Yamaha Dpx 1200 User Manual

							57
Reference
11 
 Replacing the lamp
The lamp used as a light source in the DPX-1200 is a consumable item which will gradually lose its brightness during the course of use. It is
advisable to replace the lamp when running time has exceeded 2000 hours.
You can check the lamp running time in the [Lamp Running Time] in the [Initial] menu group of the Menu screen. The LAMP warning
indicator will blink when running time exceeds 2000 hours.
There will also be a message displayed on the screen. In this case, follow the instructions below to replace the lamp cartridge. For details on
replacement of lamp cartridges, consult the store where you purchased the DPX-1200.
Warning
•Be sure to use the replacement lamp cartridge PJL-427. Other lamp cartridges are not suitable for use in the DPX-1200.
•If replacing the lamp of the projector that has been installed to the ceiling, you should remove the projector from the ceiling before
replacing the lamp.
•Before starting to replace the lamp cartridge, turn off the power, disconnect the power cable after the fan has completely stopped,
and wait at least one hour for the lamp to cool down.
•Do not remove any other screws than those specified in the following steps.
•The gases inside the lamp contain mercury vapor. Be careful the lamp may break if it gets old or overtasked. The life of a lamp
differs depending on operation environments.
1. Loosen the lamp cover screws.
2. Remove the lamp cover.
3. Loosen the screws of the lamp cartridge.
4. Grip the handle and pull the lamp cartridge to remove it.
5. Insert the new lamp cartridge by reversing the above steps, and tighten
the screws to fix it into place.
6. Replace the lamp cover and secure it with the screws.
The lamp will not turn on if the cover is not securely fastened. Take care to
attach it firmly in place.
7. Connect the unit to the power outlet, turn the unit on, and reset [Lamp
Running Time] on the [Initial] group in the menu. ( page 38)
Maintenance
Lamp cover screws
14_DPX-1100_E.p6511/26/04, 1:57 PM 57 
						

							58
Troubleshooting
CauseRemedyProblem
Image is unstable.
The image becomes
cloudy.
Cannot adjust focus or
zoom, or the vertical
position of the lens.
Remote control does
not work correctly.
There is condensation on the DPX-1200.
[Lens Adjustment Lock] in the menu is set
to ON.
The batteries are exhausted.
The remote control sensor is not set
correctly.
There is a fluorescent lamp near the
remote control sensor being used.
The remote control code switch is
incorrectly set.
Switch the DPX-1200 power off until the
condensation disappears.
Set correctly.
Set [Lens Adjustment Lock] to off.
Press the MENU button to display the menu
and select [Setup] 
 [Lens Adjustment
Lock].
Replace both batteries with new ones.
Set correctly.
Press the MENU button to display the menu
and select [Setup] 
 [Remote Control
Sensor].
Turn off the remote control sensor near the
fluorecent lamp, and use the other remote
sensor.
Set the remote control code switch to the
same ID number as the setting on the
“REMOTE CONTROL ID” in the setting menu.
The connection cables are not correctly
attached to the connectors.Correctly connect the cables to the
appropriate connectors.
The DPX-1200 does not
turn on.The power cable is not plugged in.
You attempted to turn on The DPX-1200
immediately after turning it off.
The filter cover is not correctly attached.
The lamp cover is not correctly attached.
Wait for approximately two minutes.

•
To protect the lamp, you cannot turn on
power for two minutes after you turn it off.
Plug the power cable in firmly.
Correctly attach the filter cover.
Correctly attach the lamp cover.
No picture.The lens cover has not been removed.
The DPX-1200 is not correctly connected
to the other components.
The input signal has not been correctly
selected.
The picture is turned off.
The computer is not set to display on the
external monitor.
Remove the lens cover.
Check the connections.
Select the correct input signal with the
INPUT button.
Press the AUTO button on the remote
control.
Use the menu to adjust the signal setting
to suit the input setting. 
 [Initial]
Press the HIDE button again to cancel the
HIDE function.
Set the computer to display on the external
monitor. (Refer to the computer operating
instructions.)
Press the FOCUS button, and adjust the
focus.
Adjust the projection angle and direction,
and the height of the DPX-1200.
Picture is blurred.The lens is not correctly focused.
The screen and the DPX-1200 are not
facing each other directly.
14_DPX-1100_E.p6511/26/04, 1:57 PM 58 
						

							59
Reference
11
CauseRemedyProblem
Troubleshooting
FAN warning indicator
lights up.
TEMP warning indicator
lights up.
COVER warning
indicator lights up.
LAMP warning
indicator lights up or
blinks.
The fan is broken.
The temperature inside the DPX-1200 is
extremely high.
The filter cover is not correctly attached.
The lamp cover is not correctly attached.
Lamp running time has exceeded 2000
hours.
The lamp has burned out.
Contact the store where the DPX-1200 was
purchased.
Check that the ventilation slots are not
covered.
Tightly attach the filter cover.
Tightly attach the lamp cover.
Replace the lamp with a new one.
Replace the lamp with a new one.
•This unit uses a DMDTM chip for the picture display. Their highly accurate technology makes it possible to keep more than 99.99% of
effective pixels, however, unexpectedly it can produce less than 0.01% of ineffective pixels. In such a case, missing or flashing of a
few pixels can be found on the screen. These are characteristics of DMD
TM  , not mechanical problems.
14_DPX-1100_E.p6511/26/04, 1:57 PM 59 
						

