Yamaha Cl 5 User Guide

 Data List
38
[Conversion from actual data to bulk data]d[0-6]: actual data
b[0-7]: bulk data
b[0] = 0;
for( I=0; I

 Data List
39
4.2.3 Module Name
*1) 0:CH1 - 71:CH72
72:ST IN 1L - 87:ST IN 8R
*2) 256:MIX 1 - 279:MIX 24
*3) 512:MATRIX 1 - 519:  MATRIX 8
*4) 1024:STEREO L - 1026:STEREO C
*5)  512: will be used if the recalling or storing data is only one.
*6) 0:  GEQ1A, 1:  GEQ1B, 2:  GEQ2A, ... 36:  GEQ19A, 37:GEQ19B
38:  EFFECT GEQ1A, 39:  EFFECT GEQ1B, 
40:  EFFECT GEQ2A, ... 52:  EFFECT GEQ8A, 53:  EFFECT GEQ8B
*7) 0:Effect1- 7:Effect8
*8) 1280:CH1 - 1351:CH72
1352:ST IN 1L - 1367:ST IN 8R
*9) 0:  Premium Rack 1A,...

 Data List
40
4.4 FUNCTION CALL - LIBRARY ATTRIBUTE -4.4.1 Format (PARAMETER CHANGE)
ReceptionData will be received when [PARAMETER CHANGE Rx] is on and the Device 
number of both [Rx CH] and SUB STATUS match.
The data will be echoed when [PARAMETER CHANGE ECHO] is on.
When the message is received, the title of the specified memory/library will be 
edited.TransmissionPARAMETER CHANGE will be sent in reply to Request.
If [PARAMETER CHANGE ECHO] is on, the message will be sent as it is.
4.4.2 Format...

 Data List
41
4.5.2 Format (PARAMETER REQUEST)
ReceptionThe PARAMETER CHANGE will be sent with Device number [Rx CH] immediately 
the data is received.4.5.3 Module Name
4.6 FUNCTION CALL - COLLECTION STORE -4.6.1 Format (PARAMETER CHANGE)
TransmissionData will be transmitted with the [Device Number] in [Tx CH] when [PARAMETER 
CHANGE Tx] is on.4.6.2 Function Name
4.6.3 Module Name
4.7 FUNCTION CALL - MODULE -4.7.1 Format (PARAMETER CHANGE)
ReceptionData will be received when [PARAMETER CHANGE Rx] is on...

 Data List
42
4.8  FUNCTION CALL - CHANNEL -4.8.1 Pair ON/OFF Trigger Format (PARAMETER CHANGE)
ReceptionData will be received when [PARAMETER CHANGE Rx] is on and the Device 
number of both [Rx CH] and SUB STATUS match.
The data will be echoed when [PARAMETER CHANGE ECHO] is on.4.8.2 Module Name
*1) 0:CH1 - 71:CH72
256:MIX 1 - 279:MIX 24
512:MATRIX 1-519:MATRIX 8
4.9 LEVEL METER DATA4.9.1 Format (PARAMETER CHANGE)When transmission is enabled by receiving Request for Level Meter, the 
corresponding...

 Data List
43 Input/output characteristics
ANALOG INPUT CHARACTERISTICS
*1. Sensitivity is the lowest level that will produce an output of +4dBu (1.23V) or the nominal 
output level when the unit is set to maximum gain. (all faders and level controls are 
maximum position.)
*2. XLR-3-31 type connectors are balanced. (1= GND, 2= HOT, 3= COLD)
* In these specifications, 0dBu= 0.775 Vrms.
* All input AD converters are 24bit linear, 128times oversampling.
* +48V DC ( phantom power ) is supplied to ONI IN...

 Data List
44
I/O SLOT (1-3) CHARACTERISTICSEach I/O Slot accepts a mini-YGDAI card. Only Slot1 has a serial interface.CONTROL I/O CHARACTERISTICS
*1. Input pin: TTL level, w/ internal pull-up (47kΩ)
Output pin: Open drain output (Vmax=12V, maximum sink current/pin=75mA)
Power supply pin: Output voltage Vp=5V, Max. output current Imax=300mA
*2. 4 pin=+12V, 3 pin=GND, Lamp rating 5W. Voltage control by software.Terminal Format Level Connector
MIDIIN MIDI - DIN Connector 5P
OUT MIDI - DIN Connector 5P
WORD...

 Data List
45 Electrical Characteristics
All faders are nominal when measured. Output impedance of signal generator:150ohms
Frequency Response. 
Fs= 44.1 kHz or 48 kHz @20 Hz-20 kHz, referenced to 
the nominal output level @1 kHz

Total Harmonic Distortion. 
Fs= 44.1 kHz or 48 kHz
* Total Harmonic Distortion is measured with a 18 dB/octave filter @80 kHz
Hum & Noise. 
Fs= 44.1 kHz or 48 kHz, EIN= Equivalent Input Noise
* Hum & Noise are measured with A-weight filter.
Dynamic Range. 
Fs= 44.1 kHz or...

 Data List
46 Mixer Basic Parameters

Libraries

Input Function

Output Function

Output Port

Processor
Name
Number
To t a l
Scene Memory Preset 1 + User 300 301
Input CH Library Preset 1 + User 199 200
Output CH Library Preset 1 + User 199 200
Input EQ Library Preset 40 + User 159 199
Output EQ Library Preset 3 + User 196 199
Dynamics Library Preset 41 + User 158 199
Effect Library Preset 27 + User 172 199
GEQ Library Preset 1 + User 199 200
Premium Rack Library
Portico5033
Portico5043
U76
Opt-2A...

 Data List
47 Pin Assignment
DC POWER INPUT GPI METER (CL3/CL1 only)
Pin Signal Name Pin Signal Name
1+24V13GND
2+24V14GND
3+24V15GND
4+24V16GND
5+24V17GND
6+24V18GND
7+24V19CAUTION(+)
8 +24V 20 CAUTION(-)
9 +24V 21 DETECT A
10 GND 22 DETECT B
11 GND 23 DETECT GND
12 GND Frame GND
1
2
3 4
5 6 7 8 9
10 11 12 13 14
15
16
17 18 19 20
21
22 23
Pin Signal Name Pin Signal Name
1GPO19GPO2
2GPO310GPO4
3GPO511GND
4GND12GND
5 +5V 13 +5V
6 GPI114GPI2
7 GPI315GPI4
8GPI5
9
10
11 8
1
2
3
15
Pin Signal Name Pin Signal...