Whirlpool Wp 88 Installation And Maintenance Instructions

							Whirlpool is a registered trademark of Whirlpool USA5019 396 01167
1
GBWP 88
Before using the dishwasher, read the 
installation and maintenance instructions carefully!
1) Programme data obtained in conformity with European standard EN 50242. The data may vary, for example, according to   
different loads, extra functions, sensor settings (only with sensor programmes), water supply temperatures, water hardness 
and power supply voltage.
2) Programme for energy data label in conformity with EN 50242. - Information for Test Laboratories:
 for more detailed information 
on the conditions of the EN comparison test and other tests, contact the following address: “[email protected]”.
1. OVERVIEW
On button
Off button
Fault indication and wash time displayWith “Delayed start” selected, it indicates the time 
remaining until the start of the programme (hh). Toward 
the end of the programme, during the drying cycle, the 
display will indicate the time remaining in minutes.
If “F..” – appears on the display, see chapter 5 “What to do if…”.
D
elayed start buttonThe wash cycle can be programmed to start after 1- 24 
hours. (With each successive touch of the button, the 
delayed start indicator increases by 1 hour, and after 24 
returns to 00).
Then press the START button. The wash programme 
will start after the set time.
Detergent setting upon initial use and when using a different type of 
detergent1. Press and hold down the program selector, then press the Delayed Start 
button. The last detergent type selected will be shown on the display. 
2. With the Delayed Start button, set the required detergent 
(“--” = powder, “2 l” = 2 in 1, “3 l” = 3 in 1, “A l” = all the other 
combined detergents) (in this way the rinse aid and salt level 
indicator lamps are deactivated). The type of detergent selected 
will be shown on the display.
3. Wait 5 seconds or switch off the appliance, the selected detergent 
type is memorised. It is shown on the display for about 3 seconds 
after switching on. Note that only after changing the detergent type 
it is possible to select the desired programme and, if necessary, 
select the delayed start button.
Programme selectorPress the button (repeatedly) until the indicator of the 
required programme lights up.
START button
The indicator lights up during operation, flashes if a fault 
occurs and goes off at the end of the programme.
START
 button RESET function:Press this button for at least 2 seconds and the started 
programme and the extra functions selected are cancelled. 
The main fault indications (repeated flashing of the START 
indicator) can be cancelled with a RESET. Detailed 
instructions are given in chapter 5 “What to do if...”.
Rinse aid level indicator and salt level indicator
These indicator lamps light up when rinse aid or salt 
need to be added. 
Only add just before starting a wash cycle.
Table 1.1.
Programme TableDetergent 
dispenserConsumption1)
PProgrammesAvailable 
optionsDescription of 
programmelargesmallLitreskWhMinutes
1Sensor Intensive60-70°CRecommended programme 
for heavily soiled crockery, 
with dried-on food, e.g. pots 
and pans.XX13-201.10-2.00100-150 ±1)
2Sensor Normal40-55°CAutomatic program for 
routine washes, for crockery 
with no dried- on food (not for 
EN 50242).XX10-130.80-1.0560-120 ±1)
3Eco2)50°CNormally soiled crockery.XX12.01.05170 ±1)
4Half Load50°CIdeal for washing a half load of 
lightly or normally soiled 
crockery.XX10.01.04145 ±1)
5Power Clean70°C
Recommended programme 
for heavily soiled crockery, 
particularly suitable for pots 
and pans. Intensive wash with 
additional water jets.
XX16.01.80220 ±1)
 
						

