Xerox Projector Dp 1011 User Manual

							Xerox DP1011 User’s Guide6
Precautions
Connection Ports
Power Connector—Plug the power cord into the projector here. 
VGA Connector—Use the VGA cable that you received with your 
projector to plug in a computer, HDTV, or component video source.
Composite Video Input Connector—Plug in your composite 
video source here, such as a DVD player or VCR. Requires a 
standard A/V connecting cable. Connect the yellow (video) plug to 
your video source and to the projector.
S-Video Input Connector—Plug in your S-Video source here, 
such as a professional-quality DVD player or VCR. Requires a 
standard S-Video connecting cable.
Remote Control Receiver—Infrared receiver that receive signals 
from the remote control. Located on both the front and rear so you 
can control the projector from either position. Do not cover or block 
this receiver.
Kensington™ Lock Slot—Slot for inserting a Kensington cable 
and lock to protect your projector from theft.
Remote Control 
Receiver
VGA connector—for 
computer (PC Analog 
signal), HDTV, or 
Component Video
S-Video Input  
Connector
Power Connector
Composite Video 
Input  Connector
Kensington™ 
Lock Slot 
						

							Xerox DP1011 User’s Guide7
Installation
Installation
Connecting the Projector
1. Make sure the projector and computer are turned off.
2. Connect one end of the VGA cable to the projector. Connect 
the other end to the VGA port on the computer.
3. Connect the projector to the other video source(s) with the 
appropriate cable(s).
4. Plug the power cord into the back of the projector and then into 
an electrical outlet.
5. Turn on the projector first, and then the computer.
Video Output
S-Video Output
VGA Cable
Power Cord
S-Video Cable
Composite Video Cable
NOTE:Your DP1011 projector works best at computer screen 
resolutions of 1024 x 768 or less. To reset the computer screen 
resolution,  see “Setting the Screen Resolution” on page 28. 
						

							Xerox DP1011 User’s Guide8
Installation
Powering On/Off the Projector
To turn on the projector power
1. Remove the lens cap.
2. Make sure that the power cord and the cables from the video 
sources are securely connected to the projector.
3. Turn on the lamp by pressing the Power button on the control 
panel or on the Remote Control.
The startup screen displays for 20 seconds and the 
Power/Standby indicator flashes green.
When the startup screen disappears, the Power/Standby 
indicator turns a steady green.
4. Turn on your video source device (computer, notebook, DVD 
player, video player, etc.). The projector detects the video 
source automatically.
If the screen displays “No Signal”, please make sure the signal 
cables are securely connected.
If you connect multiple sources at the same time, use the Source 
button on the remote control or control panel to switch among 
them.
NOTE:Turn the projector on first, then the computer.
Power
Lens cap 
						

							Xerox DP1011 User’s Guide9
Installation
To turn off the projector power
1. Press the Power button on the projector or Remote Control to 
turn off the projector lamp.
An on-screen message appears: Power off the lamp?
2. Press the Power button again to confirm.
If you don’t press the button again within five seconds, the 
message disappears and the lamp remains lit. This convenient 
design is in case you accidently press the Power button in the 
middle of a show and do not want to turn off the projector.
If you do press the Power button a second time, the 
Power/Standby indicator flashes orange for about 40 seconds. 
Then the projector automatically shuts itself down.
3. To turn on the projector again, press the Power button within 
40 seconds of the indicator flashing.
4. Disconnect the power cord.
Warning Indicator Lights
• If the Warning indicator turns red, the projector has overheated. 
The projector will automatically shut itself down.
• A Warning indicator flashing red (0.5 second intervals), 
indicates a problem with the lamp. Turn off the projector and 
disconnect the power cord from the electrical outlet, then 
contact your local dealer or our service center.
• A Warning indicator flashing red (1 second intervals), indicates 
an internal problem. Turn off the projector and disconnect the 
power cord from the electrical outlet, then contact your local 
dealer or our service center.
• A Warning indicator flashing orange, indicates high-speed 
cooling in progress. This is not an abnormal condition, and you 
can continue using the projector. NOTE:Do not turn off the projector immediately following a 
power off procedure. Let it cool down first.
Warning Indicator 
						

							Xerox DP1011 User’s Guide10
Installation
Adjusting the Projected Image
To raise the projector
1. Lift the projector up and press the elevator button.
The elevator foot pops out.
2. Press the elevator button and hold it in while raising the 
projector to the display angle you want, then release the 
elevator button to lock the elevator foot in position.
3. Rotate the tilt adjust wheel to fine-tune the display angle. The 
tilt adjust wheel is only on the back foot diagonally opposite the 
lens.
To lower the projector
1. Hold the projector with one hand, then press and hold down the 
elevator button.
2. Lower the projector, then release the elevator button to lock the 
elevator foot in position.
3. Rotate the tilt adjust wheel to fine-tune the display angle.  NOTE:The projector is equipped with an “elevator foot” for 
adjusting the projector height.
NOTE:When placing the projector in its carrying case, please 
first retract the elevator foot and tilt adjust wheel to avoid 
breakage.
Elevator Foot
Elevator Button
Tilt Adjust Wheel 
						

