Home > Xerox > Projector > Xerox Projector Dp 1011 User Manual

Xerox Projector Dp 1011 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Xerox Projector Dp 1011 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 228 Xerox manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Xerox DP1011 User’s Guide16
    User Controls
    Adjust the Projector Image
    1. Press the Menu button on the Remote Control or Panel Control 
    to open the OSD.
    2. Select the All Images menu and press the Enter button.
    The All Images menu appears.
    3. Use the     keys to select the item you want, and use the
       keys to adjust the selected setting.
    4. When the new settings are what you want, press the Menu 
    button again.
    Brightness—Lightens or darkens the image. The higher the 
    number, the brighter the image.
    Contrast—Controls the degree of difference between the lightest 
    and darkest parts of the image. Adjusting the contrast changes the 
    amount of black and white in the image. The higher the number the 
    greater the contrast.
    Image Optimization—Maximizes the settings for brightness and 
    contrast, and color reproduction quality. The number ranges from 0 
    to 10.
    • Setting 10 maximizes brightness and contrast.
    • Setting 0 maximizes color reproduction quality.
    Color Temperature—Controls the color temperature of the image. 
    Higher temperatures make the screen look colder, lower 
    temperatures make the screen look warmer.
    Keystone correction—Adjust the image distortion caused by 
    tilting the projector (+/- 16 degrees).
    Zoom—Enlarges or reduces the image size. The higher the 
    number the more the image is enlarged.
    Aspect Ratio—Control the length-to-width aspect ratio for the type 
    of video source you are using. If the image seems to be distorted or 
    stretched, change the aspect ratio.
    Reset This Menu—Resets the projector’s display settings to their 
    original factory settings. Select Ye s to reset the menu. 
    						
    							Xerox DP1011 User’s Guide17
    User Controls
    Adjust the Computer Image
    1. Press the Menu button on the Remote Control or Panel Control 
    to open the OSD.
    2. Select the Computer Image menu and press the Enter button.
    The Computer Image menu appears.
    3. Use the     keys to select the item you want, and use the
       keys to adjust the selected setting.
    4. When the new settings are what you want, press the Menu 
    button again.
    Auto Image—Automatically adjust the frequency, tracking, and 
    horizontal and vertical position. For most video sources, Auto 
    Image provides the best results.
    Frequency—Changes the display data frequency to match the 
    frequency of your computer’s graphics card. If a vertical flickering 
    bar appears on the image, adjust the frequency until it disappears.
    Tracking—Synchronizes the signal timing of the display with the 
    timing of your computer’s graphics card. If the image flickers or is 
    unstable, adjust the tracking until the image is stable.
    Horizontal and Vertical Position—Moves the image left and right, 
    and up and down on the screen.
    Reset This Menu—Resets the projector’s display settings to their 
    original factory settings. Select Ye s to reset the menu. 
    						
    							Xerox DP1011 User’s Guide18
    User Controls
    Adjust the Video Image
    1. Press the Menu button on the Remote Control or Panel Control 
    to open the OSD.
    2. Select the Video Image menu and press the Enter button.
    The Video Image menu appears.
    3. Use the     keys to select the item you want, and use the
       keys to adjust the selected setting.
    4. When the new settings are what you want, press the Menu 
    button again.
    Color Saturation—Adjusts the video image from black and white 
    to fully saturated color. The higher the number, the greater the 
    color saturation.
    Sharpness—Adjusts the sharpness of the image. The higher the 
    number the sharper the image.
    Tint—Adjusts the color balance of red and green. Decreasing the 
    tint, increase the amount of green in the image. Increasing the tint 
    increases the amount of red in the image.
    Reset This Menu—Resets the projector’s display settings to their 
    original factory settings. Select Ye s to reset the menu. 
    						