							2
2. QUICK REFERENCE GUIDE
Detailed instructions are given in the following pages, see also chapter “5. What to do if...”
1. Switch on the 
applianceOpen the dishwasher door.
Press the 
ON button.
2. Select a programmePress the button   or   to bring up the desired programme on the display. 
Select options, if available.
3. Select the type of 
detergentThe detergent selection procedure varies depending on the dishwasher model. 
Chapter “1. Overview ” provides instructions for selecting detergent type.
4. Fill in the detergent4a. Powder/gel/tabsFill the detergent dispenser compartments in 
accordance with the wash programme selected.
Large compartment 
A for every wash cycle, additional 
small compartment 
B for programmes with pre-wash 
(see table 1.1.).
4b. Combined action detergents (2 in 1/3 in 1/... etc.)
Place the detergent in compartment 
A, as per the 
manufacturers recommendations.
5. Check the rinse aid 
level
6. Check the salt levelDepending on the model:
7. Load the racks
Make sure that the spray arms can turn freely and are not impeded by crockery 
or cutlery in the racks.
Detailed instructions on loading the racks are given in chapter “3. How to use 
the appliance”, under “How to load the racks”.
8. Start the appliancePress the START button.
9. Turn on the water 
tap and close the 
dishwasher doorWhen the door is closed the dishwasher 
starts automatically.
Wash cycle
If the appliance is switched off during a 
wash cycle, when switched on again it will 
resume the cycle from where it was 
interrupted. Care must be taken when 
opening the door, as steam will escape!
10.End of programmeAt the end of the programme an acoustic signal will sound. 
The START indicator lamp switches off.
11.Open the door, 
switch off the 
appliancePress the
 OFF button. All the indicator lamps switch off.
12. Turn off the water
tap, unload the racksUnload the appliance, starting from the lower rack in order to avoid any 
residual drips of water falling onto crockery below.
ACB
Visual indicator in dispenser 
C
dark 
➯sufficient rinse aid present,
clear 
➯add rinse aid (approx. 150 ml).
The indicator lamp on the control panel lights up when rinse aid 
needs to be added. Not all models are equipped with such an 
indicator.
window in salt reservoir cap on bottom of appliance inside
orange
➯when sufficient salt is present,
clear
➯when salt needs to be added.
The indicator lamp on the control panel lights up when salt needs 
to be added. Even once salt has been added, the indicator lamp 
only switches off after several wash cycles!
Change the programme in progress:-  Press the START button for 
about 2 sec., until the START 
indicator lamp switches off.
- Close the door.
-  (Water drains for up to 60 seconds).
- Open the door.
-  Select a new programme.
-  Press the START button.
 
						

							3
3. HOW TO USE THE APPLIANCE
PROGRAMME SELECTION
Press the button   or   to bring up the desired programme on the display. The appliance must be switched 
on. If required, select options (if supplied). The corresponding indicator lamp switches on. Appropriate 
programmes and relative available options are detailed in table 1.1 on page 1.
Programme times stated in the table were obtained under normal conditions and may vary 
depending on conditions. Differences of up to 20 minutes are possible with sensor programmes 
as a result of the appliances automatic calibration system.
HOW TO FILL THE DETERGENT DISPENSER
Only fill the detergent dispenser prior to starting a wash programme. 
Only use detergents 
specially recommended for dishwashers, observing the manufacturers recommended dosage. 
Observe the manufacturers safety warnings!
Open the detergent dispenser compartments by pushing the left button (button 
1) of the dispenser.
a. Powder/gel/tabs
Fill the detergent dispenser compartments in accordance with the wash programme selected (table 1.1).
Programmes without pre-wash:
pour the entire recommended dosage into compartment 
A.
Programmes with pre-wash:
pour 2/3 of the recommended dosage into the large compartment 
A and 1/3 into the small compartment 
B.
Dishwasher tabs should be placed, according to the 
manufacturers recommendations, in compartment 
A.
If the “Half load” option is selected, detergent dosage should be 
reduced by approximately 1/3.
b. Combined action detergents (2 in 1/3 in 1/... etc.)
Combined action detergents should be placed, according to the 
manufacturers recommendations, in compartment 
A.
Firmly close and press the detergent compartment lid shut after filling.
Detergents with rinse aid incorporated may be effective only with longer programmes. In the 
case of shorter programmes, detergent residue may be a problem (if necessary, use powder 
detergent). Detergents with rinse aid incorporated tend to form excess suds.
The guarantee is not applicable if faults are caused by the use of these products.
HOW TO CHECK/FILL/ADJUST RINSE AID
Not necessary when using a combined action detergent.
a. How to check the rinse aid level 
Check the visual indicator 
C on the rinse aid dispenser: dark = sufficient rinse aid, clear = add rinse aid.
In the case of appliances with an electric indicator on the 
control panel, the rinse aid indicator lamp   lights up red 
when rinse aid needs to be added.
b. How to fill the rinse aid dispenser
Open the rinse aid dispenser by pressing the right button 
(button 
2) of the dispenser.
Fill the dispenser with rinse aid up to the “max” line 
(approx. 150 ml).
Shut the lid again.
Only use rinse aids recommended for use in domestic dishwashers. 
Immediately wipe away 
any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault 
function of the appliance.
button 
1 Large
compartment 
ASmall
compartment
 B
button 
2 Indicator 
C
max
 
