Xerox Phaser 4510DX User Manual

Solving Print-Quality Problems
Phaser® 4510 Laser Printer
4-10
Vertical Dark Streaks
There are black lines that appear vertically on the page.
Possible Causes Solutions
The paper path may be contaminated with toner. Print several blank sheets of paper to remove the 
toner accumulations.
The print cartridge may be defective or at the end 
of its life.Replace the print cartridge.
The fuser may be defective. Replace the fuser (in the maintenance kit).
Downloaded From ManualsPrinter.com Manuals 

Solving Print-Quality Problems
Phaser® 4510 Laser Printer
4-11
Dark Spots or Marks
There are dark spots or marks that appear in a random pattern on the page. 
Possible Causes Solutions
The paper path may be contaminated with toner. Print several blank sheets of paper to remove the 
toner accumulations.
The print cartridge may be defective. Replace the print cartridge.
The fuser may be defective. Replace the fuser (in the maintenance kit).
The transfer roller may be defective. Replace the transfer roller...

Solving Print-Quality Problems
Phaser® 4510 Laser Printer
4-12
Unfused or Partially Fused Image
The printed image is not fully fused to the paper and easily rubs off. 
Possible Causes Solutions
The paper may be damp. Replace the paper.
Heavy or unusual paper may be in the tray. Replace the paper with an approved paper type 
then do the following:
■At the printer’s control panel, select Printer 
Setup
, then Paper Handling Setup, and 
then select 
Fuser Configuration. 
■Adjust the fuser setting for the...

Solving Print-Quality Problems
Phaser® 4510 Laser Printer
4-13
Wrinkled Prints
The pages are wrinkled, creased, or torn. 
Possible Causes Solutions
The paper is not loaded correctly in the 
appropriate tray.Verify that the paper is correctly loaded in the 
appropriate tray.
The paper may be in poor condition. Replace the paper.
The paper may be damp. Replace the paper.
The fuser may be at the end of its life. Replace the fuser (contained in the maintenance 
kit).
Downloaded From ManualsPrinter.com Manuals 

Solving Print-Quality Problems
Phaser® 4510 Laser Printer
4-14
Blurred Prints
The image is blurred at the edges. 
Random or Spot Deletions
Areas of the print are extremely light or missing. 
Possible Causes Solutions
The paper may be in poor condition. Replace the paper.
The paper may be damp. Replace the paper.
The print cartridge may be defective. Replace the print cartridge.
Possible Causes Solutions
The paper may be in poor condition. Replace the paper.
The paper may be damp. Replace the paper.
The...

Solving Print-Quality Problems
Phaser® 4510 Laser Printer
4-15
Repeating Defects
Marks or voids are regularly repeated on the page. Use the following table to determine the 
supply that needs replacing.
Different supplies may create print defects with similar measurements. To identify the faulty 
supply:
1.Replace the print cartridge (do not discard the packaging).
2.If the problem continues:
a.Remove and repackage the new print cartridge.
b.Reinstall the original print cartridge.
c.Replace the...

Solving Print-Quality Problems
Phaser® 4510 Laser Printer
4-16
Setting the Fuser Temperature
If the printed image is not fully fused to the paper and easily rubs off, adjusting the fuser 
temperature may produce better results.
The printer has six fuser temperatures that can be configured for each media type. Heavier and 
high cotton content media usually requires a higher temperature to sufficiently bond the toner 
to the paper. Some label media and other heat-sensitive media require low temperature to...

Solving Print-Quality Problems
Phaser® 4510 Laser Printer
4-17
Print Area Is Not Centered on the Paper
The printed area appears outside the margins on the page. Use the following procedure to reset 
the margins.
1.On the control panel, select 
Paper Tray Setup, and then press the OKbutton.
2.Select the tray you are using, and then press the OKbutton.
3.Verify that the tray is set to the correct paper size.
4.If the problem continues, use the Calibrate Margins page to shift the print area on the 
paper....

Phaser® 4510 Laser Printer
5-1 This chapter includes:
■Cleaning the Printer on page 5-2
■Ordering Supplies on page 5-5
■Extended Periods of Non-Use on page 5-7
■Moving and Repacking the Printer on page 5-8
Maintenance
Downloaded From ManualsPrinter.com Manuals 

Cleaning the Printer
Phaser® 4510 Laser Printer
5-2
Cleaning the Printer
For safety information, see User Safety on page A-1.
Cleaning the Outside of the Printer
To remove stains, clean the outside of the printer using a soft, damp cloth moistened with a 
mild neutral detergent. Do not spray detergent directly onto the printer.
Warning:To prevent electric shock, turn the printer off and unplug the power cord from the 
electrical outlet before cleaning the printer.
Use only an approved toner vacuum to...