Xerox WorkCentre Pro 133 User Manual

Xerox CopyCentre/WorkCentre/WorkCentre Pro 123/128/133 User Guide 181
10 Paper and Other Media
The machine is designed to use various paper types and other media. This chapter 
provides information on loading paper and other types of media into the machine.
Loading Paper
The machine can be equipped with various paper trays. This section provides 
information on how to load paper into each type of tray.
NOTE: Make sure the side and rear paper guides on the trays are properly positioned 
to match the size...

10 Paper and Other Media 
182 Xerox CopyCentre/WorkCentre/WorkCentre Pro 123/128/133 User Guide
NOTE: To avoid jams and misfeeds, do not load paper on top of any remaining paper 
in the tray. Remove the paper, and reload it on top of the new stock loaded.
2.If required, move the paper tray 
guides further out to load the 
new stock.
To adjust the side and rear 
guides, pinch the guide lever on 
each guide and slide the guides to 
their new position.
To secure the guides in position, 
release the levers....

Loading Paper 
Xerox CopyCentre/WorkCentre/WorkCentre Pro 123/128/133 User Guide 183
6.Set the machine to detect the paper size automatically, or manually specify the 
required size. For more information, refer to Paper Size in the Setups chapter on 
page 195.
NOTE: Paper sizes detected by the machine vary depending on the Key Operator 
setting. For more information, refer to Paper Size Settings in the Setups chapter on 
page 201.
Bypass Tray (Tray 5)
The bypass tray allows you to use a variety of paper...

10 Paper and Other Media 
184 Xerox CopyCentre/WorkCentre/WorkCentre Pro 123/128/133 User Guide
Tandem Tray Module (TTM)
The Tandem Tray Module allows you to load larger amounts of paper. It consists of two 
trays.
NOTE: You cannot load custom size paper into the Tandem Tray Module.
1.Pull out the Tray 3 or Tray 4 of 
TTM.
The elevator in the tray lowers.
2.Place the paper stock tightly 
against the left rear corner of the 
tray.
NOTE: Do not load paper above the 
maximum fill line.
NOTE: Always load...

Supported Paper Sizes and Types 
Xerox CopyCentre/WorkCentre/WorkCentre Pro 123/128/133 User Guide 185
• Store paper in dry conditions, away from extreme heat or cold, such as radiators or 
open windows.
• Store paper flat on a shelf or pallet above floor level.
• Leave the paper wrapped and boxed until ready to be used.
• Re-wrap partly used packages of paper.
NOTE: Paper should not be stored in the paper trays.
Supported Paper Sizes and Types
This section lists the sizes and types of paper that can be...

10 Paper and Other Media 
186 Xerox CopyCentre/WorkCentre/WorkCentre Pro 123/128/133 User Guide
O: Available
X: Not available
8 × 10” 203.2 254.0 SEF X X O O X
LEF X X O O X
8.5 × 11” 215.9 279.4 SEF O X O O O
LEF O OOOO
8.46 × 12.4” 215.0 315.0 SEF X X O O X
8.5 × 13” 215.9 330.2 SEF O X O O O
8.5 × 14” 215.9 355.6 SEF O X O O O
11 × 15” 279.0 381.0 SEF X X O O X
11 × 17” 297.4 431.8 SEF O X O O O
A4 Cover 297.0 223.0 LEF X X O O X
9 × 11” 279.4 228.6 LEF X X O O X
16K 194.0 267.0 SEF X X O O X
LEF O X...

Supported Paper Sizes and Types 
Xerox CopyCentre/WorkCentre/WorkCentre Pro 123/128/133 User Guide 187
Non-standard Sizes
Paper SizeTray 1, 2/
Tray 3, 4 
(Two Tray 
Module)Tray 3, 4 
(TTM)Tray 5 
(Bypass)Duplex Module Finisher
Width 140 to 297 mm 
5.5 to 11.7”
Not Available89 to 297 mm
3.5 to 11.7”89 to 297 mm
3.5 to 11.7 
Not Available Length 182 to 432 mm
7.2 to 17.0”99 to 432 mm
3.9 to 17.0”127 to 432 mm 
(for Tray 5 (Bypass)) 
182 to 432 mm 
(for Tray 1–4)
Downloaded From ManualsPrinter.com Manuals 

10 Paper and Other Media 
188 Xerox CopyCentre/WorkCentre/WorkCentre Pro 123/128/133 User Guide
Supported Paper Types
The following table lists the paper types supported for each paper tray, duplex module, 
and the finisher.
O: Available
X: Not available
• Side 2 Paper: Refers to the paper already printed on one side (i.e. scrap paper).
• Transparency: When using Xerox paper backed (3R3028) (for US) or 3M Type L 
Desktop Laser (3R91334) (for EU) in low temperature and humidity (10
oC, 15%) 
select...

Xerox CopyCentre/WorkCentre/WorkCentre Pro 123/128/133 User Guide 189
11 S e t u ps
This chapter, aimed for the Key Operator, describes how to change various defaults 
preset on the machine, how to register various items such as mailboxes and 
destinations, and how to configure or change Key Operator settings.
System Settings Procedure
This section describes the basic system settings procedure. Follow the steps below.
1. Entering the System Settings Mode – page 189
2. Customizing the Settings – page 190...

11 Setups 
190 Xerox CopyCentre/WorkCentre/WorkCentre Pro 123/128/133 User Guide
2. Customizing the Settings
1.Select a desired option.
Customize the settings by 
performing operations as necessary. 
For some options, select [Change 
Settings] to change the settings or to 
enter characters through the screen 
keyboard. For information on 
keyboard entry, refer to Keyboard in the Fax/Internet Fax chapter on page 83.
System Settings
This screen allows you to select features of the settings you want to...