						

							4
3. HOW TO USE THE APPLIANCE
c. How to adjust the rinse aid dosage regulator
The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less 
rinse aid is dispensed (factory setting: position 4).
Press the button 
2 to open the cover.
Using a coin or similar object, turn the arrow to the desired setting. 
After adjusting the rinse aid setting, shut the cover again.
If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is 
not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes 
have more difficulty drying and a higher rinse aid setting will not improve the situation.
HOW TO CHECK/FILL/ADJUST SALT
Only use regeneration salt specifically for dishwashers.
a. How to check the salt level
Depending on the model, check the visual indicator  . The window on the salt reservoir cap is clear when salt 
needs to be added and orange when the salt present is sufficient. In the case of appliances with an electric indicator on 
the control panel, the salt indicator lamp   lights up red when salt needs to be added.
b. How to fill the salt container
- Remove the lower rack.
- Turn the salt container cap anti-clockwise to open it.
- When using the dishwasher for the first time, fill the salt container to the rim with water.
- Using the funnel provided, fill with regeneration salt to the rim (the first time, 
min. 1.5 kg/max. 2 kg).
- Stir with the handle of a wooden spoon to help dissolve the salt. 
- Close the cap of the salt container by turning it clockwise. 
- Reinsert the lower rack.
Once regeneration salt is added, 
immediately start a wash programme (the “Pre-wash” 
programme alone is 
not sufficient). Residual saline solution or grains of salt can lead to deep-
down corrosion, irreparably damaging the stainless steel components. The guarantee is not 
applicable if faults are caused by such circumstances.
The salt level indicator lamp may remain lit for the duration of several wash cycles.
If the water hardness level falls within category 1 (soft),
 no salt is required.
c. How to set the water hardness level
- Switch on the appliance.
- Select the 2nd programme “P2” - consult the table 1.1 in chapter 1.
- Press the START button for at least 5 seconds until the START indicator lamp flashes.
- The set water hardness level is shown on the display (if present) or the START button flashes.
- With each successive touch of the START button the setting increases and when it reaches 7 it returns to 1 again.
- The appliance must be switched off to memorise the new setting.
Water hardness level is factory set at 3 for medium-hard water (display 4 or 4 flashes of the 
START button).
Water hardness level 4 with combined action detergent
Even if you use a combined action detergent which includes salt, you must still add regeneration 
salt since such detergents are not effective enough at softening hard water.
If the appliance is equipped with the function “Select detergent” (see chapter “1. Overview ”), 
set the detergent dispenser system to the “no salt” setting so that the salt indicator lamp remains 
activated (“Detergent with rinse aid”).
Water hardness German degrees
°dHFrench degrees 
°fHEnglish degrees 
°eHFlashing frequency
or display setting
1 soft 0 - 5 0 - 9 0 - 6.3 1 / 1x
1 - 2 medium 6 - 10 10 - 18 7 - 12.6 2 / 2x
2 medium 11 - 15 19 - 27 13.3 - 18.9 3 / 3x
3 medium-hard 16 - 21 28 - 37 19.6 - 25.9 4 / 4x
4 hard 22 - 28 38 - 50 26.6 - 35 5 / 5x
4 very hard 29 - 35 51 - 63 35.7 - 44.1 6 / 6x
4 extremely hard 36 - 60 64 - 107 44.8 - 74.9 7 / 7x
 
						