							60
Message display
MessageCondition
No Signal
Memory 1—6 Now Processing
The lamps has reached its recommended
replacement time. Please replace with a new
one.
Invalid Operation
Lens Adjustment is locked.
INPUT A (Component) (Example)
Auto Sync...
Out Of Range
Unknown Format
Press again to enter standby.
The memory setting number is displayed for two seconds.
This message is displayed when the power switch is turned on if the lamp running time
exceeds 2000 hours. Press the ESCAPE button to remove the message.
This message will display for two seconds if you press the V. POS, ZOOM, or FOCUS
button when [Lens Adjustment Lock] is set to [On].
Appears in the menu operation guide when you press an invalid button during menu
operation. This message displays for two seconds.
The unit is not receiving or detecting any signal at the selected input jack. This message is
displayed together with the name of the input source selected with the INPUT button.
The input name selected by the INPUT button is displayed. It will turn off 2 seconds after
the signal has been input.
The unit is setting itself to the most appropriate configuration for the RGB signal currently
being received.
The unit is not able to decode the PC or HDMI signal currently being input.
The unit is not able to decode the video signal currently being input.
Press the STANDBY/ON button once more to place the unit in standby mode.
14_DPX-1100_E.p6511/26/04, 1:57 PM 60 
						

							61
Reference
11
LED indicator meanings
(*) This LED is also present on the front panel of the main unit.
LED indicatorState
Unlit
Lit orange
Blinking green
Meaning
Lit green
Blinking orange
Blinking red / blinking
red and orange rapidly
Unlit
Lit red
Unlit
Lit red
Unlit
Lit red
Unlit
Lit red
Blinking orange
STANDBY/ON (*)
LAMP
COVER
TEMP
FA N
Electrical fault.
Standby
Preparing for operation.
Operating
Cooling the lamp.
Blinking red: Error in the LAMP/COVER/TEMP system
Blinking red and orange rapidly: Error in the FAN system
Normal
The lamp has burned out.
Normal
The lamp cover or the filter cover is not attached correctly.
Normal
The temperature of the lamp or the interior of the case is abnormally high.
Normal
The cooling fan has broken.
The lamp running time has exceeded 2000 hours.
14_DPX-1100_E.p6511/26/04, 1:57 PM 61 
						

							62
Specifications
Usable temperature range
Usable humidity range
Power supply
Power consumption
Power consumption in standby mode
Noise level
Dimension
Weight
5 °C – 35 °C
30 % – 85 %(There should be no condensation)
AC100 – 120 V/220 – 240 V, 50/60 Hz
375 W
0.1 W – 0.2 W
30 dB(Standard mode), 28 dB(When Lamp Power Mode is set to 80)
495(W) x 192.6(H) x 465.4(D) mm
13.8 kg
• General
Wireless remote
Wired remote1 in front, 1 at rear
1 input jack, 1 output jack
Remote
TriggerRS-232C (D-sub 9 pins)
+12 V/Max 200 mA when the power is on
• Controls
• Input
HDMIDigital RGB/component signal
Projection mode
Lens
Lamp
Screen size
Brightness
Contrast
DLPTM (DMDTM) type, 1280 X 720 pixels, 0.8 inch
f=24.3 – 38.9 mm F=2.7 – 5.0, Electronic zoom(x 1.6), Electronic focus, Electronic lens shift
270 W SHP lamp
60–200 inch (16:9)
800 – 400 ANSI lm (depends on Iris Setting)
2500:1 to 5000:1 (depends on Iris Setting)
• Optical
Color system
VIDEOComposite signal1Vp-p/75 Ω, Negative sync
S-Video signal
Component signal
Component signal
RGB signal
S VIDEO
D4 VIDEO
INPUT A/INPUT  B
Y:1Vp-p/75 Ω, Negative sync
C:0.286 or 0.3Vp-p/75 Ω
Y with sync:1Vp-p/75 Ω, Negative sync
(480i, 576i, 480p, 576p)
Y with sync:1Vp-p/75 Ω, 3 values sync
(1035i, 1080i, 720p)
P
B/CB, PR/CR:0.7Vp-p/75 Ω
Y with sync:1Vp-p/75 W, Negative sync (480i, 576i, 480p, 576p)
Y with sync:1Vp-p/75 W, 3 values sync (1035i, 1080i, 720p)
P
B/CB, PR/CR:0.7Vp-p/75 Ω
G with sync:1Vp-p/75 Ω, Negative sync
(480i, 576i, 480p, 576p)
G with sync:1Vp-p/75 Ω, 3 values sync
(1035i, 1080i, 720p)
G:0.7Vp-p/75 Ω
(When using HD/VD or SYNC)
B, R:0.7Vp-p/75 Ω
HD, VD:1–5Vp-p/2.2kΩ, positive and negative sync
SYNC:2Vp-p/2.2kΩ, Negative sync (with video signals) (480i, 576i)
SYNC:0.6–5Vp-p/2.2kΩ, Negative sync (without video signals)
(480i, 576i, 480p, 576p)
NTSC, PAL, SECAM, NTSC4.43, PAL-M, PAL-N, PAL60
14_DPX-1100_E.p6511/26/04, 1:57 PM 62 
						