    							Xerox DP1011 User’s Guide19
    User Controls
    Projector Management
    1. Press the Menu button on the Remote Control or Panel Control 
    to open the OSD.
    2. Select the Management menu and press the Enter button.
    The Management menu appears.
    3. Use the     keys to select the item you want, and use the
       keys to adjust the selected setting.
    4. When the new settings are what you want, press the Menu 
    button again.
    Menu Location—Sets the location of the menus on the screen.
    Projection Direction:
    •Front-Desktop—Projects onto an image in front of the 
    projector. The factory default setting.
    •Rear-Desktop—Projects a reversed image so you can project 
    from behind a translucent screen.
    •Front-Ceiling—Projects an image turned upside down for 
    ceiling-mounted projection.
    •Rear-Ceiling—Projects a reversed image turned upside down 
    for ceiling-mounted projection from behind a translucent 
    screen.
    Lamp Hour—Displays the lamp’s elapsed operating time (in 
    hours).
    Reset Lamp Hours—Resets the lamp’s elapsed operating time. 
    Reset this option only after installing a new lamp.
    Reset This Menu—Resets the projector’s display settings to their 
    original factory settings. Select Yes to reset the menu.
    Machine Reset—Resets the projector’s settings (except Lamp 
    Hours) on all menus to their original factory settings. Select Ye s to 
    reset all menus. 
    						
    							Xerox DP1011 User’s Guide20
    User Controls
    Adjust the PiP (Picture in Picture)
    1. Press the Menu button on the Remote Control or Panel Control 
    to open the OSD.
    2. Select the PiP menu and press the Enter button.
    The PiP menu appears.
    3. Use the     keys to select the item you want, and use the
       keys to adjust the selected setting.
    4. When the new settings are what you want, press the Menu 
    button again.
    PiP—Turns on and off the PiP function.
    PiP Location—Sets the position of the PiP screen on the display 
    screen
    PiP Switch Source—Chooses the input source of the projector on 
    the PiP screen.
    Reset This Menu—Resets the projector’s display settings to their 
    original factory settings. Select Ye s to reset the menu.
    NOTE:The OSD does not include a PiP menu in Video mode. 
    						
    							Xerox DP1011 User’s Guide21
    Maintenance
    Maintenance
    Changing the Lamp
    The projector’s lamp life is approximately 1500 hours of use. The 
    projector automatically monitors the lamp life. After 1500 hours of 
    use, the projector displays the message:
    The Lamp has been in use for over 1500 hours. You should 
    purchase a spare bulb.
    When you see this message, please contact your local reseller or 
    service center to change the lamp as soon as possible.
    Warning—To reduce the risk of personal injury, do not drop the 
    lamp module or touch the lamp bulb. The bulb may shatter and 
    cause injury if dropped.
    Warning—Lamp compartment is hot! Allow the projector to cool 
    down at least 30 minutes.
    To change the lamp module
    1. Turn off the projector’s power by pressing the power button on 
    the Remote Control or Projector Panel.
    2. Disconnect the power cord.
    3. Use a screwdriver to remove the two screws from the cover. 
    						
    							Xerox DP1011 User’s Guide22
    Maintenance
    4. Remove the cover.
    5. Remove the two screws from the lamp module.
    6. Lift up the handle and pull out the lamp module.
    7. To replace the lamp module, reverse the previous steps.
    Lamp Module 
    						
    							Xerox DP1011 User’s Guide23
    Maintenance
    Troubleshooting
    If you try the troubleshooting procedures described in this section 
    and the problem persists, you may have a malfunctioning projector. 
    Refer to the technical support card that you received with your 
    projector or contact the retailer where you purchased your 
    projector. Also visit our web site at www.xeroxprojectors.com for 
    additional technical information. 
    Problem: No image appears on the screen.
    Check for one of these possible problems:
    •Are the cables loose or not plugged in securely? Inspect 
    the cable connections. Make sure the cables are plugged in 
    securely.
    •Are any of the pins on the cables bent or broken? Inspect 
    the pins on the cable plugs to make sure none of the pins are 
    bent or broken.
    •Is the projection lamp securely installed? Check that the 
    projection lamp is securely installed, especially if you just 
    changed it. See the section “Changing the Lamp” on page 21 
    for details about the lamp installation.
    •Is the power on? Check that the projector’s power switch is 
    turned on and that the power cord is plugged in securely to a 
    working power outlet.
    •Is the lens cap still on? Make sure you have removed the 
    lens cap from the lens at the front of the projector
    Problem: The image is incorrectly displayed, or scrolls, 
    or only partially displayed.
    From the projector’s On Screen Display, select the Computer 
    Image menu and select Auto Image so the projector can 
    automatically adjust the image to provide the best possible results.
    If the image is still not projected correctly, the resolution setting of 
    your computer screen is too high (greater than 1024 x 768) and 
    you must reset it.
    For Windows 3.x:
    1. In the Windows Program Manager, click the Windows Setup 
    icon in the Main group.
    2. Verify that your display resolution setting is less than or equal 
    to 1024 x 768. 
    						