							5
3. HOW TO USE THE APPLIANCE
HOW TO LOAD THE RACKS
CUTLERY RACK:May be used in two different positions.
In position 2 the upper rack must be 
lowered (see “Upper rack height 
adjustment” 
C below).
For optimum washing results, position 
cutlery as shown (handles of spoons 
facing inwards).
Beware of sharp/pointed items. Risk 
of injury!
UPPER RACK 
- depending on model:
The two handles 
C must be level.
Washing without the upper rack/cutlery rack
If the appliance is equipped with the adjustable retainers shown in the figure, the 
upper rack/cutlery rack can be removed in order to accommodate large items. 
Open the two retainers 
D and slide the upper rack/cutlery rack out.
When the upper rack/cutlery rack is in place, the retainers must 
always be closed.
LOWER RACK
 - depending on model:
Arrange crockery so that water does not collect in cavities, ensuring that the spray arms turn freely.
Only use dishwasher-proof crockery and dishes. Do not use the dishwasher for washing wooden items, aluminium, tin, silver 
cutlery or decorated crockery (unglazed).
RINSE
The dishwasher door must be closed and the water tap open.
To load crockery, open the door with caution:
Hot steam!
Close the door again. The programme resumes the cycle from where it was 
interrupted.
The wash cycle can be interrupted at any time by pressing 
RESET.
PROGRAMME END
Exercise caution when opening the door: beware of 
hot steam.
Press the 
OFF button only after the START button indicator has gone off. All the indicator lamps switch off. Unload the appliance, starting from 
the lower rack in order to avoid any residual drips of water falling onto crockery below.
For even better drying results, leave the dishwasher door open a little before unloading in order to allow the steam to 
dissipate, helping the dishes to dry. The underside of the kitchen worktop must be protected (see instructions in “Maintenance 
and Installation”).
Position 2 Position 1
Cutlery holder
AMay be removed individually, depending on upper 
rack load.A
Adjustable glass holder
BDepending on the position, for small or long-
stemmed glasses.
Rack height adjustment
CThe upper rack height can be changed even when loaded,
Lower adjustment: pull out the two side handles 
C 
and lower the rack.
Upper adjustment: pull the two handles 
C up until 
the rack clicks into place 
(standard position).
D
Retainer
closedRetainer
open
BB
D
C
D
F
E
GPlate holders
EPartially folding for maximum 
rack loading flexibility.
Zone
FIntensive wash with 
Power 
Clean.
Cutlery Basket
GWith the “Half load/Multizone” 
option, use the lower rack and 
press the “Half load/Multizone” 
button twice.
Changing the programme in progress/Resetting
- Press the START button for 2 sec. until the START indicator 
lamp switches off.
- (Water drains for up to 60 seconds).
- The appliance is now ready to be restarted.
Built-in models
- Press the START/RESET button (for 2 seconds).
-Close the door.
- (Water drains for up to 60 seconds).
- The appliance is now ready to be restarted.
 
						

