B
HDMI
D4
Component
RGB PC
RGB TV
Input signal
VIDEO
S VIDEO
INPUT A
INPUT B
HDMI
D4
Warning
•You can select [Component], [RGB PC], or [RGB TV] for INPUT A and INPUT B, or
[Auto], [Component], or [RGB TV] for HDMI, from the submenu. If you do not select a
setting, the unit continues to use the setting from the last signal it received. To
change this setting, carry out the following procedure.
Memo
•If you set your laptop or notebook computer to display on its built-in display and on
an external monitor simultaneously, the main unit may not project the image
correctly. In this case, set your computer to display on the external monitor only.
Refer to your computer’s operating instructions for further details.
STANDBY/ON
SETTING
LAMP COVER TEMP FAN PATTERN
ESCAPE MENU
INPUT ASPECT
45
RESET
6 123
VIDEO STILLHDMI
PATT IRIS AUTOSETTINGZOOM FOCUS V. POS
LIGHT
BD4S VIDEOA
INPUT
MEMORY
DVI
INPUT
MENU
ASPECT
ESCAPE
+ button Remote cotrol Main unit
 button
INPUT button
Cursor button
12_DPX-1100_E.p6511/26/04, 1:47 PM 16