Yamaha Dpx 1000 User Manual

E-6
Installation

Installation methods
There are four ways to install this unit:
on a table in front of the screen.
mounted on the ceiling in front of the screen.
on a table behind a semi translucent screen.
mounted on the ceiling behind a semi translucent screen.
Set the method you use on the 4  section of the MENU described later. (see page 21.)

Place the unit on a standard height table to project and view the image
from in front of the screen. The height from the bottom of the unit to the
center of...

E-7
English
INSTALLATION

Screen and projection distance
The ideal position for mounting the main unit (Projection distance [a]) depends on the size of the screen to be used (the length of a diagonal
line across the screen). It is possible to adjust the projection distance within a preset range from Wide to Tele using the zoom function.
Additionally, it is possible to adjust the V. POS (Vertical positioning) of the image to better suit the screen. Use the information illustrated in
the figure below to...

E-8
Installation

Projection image position
Follow the instructions below to adjust the position of the projected image on the screen.

This figure shows the limits within which the zoom function can alter
projection distance in relation to the screen size. Within these limits, it is
possible to adjust the image so that it fills the screen completely. (See
page 12.)

It is possible to adjust the vertical position of the projected image on the
screen up or down by half the height of the screen.
For...

E-9
CONNECTIONS
English
DVIINPUT B
RGB/YP
BPR/YCBCRD4 VIDEOG/YB/PB/CBR/PR/CR
INPUT A
HD/SYNCVD
OUT IN
REMOTERS-232C
S-VIDEO VIDEOTRIGGER OUT
G/YR/PR/CRB/PB/CB

 Note 

• Make sure to match the Y/PB/PR or Y/CB/CR of the A/V component and this unit when connecting a component to INPUT A compo-
nent jacks. Also, refer to the operation instructions for the A/V component. HD/SYNC and VD need to be connected for RGB video
signals in some cases.
Connecting the unit
• Make sure that the power of this unit and...

E-10
DVIINPUT B
RGB/YP
BPR/YCBCRD4 VIDEOG/YB/PB/CBR/PR/CR
INPUT A
HD/SYNCVD
OUT IN
REMOTERS-232C
S-VIDEO VIDEOTRIGGER OUT
Connecting to a computer
There are three ways of connecting a computer, as listed below. Please use the correct type of cable for the connector when making connec-
tions.
Connecting the unit

 Note 

• Refer to see 2  in the menu described on page 19 for detailed settings for the type of image signal input.  DVI cable (Digital)
D-Sub monitor
cable
BNC monitor cable
Monitor output...

E-11
BASIC OPERATION
English
Basic Operations
This section describes the basic operation of the DXP-1000 once installation and connection have been completed. It is necessary to make
detailed settings in the menu described later so that the DXP-1000 is correctly set for the mounting, screen, input signals, and other condi-
tions of its installation. Follow the steps described in this section to carry out these procedures.

Turning on the power
Be sure to remove the lens cover before using this unit....

E-12
Basic Operations

Preparations for projection
Carry out the adjustments necessary to the projection image to
obtain the optimum setting for projection.

The initial setting on this unit is for projection of the image in a
line directly from the center of the lens. Where the center of the
screen is above or below the center of this line, use the V. POS
function to adjust the vertical position of the image up or down.
V. POS can adjust the image up to half the height of the screen.
1.Press the V. POS...

E-13
BASIC OPERATION
English

Select an input
Press the INPUT button to display the input selection menu on the
screen. Use the h and g to select a name from those on display and
then press the 
 to confirm your choice.
The signal settings for INPUT A, INPUT B and DVI will not
change. To change them, press the + button to open the submenu,
use the cursor buttons to select a suitable source from Component/
RGB PC/RGB TV, and confirm the selection by pressing the 
button. You can select the terminal name...

E-14
Basic Operations

Select a display aspect
Display aspect selects the type of image to display for an input signal. Press the ASPECT button and select a suitable mode. The types of
aspect mode available depend on the input signal. Additionally, this unit has an auto mode that can automatically select the correct display
aspect if the relevant information is encoded in the input signal. These modes are accessible from the display aspect area of the 2 
section of the menu described later.
1Auto (Zoom)...

E-15
BASIC OPERATION
English
Basic Operations

Other functions
STILL — freezing the image
Press the STILL button on the remote control to capture a frame
from a moving image. Press STILL once more to resume normal
projection.
HIDE — turning off the image temporarily
Press the HIDE button on the remote control to temporarily turn of
the projected image. Press the HIDE button once more to resume
normal projection.

Indicators
There are 5 indicators on the main unit that display the operating
status of the...