							6
4. PRECAUTIONS AND GENERAL RECOMMENDATIONS
1. Packing
The packaging materials are 100% recyclable and marked with the recycling symbol.  .
2. Removing the packaging and inspecting the contents
After unpacking, make sure that the dishwasher is undamaged and that the door closes correctly. If in doubt, contact a 
qualified technician or your local retailer.
3. Before using the dishwasher for the first time
- The appliance is designed to operate at ambient temperatures of between 5°C and 45°C.
- This dishwasher has been tested by the manufacturer to ensure it functions correctly. Such testing may leave slight 
drips/ water marks which will disappear with the first wash.
4. Energy and water savings
- Do not rinse crockery under running water.
- Always fully load the dishwasher before running it or select the “Half load/Multizone” function (if available).
- If ecological energy sources are available such as solar panel heating, heat pumps or centralised heating systems, the 
appliance may be connected to the hot water mains up to a maximum temperature of 60° C. Make sure the water inlet 
hose is of the correct type (“70°C Max” or “90°C Max”).
5. Child safety
- Keep the packaging materials out of the reach of children.
- Children must not be allowed to play with the dishwasher.
- Store the detergent, rinse aid and salt out of the reach of children.
6. Safety warnings
- The appliance is not intended for use by children or physically or mentally impaired persons, unless adequately 
supervised by a responsible adult capable of guaranteeing safe use of the appliance.
- Do not operate the appliance in the open air.
- Do not store flammable materials in close proximity to the dishwasher.
- The water in the dishwasher is not potable.
- Do not use solvents inside the dishwasher: risk of explosion!
- Be careful when the door is open: risk of tripping!
- The open dishwasher door can only support the weight of the loaded rack when pulled out. Do not rest objects on 
the open door or sit or stand on it.
- Sharp items that might cause injury (e.g. knives), must be placed in the cutlery basket with the sharp end facing 
downwards. Long-handled utensils must be arranged horizontally in the upper rack, with the sharp end facing away 
from the front of the appliance.
- Before cleaning or carrying out maintenance, disconnect the mains plug and turn off the water tap; also in the 
event of any malfunction.
- Repairs and technical modifications must be carried out exclusively by a qualified technician.
7. Resistance to frost
If the appliance is placed in surroundings exposed to the risk of frost, it must be drained completely. 
Turn off the water tap, remove the inlet and outlet hoses, and let all the water drain away. Make sure there is at least 
1 kg of dissolved regeneration salt in the salt container, to protect the appliance from temperatures of up to -20°C. 
When the programme resumes, an error message may be displayed. 
“F1”/START indicator flashes once: pour half a litre of warm water into the bottom of the dishwasher.
“F6”/START indicator flashes 6 times: the appliance must remain at an ambient temperature of min. 5°C for at least 24 hours.
After eliminating these faults, RESET the appliance (see chapter “5. What to do if...”).
8. Disposal
- The appliance is manufactured using recyclable materials. If you decide to scrap the dishwasher, it must be 
disposed of in compliance with local waste disposal regulations. Make it unusable by cutting off the power cord. To 
prevent situations of potential danger to children (e.g. danger of suffocation), break the lock of the door so that it 
can no longer be closed.
- This appliance is marked according to the European directive 2002/96/CE on Waste Electrical and Electronic 
Equipment (WEEE). By ensuring that this appliance is scrapped suitably, you can help prevent potentially damaging 
consequences for the environment and health. Unsuitable disposal of an appliance of this type as household waste 
could have detrimental effects on the environment. The symbol   on the appliance, or on documentation enclosed 
with the appliance, indicates that this product must not be treated as household waste, but must be delivered to the 
nearest collection centre for the recycling of electrical and electronic appliances. Disposal must be carried out in 
accordance with local environmental regulations for waste disposal. For further information on the treatment, 
recovery and recycling of this appliance, contact your competent local authority, the collection service for household 
waste or the shop where you purchased the appliance.
EC Declaration of conformity
This appliance has been designed, constructed and distributed in compliance with the safety requirements of EC Directives:
2006/95/CE, 89/336/CE, 93/68/CE and 2002/95/CE (RoHS Directive).
Loading Capacity:
 13 place settings.
 
						