							Xerox DP1011 User’s Guide11
Installation
Adjusting the Projector Zoom/Focus
You adjust the focus and zoom in/out with the focus ring and zoom 
ring on the lens housing. To focus the image, rotate the focus ring 
until the image is clear. The projector can focus at distances from 
3.94 feet to 32.81 feet (1.2m to 10.0m). 
Adjusting Projection Image Size
Use the following figure and table to select the best screen 
distance and image size. The table is for reference only.
Focus Ring
Zoom Ring
267.2” (678.7 cm)
213.8” (543.0 cm)
160.3” (407.2 cm)
133.6” (339.3 cm)
80.2” (203.6 cm)
32.1” (81.4 cm) 183.8”
(466.9 cm)
137.9” 
(350.2 cm)
114.9” 
(291.8 cm)
68.9” 
(175.1 cm)
27.6” 
(70.0 cm) 229.8”
(583.7 cm)
3.94’ (1.2m)
9.84’ (3.0m)
16.40’ (5.0m)
19.69’ (6.0m)
26.25’ (8.0m)
32.81’ (10.0m)
Screen 
(Diagonal)Max.32.1” (81.4 cm)80.2” (203.6 cm)133.6” (339.3 cm)160.3” (407.2 cm)213.8” (543.0 cm)267.2” (678.7 cm)
Min. 27.6” (70.0 cm) 68.9” (175.1 cm) 114.9” (291.8 cm) 137.9” (350.2 cm) 183.8” (466.9 cm) 229.8” (583.7 cm)
Screen 
SizeMax. 
(WxH)
25.68” x 19.26”
(65. 1cm x 
48.8cm)64.16” x 48.12”
(162.9cm x 
122.2cm)106.88” x 80.16”
(271.4cm x 
203.6cm)128.24” x 96.18”
(325.8cm x 
244.3cm)171.04” x 128.28”
(434.4cm x 
325.8cm)213.76” x 160.32”
(543.0cm x 
407.2cm)
Min. 
(WxH)22.08 x 16.56”
(56.0cm x 
42.0cm)55.12” x 41.34”
(140.1cm x 
105.1cm)91.92” x 68.94”
(233.4cm x 
175.1cm)110.32” x 82.74”
(280.2cm x 
210.1cm)147.04” x 110.28”
(373.5cm x 
280.1cm)183.84 x 137.88”
(467.0cm x 
350.2cm)
Distance
3.94’ (1.2m)9.84’ (3.0m)16.40’ (5.0m)19.69’ (6.0m)26.25’ (8.0m)32.81’ (10.0m) 
						

							Xerox DP1011 User’s Guide12
User Controls
User Controls
Panel Control and Remote Control
The buttons on the Panel Control and the Remote Control are for 
controlling the projector’s functions.
Panel Control
Power/Standby Indicator—Flashes green during power startup; 
remains steady green when projector is ready.
Warning Indicator—Turns red when projector is overheated, 
flashes red when the projector has a lamp problem or internal 
problem, flashes orange when high-speed cooling is in progress.
Power—Turns projector power on and off. See “Powering On/Off 
the Projector” on page 8 for the specific power on/off sequences.
Source—Selects type of video source: RGB, Component-p, 
Component-i, S-Video, Composite Video, or HDTV.
Enter—When menus are displayed, confirms your selection of 
items on the menus.
Directional Select Keys (       )—When menus are displayed, 
selects items or adjusts settings of items.
Keystone—Adjusts image distortion caused by tilting the projector 
(+/- 16 degrees).
Menu—Opens the On-Screen Display (OSD) menus. To close the 
OSD, press the Menu button again.
Power/Standby 
IndicatorWarning 
Indicator
Directional Select Keys 
						

							Xerox DP1011 User’s Guide13
User Controls
Remote Control
Transmit Indicator Light—Indicates the infrared signal that is 
transmitted to, and received by the projector. 
PiP—Displays the Pip menu of the On-Screen Display (OSD).
Source—Selects type of video source: RGB, Component-p, 
Component-i, S-Video, Composite Video, or HDTV.
Power—Turns projector power on and off. See “Powering On/Off 
the Projector” on page 8 for the specific power on/off sequences.
Hide—Hides image being displayed. Press again to resume 
display of image.
Keystone—Adjusts image distortion caused by tilting the projector 
(+/- 16 degrees).
Freeze—Holds the current image still on the screen. Press again 
to resume the action.
Zoom In/Zoom Out—Enlarges or reduces image. Press Zoom In 
to enlarge the image, press Zoom Out to reduce the image.
Directional Selection Keys (         )—Selects items on the 
OSD menus. If an item is selected, makes adjustments to that 
selected item
Menu—Opens the On-screen Display (OSD) menus. Press the 
Menu button again to exit the OSD.
Transmit Indicator Light 
						

							Xerox DP1011 User’s Guide14
User Controls
On-Screen Display (OSD) Menus 
The On-Screen Display (OSD) menus provide the options to make 
image adjustments and change a variety of settings. The projector 
automatically detects the video source so your selections from the 
menus will apply to that source.
Displaying Menus and Selecting Items
1. To open the OSD Main Menu, press the Menu button on the 
Remote Control or Panel Control.
2. To select one of the menus on the Main Menu, press the 
  keys.
The example above shows the Language menu is selected.
3. Press the Enter button on the Remote Control or Panel Control 
to open the selected menu.
This example shows the All Images menu.
4. When the menu you want is displayed, press the
   keys to select items.
5. To adjust options, press the     keys.
6. To accept your new settings, press the Menu button.
The Main Menu reappears.
7. To exit the OSD, press the Menu button again.
The OSD closes and your new settings are in effect.
Press the           
keys to select 
items from the listPress the   
keys to adjust the 
setting of the 
selected item 
						

							Xerox DP1011 User’s Guide15
User Controls
Choose a Language
1. Press the Menu button on the Remote Control or Panel Control 
to open the OSD.
2. Select the Language menu and press the Enter button.
The Language menu appears.
3. Use the     keys to select the language you want.
The Panel Control only has a   key. Use it to select from the 
menu.
4. Press the Menu button again.
The menus will be displayed in the selected language.