Vivitek Dw3351 User Manual

							— 44 — 
Wireless LAN Settings 
1. Connect the Vivitek wireless dongle (optional) to the USB TYPE-A port of the projector. 
2. Select SYSTEM SETUP >> Advanced >> Network Settings >> Wireless LAN menu 
3. In an AP mode connection, you must first obtain the target SSID information. In the pwPresenter 
search for the wireless SSID host. 
For a connection in infrastructure mode, select the projector’s SSID to connect. 
 
4. On the computer, use the wireless network function to connect to a wireless network. 
5. If the wireless network requires a password, the user must manually enter the password. 
Browser Based Management 
1. Open a browser such as the Microsoft Internet Explorer*. 
2. In the Address bar, type the projector’s IP address as set in Wired LAN Terminal Function. The 
projector is setup for web control page. The LAN/RJ45 function displays as follows. 
The Information page displays the information and status of this projector.  
 
* Adobe Flash Player 9.0 or higher is required to view the interface through the browser.  
						

							 
– 45 – 
The General Setup page provides the normal functionality of the OSD, such as: 
power/source/volume/Freeze Auto search/Lamp mode control. 
 
The Display Setup page provides image fine tuning functionality. 
 
The Display Setup page provides keystone and aspect ratio adjustment functionality. 
  
						

							— 46 — 
The Alert and Mail Settings pages provide status and mail notification functionality. 
 
The Network Setup page provides configuration functionality for wired or wireless network setup. 
 
The Advance Setup page provides broadcasting and projector name modification functionality. 
  
						

							 
– 47 – 
The Presenter Setup page provides pwPresenter admin and normal user password setup. 
 
The download page provides downloading a function for pwPresenter. 
 
The Crestron page, supporting RoomView version 6.2.2.9, is only available on a Wired LAN network setup. 
It allows remote control of the projector. 
 
For more information, visit http://www.crestron.com. 
pwPresenter 
The pwPresenter is a computer-based application to allow remote display of the computer’s desktop on 
the projector. pwPresenter works through a properly configured wireless or wired network connection. 
Make sure all other virtual networks control programs are disabled before using pwPresenter.  
						

							— 48 — 
1. Connect an RJ45 cable to the projector and computer’s RJ45 ports. 
2. Enter the IP address of the projector in the address bar of an open browser. 
3. Download pwPresenter (Zipped file) from the web control page. Unzip it and install the 
pwPresenter on the computer.  
4. Once installed, double click the pwPresenter icon. The pw Presenter page appears. 
5. Click the Search icon to search and connect to a networked display. 
 
a. Type in the IP address (see Browser Based Management on page 44 for details.) and 
click Search. 
b. The networked projector is displayed. Select it to continue. 
c. Click Connect and the computer’s desktop image is displayed through the projector. 
  
						

							 
– 49 – 
d. After connecting to the projector, pwPresenter prompts for a password, as set up in the 
Presenter Setup screen. 
 
e. Click the disconnect button to disconnect all available projectors. 
6. Controlling the remote display 
a. Click Play/Pause  to display the desktop on the connected network display. 
b. Display up to four computers on a single projector at one time. Click a location to display 
the image. Four locations can be selected (1-4) or two in a continuous mode (Left and 
right) for two computers.  
c. Once the display is selected the image displays through the projector. Select any location 
or revert to full screen or blank out mode. 
d. Capture mode allows management of advanced functions. 
e. Define the projector’s display area 
i. Full Screen: displays the entire screen through the projector. 
ii. FixedSize: displays a fixed screen, place the screen over a desired area to 
identify the display area for the projector. 
iii. Alterable: displays an adjustable screen, which is used to identify the display area 
for the projector. 
  
						

							— 50 — 
7. Click the Basic Setting tab to configure pwPresenter basic settings. 
 
a. Select the interface language: click the drop-down menu and select the desired language. 
Click Apply. 
b. Change the size of the FixedSize frame in capture mode. Enter the size in pixels units. 
Click Apply to save the settings. 
c. Enable the mirror driver upon startup (driver must be previously installed).  
d. Allow message notification. Click Yes, then Apply to save the settings. 
e. Displays the software information. 
1 
2 
3 
4 
5  
						

							 
– 51 – 
8. Click the Advanced Setting tab to configure pwPresenter advanced settings. 
 
a. Set the image quality setting. Click the drop-down menu to select the desired image 
quality. Click Apply to save the setting. 
b. Define the network port, fixed or manual. If manual is selected, enter the port number. 
Click Apply to save the setting. 
1 
2  
						

							— 52 — 
9. Click the Global Setting tab to configure pwPresenter global settings, which allows for remote 
control of the computer through the projector.  
 
10. Click the Multicast Setting tab to configure pwPresenter broadcast settings. 
  
						

							 
– 53 – 
11. Device management. 
 
a. Click the Display Port Location icon to adjust the location of the displayed area. 
b. Click the Password icon to change the user password. 
c. Click the Disconnect icon to disconnect the projector from the network. 
d. Click the Webpage icon to allow access to the Vivitek webpage control interface. 
e. Click the Remote Desktop icon to enable the remote access function. 
f. Displays the device status and setting information. Also, provides access to conference 
control mode.  
Using the Broadcasting Function 
The 1:N LAN Display is available in two ways. 
 TCP/IP—supporting up to 8 projectors (default) 
 Multicast—supporting up to 255 projectors (new design) 
Select the channel for the corresponding IP address (grayed out): 1 to 25. 
Twenty five channels (25 IPs) are available for selection, for example: 239.192.19.21 ~ 45. 
Pre-set channels, such as a channel setup for emergency broadcasting, are automatically detected by the 
projector and the source is displayed. Manual source selection is not required. 
To activate this function: 
1. Go to the SYSTEM SETUP >> Advanced >> Network Settings menu after opening the OSD menu. 
2. Press ENTER. 
a  b  c  d  e 
f