Xerox 1632 2240 3535 Color Carrera Manual

6/02
6-67 DC1632/2240
dC132, dC135
General Procedures and Information Prelaunch Training/Review
dC132 Serial Number/Billing Meter SynchronizationPurposeChecks the Billing Meters and sets the Machine Serial Number when fault 103-208 occurs.
This routine also reads the Billing Meters and can be accessed at any time for this purpose.Procedure
CAUTION
Failure to comply with the board replacement procedure in GP 10 Replacing Billing PWBs,
could result in catastrophic NVM corruption.
Follow the procedure...

6/02
6-68DC1632/2240
dC140, dC188
Prelaunch Training/Review General Procedures and Information
dC140 Analog MonitorPurposeMonitors the analog values of the A/D converter sensors by driving each component (e.g.;,
C.C). Temporary change of output values is possible. Output component check is also possi-
ble.Procedure1. Enter the Diagnostic Mode. Refer to Entering Diagnostic Mode using the PWS.
2. Select the Analog Monitor (dC140) tab in the Diagnostics Screen.
3. The system displays the Analog Monitor...

6/02
6-69 DC1632/2240
dC301
General Procedures and Information Prelaunch Training/Review
dC301 NVM InitializationPurposeThis procedure may be needed when the machine cannot recover for some unknown reasons,
including problems such as producing blank copies/prints, Xerographic CRUs not recognized,
continuously giving system fault, etc.Initial Actions to be taken:Obtain all of the following information:
ï Disconnect any Foreign Interface Devices prior to performing this procedure.
ï NVM Value Factory...

6/02
6-70DC1632/2240
dC305, dC330
Prelaunch Training/Review General Procedures and Information
dC305 UI Component CheckPurposeChecks the operations of the UI Screen and Control Panel buttons.Procedure1. Enter the Diagnostic Mode. Refer to Entering Diagnostic Mode using the PWS.
2. Select the Diagnostics Tab in the Service Entry Screen.
3. Select the System Test Tab in the Diagnostics Screen. The System Test Screen displays.
The UI Component Check dC305 is the default screen.
4. Select Start. The...

6/02
6-71 DC1632/2240
dC330
General Procedures and Information Prelaunch Training/Review001-306 INTLK_3 High when Open is detected. ON: High
004-100 Belt Home Sensor [Operation Description]: IBT is not at Home Posi-
tion. Open circuit. It is necessary to operate IBT 
5V ON. ON: High
004-101 Drum Motor YMC Fail Detec-
tionPR (Drum) Motor YMC Failure ON: High
004-102 Drum Motor K Fail Detection PR (Drum) Motor K Failure ON: High
004-200 FAN_LOCK_FAIL Fan rotation is stopped ON: FAIL
005-102 Document Sensor...

6/02
6-72DC1632/2240
dC330
Prelaunch Training/Review General Procedures and Information009-153 #C_CRU detect CRU is installed
009-154 #K_CRU detect CRU is installed
009-200 2nd BTR Retract Sensor RetractiON. ON: Low
009-201 POB Sensor Paper detected ON: Low
009-203 1st BTR Retract Sensor RetractiON. ON: Low
010-101 Fuser Exit Paper detected ON: High
010-102 Full Paper Stack Sensor NotFull ON: Low
010-103 Face Up Exit Sensor Paper detected ON: High
012-100 IOT Regi Clutch Clutch OFF ON: High
012-101...

6/02
6-73 DC1632/2240
dC330
General Procedures and Information Prelaunch Training/Review005-081 Exit Motor Non 
CVT ModeOperate the DADF Exit Motor  -
005-083 Doc Ready switch ON the Doc Ready signal.  -
005-084 Doc Set LED switch ON the DOC SET LED  -
006-002 IIT Exposure Lamp switch the Lamp ON for 180sec -> Auto 
OFF -
006-004 IPS Cooling Fan 
(Low speed)After operating the IPS Cooling Fan at high 
speed for 5sec, operate it at low speed. 
ON: FAN ON: 24V, FAN Slow: L->H (About 
13V) -
006-005 IIT...

6/02
6-74DC1632/2240
dC330
Prelaunch Training/Review General Procedures and Information008-030 TTM TA Motor 
(104mm/sec)Start operation. Turns OFF automatically at 
1000msec. 8-029, 031, 
032, 033, 034, 
035, 036
008-031 TTM TA Motor 
(192mm/sec)Start operation. Turns OFF automatically at 
1000msec. 8-029, 030, 
032, 033, 034, 
035, 036
008-032 TTM TA Motor 
(370mm/sec)Start operation. Turns OFF automatically at 
1000msec. 8-029, 030, 
031, 033, 034, 
035, 036
008-033 TTM TA Motor 
(52mm/sec)...

6/02
6-75 DC1632/2240
dC330
General Procedures and Information Prelaunch Training/Review009-026 #Y_BCR DC High voltage output value of BCR DC_Y.  
ON: PWM 9-30
009-027 #M_BCR DC High voltage output value of BCR DC_M.  
ON: PWM 9-31
009-028 #C_BCR DC High voltage output value of BCR DC_C.  
ON: PWM 9-32
009-029 #K_BCR DC High voltage output value of BCR DC_K.  
ON: PWM 9-33
009-030 #Y_BCR AC High voltage output value of BCR AC_Y. 
ON: PWM 9-26
009-031 #M_BCR AC High voltage output value of BCR AC_M  9-27...

6/02
6-76DC1632/2240
dC330
Prelaunch Training/Review General Procedures and Information012-032 Eject Clamp Low 
DownTurns OFF automatically at 702pulses after 
the Eject Home Snr detected Home Posi-
tion. 12-30, 12-31, 
12-33, 12-34, 
12-41
012-033 Eject Clamp Mid-
dle DownTurns OFF automatically at 365pulses after 
the Eject Home Snr detected Home Posi-
tion. 12-30, 12-31, 
12-32, 12-34, 
12-41
012-034 Eject Clamp UP Turns OFF automatically at 46pulses after 
the Eject Home Snr detected Home Posi-
tion....