							7
5. WHAT TO DO IF...
If a fault occurs, 
before contacting the After-sales Service, make the following checks to try and remedy the 
problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal 
appliance operation.
The appliance... Possible causes/solutions
...is not working/will not start - The appliance must be switched on.
- Check the household circuit fuse if there is no power supply.
- The dishwasher door must be closed.
- Check whether the “Delayed start” function (if available) has 
been selected. If it has, the appliance will only start once the set 
time has elapsed. If necessary, set the delayed start to “0” 
(RESET the appliance).
... shows “F1” on the display or 
the START indicator lamp flashes once- The water supply temperature must be above 3°C.
... shows “F4” on the display or 
the START indicator lamp flashes 4 times- The filters must not be dirty or clogged.
- The drain hose must not be kinked.
- The closure disk of the syphon hose connection must be 
removed.
... shows “F6” on the display or 
the START indicator lamp flashes 6 times- The water tap must be open.
- The water inlet hose must not be kinked and the relative inlet 
filter in the water tap connector must not be clogged.
... shows “F7” on the display or 
the START indicator lamp flashes 7 times- The water tap must be fully open during water inlet (minimum 
capacity: 0.5 litres per minute).
- The water inlet hose must not be kinked and the relative inlet 
filter in the water tap connector must not be dirty.
... shows “F8” on the display or 
the START indicator lamp flashes 8 times- The filters must not be dirty or clogged.
- Concave items (e.g. bowls, cups) must be arranged facing 
downwards in the rack.
- The drain hose must be fitted correctly (for high built-in 
appliances, leave min. 200-400 mm from the lower edge of the 
appliance - see instructions in “Maintenance and Installation”).
... shows other “F” faults on the display or 
the START indicator lamp flashes Xx times- Reset the appliance (see below).
After taking the above course of action, the fault message must be reset. In the majority of cases the 
fault is thus eliminated.
RESET:
➯Press the START button for approx. 2 seconds until the indicator lamp switches off or 
press the RESET button (depending on model).
➯Close the door.
➯Water drains automatically for up to 60 seconds.
➯The appliance is now ready to be restarted.
Crockery and cutlery ... Possible causes/solutions
...are not perfectly clean/have food 
residues- Arrange crockery so that items do not touch each other.
Concave items (e.g. bowls, cups) must be arranged facing 
downwards in the rack.
- If necessary, use more detergent, observing the manufacturer’s 
indications as regards dosage. Always store detergent in a dry 
place and do not store it for excessively long periods of time.
- For heavily soiled crockery, select a wash programme with a 
higher temperature (see table 1.1 on the first page).
- If you select the “Half load/Multizone” function (if available), 
remember to load 
only the upper rack or 
only the lower rack to 
increase washing power and thus obtain optimum wash results.
 
						

							8
5. WHAT TO DO IF...
Crockery and cutlery ... Possible causes/solutions
...are not perfectly clean/have food 
residues- In the event of frequent use of low temperature programmes 
(50°C or lower) (if available), every now and again select a 
higher temperature programme
- The spray arms must not be clogged, the filters must not be 
dirty and must be fitted correctly (see the instructions in 
“Maintenance and installation”).
- The spray arms must be able to turn freely and must not be 
impeded by crockery or cutlery.
...have deposits:
- regeneration salt residue- In areas with very hard water, more regeneration salt needs to 
be added (see page 4, “How to check/fill/adjust salt”).
- Close the salt container lid properly.
- If you use a combined action detergent which includes salt, do 
not add any additional regeneration salt.
- rust marks - Salty or acidic food residues can cause rust marks even on 
stainless steel cutlery. 
To avoid this, always use the pre-wash programme if the dishes 
are to be washed later.
- other marks- In the presence of marks, increase the rinse aid dosage (see 
page 3, “How to check/fill/adjust rinse aid”).
- If you use a combined action detergent, possibly add more rinse 
aid.
- streaks - In the presence of streaks, reduce the rinse aid dosage (page 3, 
“How to check/fill/adjust rinse aid”). If you use a combined 
action detergent which includes rinse aid, do not add any 
additional rinse aid.
- suds- Only use the amount of detergent/rinse aid required, since 
excessive amounts can lead to excess suds.
- opaque glasses, etc. - Only use dishwasher-proof crockery and dishes.
...have discoloured plastic partsTomato sauce, for example, can lead to discolouring of plastic parts. 
Powder detergent is recommended as it allows slightly higher doses 
to be used for improved whitening. Programmes with higher wash 
temperatures should be used.
...are not dry  - Arrange crockery so that water does not collect in cavities.
- Increase the dosage of rinse aid (see page 3, “How to check/fill/
adjust rinse aid”).
- Dishes dry better if the dishwasher door is left open a little 
before unloading; this allows the steam to dissipate.
- With the Rapid 40°C programme (if available), dishes may not 
be perfectly dry since this is a short programme. If necessary, 
select a longer programme.
If, after carrying out the above checks, the fault persists, disconnect the mains plug and turn off the 
water tap. Contact the After-sales Service (see warranty).
Before contacting our After-Sales Service, take note of the following:
- the description of the fault,
- the appliance type and model,
- the service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side:
We reserve the right to make technical modifications.