    							Xerox DP1011 User’s Guide24
    Maintenance
    For Windows 95, 98, 2000, XP:
    1. From the Windows Start menu, select Settings/Control Panel 
    and then double-click the Display icon.
    2. Select the Setting tab. 
    The Desktop Area shows the resolution setting. 
    3. Verify that the resolution setting is 1024 x 768 or less.
    If the projector is still not projecting the whole image, you will also 
    need to select another monitor display for your computer. Use the 
    following steps.
    To select another monitor display:
    1. On the Display dialog box that you opened in the steps above, 
    click the Advanced Properties button.
    2. Select the Monitor tab and click the Change button.
    3. Click Show all devices.
    4. Under the Manufacturers box, select Standard monitor types.
    5. Under the Models box, choose the resolution mode.
    6. Verify that the resolution setting of the monitor display is less 
    than or equal to 1024 x 768.
    If you are using a Notebook PC:
    1. Follow the steps above to set the resolution to 1024 x 768 or 
    less. 
    2. Switch the Notebook PC display to the external display only 
    or CRT only mode. 
    If you experience difficulty changing resolutions or your monitor 
    freezes, restart all the equipment and the projector.
    Problem: The screen of the Notebook or PowerBook 
    computer is not displaying your presentation
    If you are using a Notebook PC:
    Some Notebook PCs deactivate their own screens when a second 
    display device is attached. Please see the user’s manual that you 
    received with your Notebook PC for the steps to reactivate its 
    screen.
    If you are using an Apple PowerBook:
    1. From the Apple menu, choose Control Panels/PowerBook 
    Display.
    2. Turn on Video Mirroring.
    3. Click the Close box. 
    						
    							Xerox DP1011 User’s Guide25
    Maintenance
    Problem: The image is flickering or otherwise unstable
    Try one of these possible solutions:
    •On the On-screen display, go to the Computer Mode page 
    and select Tracking. Change the tracking until the image 
    stabilizes.
    •Change the color setting of your computer monitor. 
    Change the number of colors that your computer displays on its 
    monitor.
    Problem: Image has vertical flickering bar.
    Try one of these possible solutions:
    •On the On-screen display, go to the Computer Mode page 
    and select Frequency. Change the frequency to match the 
    frequency of the video card in your computer.
    •Reset the display mode of your graphic card to make it 
    compatible with the projector. See “Setting the Screen 
    Resolution” on page 28 for details.
    Problem: Image is our of focus.
    Try one of these possible solutions:
    •Adjust the focus ring on the projector. Turn the focus ring 
    until the image comes into focus.
    •Make sure the distance between the projector and the 
    screen is between 3.94 ft (1.2m) and 32.81 ft (10.0m). See 
    “Adjusting Projection Image Size” on page 11 for details.
    Problem: The screen is outstretched when displaying 
    16:9 DVD.
    The projector automatically detects 16:9 DVD and digitally adjusts 
    the image aspect ratio to full screen with a 4:3 default setting.
    If the screen is still outstretched, try one of these possible 
    solutions:
    •Reset your DVD player to display at a 4:3 aspect ratio. See 
    the DVD player user’s guide for the steps to adjust its aspect 
    ratio.
    •On the projector’s On-screen display, go to the Computer/
    Video Mode page and select Aspect ratio. Change the 
    aspect ratio to 4:3. 
    						
    All Xerox manuals Comments (0)

    Related Manuals for Xerox Projector Dp 1011 User Manual