							• Explanation of Graphical Symbols
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to alert
you to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert you to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
1Read these instructions.
2Keep these instructions.
3Heed all warnings.
4Follow all instructions.
5Do not use this apparatus near water.
6Clean only with dry cloth.
7Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the
obsolete outlet.
10Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11Only use attachments/accessories specified by the
manufacturer.
12Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13Unplug this apparatus during lightning storms
or when unused for long periods of time.
14Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
15Be sure to allow spaces of at least 30cm above, behind and on
both sides the unit.
16Do not place the following objects on this unit:
A vessel with water in it. If the vessel falls by vibrations and
water spills, it may cause damage to the unit, and/or you may
get an electric shock.
IMPORTANT!
Please record the serial number of this unit in the space below.
Model:
Serial No.:
The serial number is located on the bottom of the unit.
Retain this Owner’s Manual in a safe place for future reference.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
  CAUTION:  TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
  COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
IMPORTANT SAFETY INSTRUCTIONS
i
OBSERVERA
Apparaten kopplas inte bort från växelströmskällan (nätet) så länge som
den är ansluten till vägguttaget, även om själva apparaten har stängts av.
ADVARSEL
Netspæendingen til dette apparat er IKKE afbrudt, sålæenge
netledningen siddr i en stikkontakt, som er t endt – også selvom der or
slukket på apparatets afbryder.
VAROITUS
Laitteen toisiopiiriin kytketty käyttökytkin ei irroita koko laitetta
verkosta.Alleen voor klanten in Nederland
Bij dit product zijn batterijen geleverd.
Wanneer deze leeg zijn, moet u ze niet
weggooien maar inleveren als KCA.
Specifications are subject to change without notice.
• This unit may interfere with reception if placed in close proximity to a radio or television receiver. Follow the instructions in this
manual to install the unit correctly.
STANDBY/ON
SETTING
LAMP COVER TEMP FAN PATTERN
ESCAPE MENU
INPUTDIGITAL CINEMA PROJECTOR DPX-1000ASPECT
HDMI
G/Y B/P
B/CBR/PR/CRINPUT A
HD/SYNC
VDOUT IN
REMOTE
TRIGGER OUT
S VIDEO
VIDEO
INPUT B
RGB/YPBPR/YCBCR
RS-232C
D4 VIDEO
465.4
18-5/16
124.6
4-7/8
119.1
4-3/5
124
4-7/8
297.4
11-3/4132.1
5-3/16
495
19-1/2
360
14-3/16
192.6
7-9/16
237.5
9-3/8
10
3/8
(257.5
10-1/8)
Dimensional drawing
63
10_DPX-1000-Cover2-3_E.p6511/26/04, 1:13 PM 1 
						

							YAMAHA  ELECTRONICS  CORPORATION,  USA  6660  ORANGETHORPE  AVE.,  BUENA  PARK,  CALIF.  90620,  U.S.A.
YAMAHA  CANADA  MUSIC  LTD.  135  MILNER  AVE.,  SCARBOROUGH,  ONTARIO  M1S  3R1,  CANADA
YAMAHA  ELECTRONIK  EUROPA  G.m.b.H.  SIEMENSSTR.  22-34,  25462  RELLINGEN  BEI  HAMBURG,  GERMANY
YAMAHA  ELECTRONIQUE FRANCE  S.A.  RUE  AMBROISE  CROIZAT  BP70  CROISSY-BEAUBOURG  77312  MARNE-LA-VALLEE  CEDEX02,  FRANCE
YAMAHA  ELECTRONICS  (UK)  LTD.  YAMAHA  HOUSE,  200  RICKMANSWORTH  ROAD  WATFORD,  HERTS  WD18 7GQ,  ENGLAND
YAMAHA  SCANDINAVIA  A.B.  J  A  WETTERGRENS  GATA  1,  BOX  30053,  400  43  VÄSTRA  FRÖLUNDA,  SWEDEN
YAMAHA  MUSIC  AUSTRALIA  PTY,  LTD.  17-33  MARKET  ST.,  SOUTH  MELBOURNE,  3205  VIC.,  AUSTRALIA
Printed in Japan     WE49620
C2004  All Rights Reserved.
DPX-1200
10_DPX-1000-Cover1-4_E.p6511/26/04, 1:10 PM 1