Xerox Projector Dp 1011 User Manual

Xerox DP1011 User’s Guide6
Precautions
Connection Ports
Power Connector—Plug the power cord into the projector here. 
VGA Connector—Use the VGA cable that you received with your 
projector to plug in a computer, HDTV, or component video source.
Composite Video Input Connector—Plug in your composite 
video source here, such as a DVD player or VCR. Requires a 
standard A/V connecting cable. Connect the yellow (video) plug to 
your video source and to the projector.
S-Video Input Connector—Plug in your...

Xerox DP1011 User’s Guide7
Installation
Installation
Connecting the Projector
1. Make sure the projector and computer are turned off.
2. Connect one end of the VGA cable to the projector. Connect 
the other end to the VGA port on the computer.
3. Connect the projector to the other video source(s) with the 
appropriate cable(s).
4. Plug the power cord into the back of the projector and then into 
an electrical outlet.
5. Turn on the projector first, and then the computer.
Video Output
S-Video Output
VGA...

Xerox DP1011 User’s Guide8
Installation
Powering On/Off the Projector
To turn on the projector power
1. Remove the lens cap.
2. Make sure that the power cord and the cables from the video 
sources are securely connected to the projector.
3. Turn on the lamp by pressing the Power button on the control 
panel or on the Remote Control.
The startup screen displays for 20 seconds and the 
Power/Standby indicator flashes green.
When the startup screen disappears, the Power/Standby 
indicator turns a steady...

Xerox DP1011 User’s Guide9
Installation
To turn off the projector power
1. Press the Power button on the projector or Remote Control to 
turn off the projector lamp.
An on-screen message appears: Power off the lamp?
2. Press the Power button again to confirm.
If you don’t press the button again within five seconds, the 
message disappears and the lamp remains lit. This convenient 
design is in case you accidently press the Power button in the 
middle of a show and do not want to turn off the projector....

Xerox DP1011 User’s Guide10
Installation
Adjusting the Projected Image
To raise the projector
1. Lift the projector up and press the elevator button.
The elevator foot pops out.
2. Press the elevator button and hold it in while raising the 
projector to the display angle you want, then release the 
elevator button to lock the elevator foot in position.
3. Rotate the tilt adjust wheel to fine-tune the display angle. The 
tilt adjust wheel is only on the back foot diagonally opposite the 
lens.
To lower...

Xerox DP1011 User’s Guide11
Installation
Adjusting the Projector Zoom/Focus
You adjust the focus and zoom in/out with the focus ring and zoom 
ring on the lens housing. To focus the image, rotate the focus ring 
until the image is clear. The projector can focus at distances from 
3.94 feet to 32.81 feet (1.2m to 10.0m). 
Adjusting Projection Image Size
Use the following figure and table to select the best screen 
distance and image size. The table is for reference only.
Focus Ring
Zoom Ring
267.2” (678.7...

Xerox DP1011 User’s Guide12
User Controls
User Controls
Panel Control and Remote Control
The buttons on the Panel Control and the Remote Control are for 
controlling the projector’s functions.
Panel Control
Power/Standby Indicator—Flashes green during power startup; 
remains steady green when projector is ready.
Warning Indicator—Turns red when projector is overheated, 
flashes red when the projector has a lamp problem or internal 
problem, flashes orange when high-speed cooling is in progress....

Xerox DP1011 User’s Guide13
User Controls
Remote Control
Transmit Indicator Light—Indicates the infrared signal that is 
transmitted to, and received by the projector. 
PiP—Displays the Pip menu of the On-Screen Display (OSD).
Source—Selects type of video source: RGB, Component-p, 
Component-i, S-Video, Composite Video, or HDTV.
Power—Turns projector power on and off. See “Powering On/Off 
the Projector” on page 8 for the specific power on/off sequences.
Hide—Hides image being displayed. Press again to...

Xerox DP1011 User’s Guide14
User Controls
On-Screen Display (OSD) Menus 
The On-Screen Display (OSD) menus provide the options to make 
image adjustments and change a variety of settings. The projector 
automatically detects the video source so your selections from the 
menus will apply to that source.
Displaying Menus and Selecting Items
1. To open the OSD Main Menu, press the Menu button on the 
Remote Control or Panel Control.
2. To select one of the menus on the Main Menu, press the 
  keys.
The...

Xerox DP1011 User’s Guide15
User Controls
Choose a Language
1. Press the Menu button on the Remote Control or Panel Control 
to open the OSD.
2. Select the Language menu and press the Enter button.
The Language menu appears.
3. Use the     keys to select the language you want.
The Panel Control only has a   key. Use it to select from the 
menu.
4. Press the Menu button again.
The menus will be displayed in the selected language.