Xerox Phaser 6300N User Manual

Printing on Specialty Media
Phaser® 6300/6350 Color Laser Printer
3-34 6.Insert the tray into the tray slot, and push the tray completely into the printer.
7.On the control panel, select the paper type:
a.Select Change setup, and then press the OK button.
b.Select Labels, and then press the OK button. 
8.In the printer driver, select either Labels as the paper type or the appropriate tray as the 
paper source.
Printing Glossy Paper
Glossy paper can be printed from any tray. It can be printed on both...

Printing on Specialty Media
Phaser® 6300/6350 Color Laser Printer
3-35
Printing Glossy Paper from Tray 1 (MPT)
1.Open Tray 1 (MPT) by pulling out on the handle. 
2.Pull out the tray extension, and open the paper guides.
3.Fan the glossy paper to release sheets that are stuck together.
 
6300-006
6300-007
Downloaded From ManualsPrinter.com Manuals 

Printing on Specialty Media
Phaser® 6300/6350 Color Laser Printer
3-36 4.Insert the glossy paper into Tray 1 (MPT), and adjust the paper guides to fit the paper.
■Place the side to be printed facedown.
■Do not load more than 25 sheets.
5.On the control panel, select the glossy paper type and size:
a.Select Change setup, and then press the OK button.
b.Select Glossy Paper, and then press the OK button. 
c.Select the paper size, and then press the OK button.
6.In the printer driver, select either Glossy...

Printing on Specialty Media
Phaser® 6300/6350 Color Laser Printer
3-37 2.If necessary, open the paper guides:
■Squeeze the green tab on the length guide, and then slide it back. The guide clicks into 
place.
■Slide the green side guides outward.
3.Fan the paper to release sheets that are stuck together.
6300-001
Downloaded From ManualsPrinter.com Manuals 

Printing on Specialty Media
Phaser® 6300/6350 Color Laser Printer
3-38 4.Insert the paper into the tray. 
Note:Do not load the paper above the fill line indicated on the tray. Overloading the tray 
may cause jams. In the following illustration, 2 indicates the maximum fill line for 
transparencies, labels, glossy paper, and thin card stock.
5.If necessary, press the paper guides inward to fit the paper.
6.Insert the tray into the tray slot, and push the tray completely into the printer.
6300-003
MAX
MAX...

Printing on Specialty Media
Phaser® 6300/6350 Color Laser Printer
3-39 7.On the control panel, select the glossy paper type:
a.Select Change setup, and then press the OK button.
b.Select Glossy Paper, and then press the OK button. 
8.In the printer driver, select either Glossy Paper as the paper type or the appropriate tray as 
the paper source.
Printing Custom Size Paper
In addition to the wide variety of standard paper sizes that you can use for printing, you can 
also print on custom size paper within...

Printing on Specialty Media
Phaser® 6300/6350 Color Laser Printer
3-40 2.Pull out the tray extension, and open the paper guides.
3.Insert the paper into Tray 1 (MPT), and adjust the paper guides to fit the paper. 
■The paper can be loaded with either the long or short edge entering first, as shown in 
the illustrations. 
■The maximum width (X) is 212.5 mm (8.5 in.).
■For single-sided printing, if you are using preprinted or prepunched paper, place the 
side to be printed facedown with the top of the...

Printing on Specialty Media
Phaser® 6300/6350 Color Laser Printer
3-41 7.If you selected New Custom Size, select the custom width and height:
a.For Custom Width, use the Up Arrow and Down Arrow buttons to select the distance 
between the Tray 1 (MPT) guides, and then press the OK button.
b.For Custom Height, use the Up Arrow and Down Arrow buttons to select the height 
of the paper, and then press the OK button.
Note:When you define a new custom size, it is stored in the printer so it can be used 
again....

Phaser® 6300/6350 Color Laser Printer
4-1 This chapter includes:
■Controlling the Quality of Your Prints on page 4-2
■Solving Print-Quality Problems on page 4-5
Print Quality
Downloaded From ManualsPrinter.com Manuals 

Controlling the Quality of Your Prints
Phaser® 6300/6350 Color Laser Printer
4-2
Controlling the Quality of Your Prints
This section includes:
■Selecting a Print-Quality Mode on page 4-2
■Adjusting Color on page 4-3
The print-quality mode and TekColor
 correction directly control the quality of your prints. The 
print-quality mode and paper type directly control the print speed. You can change these 
settings in the printer driver or on the control panel.
Note:Driver settings override the control panel...