Vivitek Dw3351 User Manual

							— 24 — 
MAIN MENU  SUB MENU     SETTINGS 
SYSTEM 
SETUP >> 
Advanced 
 High Altitude 
Mode 
    Off, On 
 Audio Settings  Mute   Off, On 
  Volume   0 ~ 10 
  Out   Off, Mini, RCA 
 Lamp Settings  Lamp Mode   Normal, ECO, Dynamic ECO 
  Reset Lamp Timer   Yes, No 
  Total Lamp Hour    
 Test Pattern     Off, Grid, White, Red, Green, 
Blue, Black 
 Closed Caption  Closed Caption 
Enable 
  Off, On 
  Caption Version   CC1, CC2, CC3, CC4 
 Low Power Mode     Off, On, On By Lan 
 Network Settings  Wired Lan  Status Connect, Disconnect 
   DHCP On, Off 
   IP Address 0~255, 0~255, 0~255, 0~255 
   Subnet Mask 0~255, 0~255, 0~255, 0~255 
   Default Gateway 0~255, 0~255, 0~255, 0~255 
   DNS Server 0~255, 0~255, 0~255, 0~255 
   Apply  
  Wireless Lan  Status Connect, Disconnect 
   SSID Refresh, Other 
   SSID Display On, Off 
   IP Address 0~255, 0~255, 0~255, 0~255 
   Connection Mode AP, Infrastructure 
   Apply  
  Remote Desktop  Account  
   Password  
   Connection Mode AP, Infrastructure 
  Projection Login 
Code 
  On, Off 
  Broadcasting  Broadcasting  On, Off 
   Channel 2~25 
   IP Address  
  AMX Device 
Discovery 
  On, Off 
  MAC Address   xx.xx.xx.xx.xx.xx 
 Reset All Settings     Reset, Cancel 
 Air Filter Timer 
Reset 
    Yes, No 
 Remote ID     Default, 1, 2, 3, 4, 5, 6, 7  
						

							 
– 25 – 
MAIN MENU  SUB MENU     SETTINGS 
INFORMATION  Source      
 Picture Mode      
 Lamp Mode      
 Resolution      
 3D Info      
 Lamp Hour 
(Normal, ECO, 
Total) 
     
 Air filter hour      
 Firmware Version      
 Remote ID      
 S/N      
 
 
  
						

							— 26 — 
PICTURE >> Basic Menu 
Press the MENU button to open the OSD menu. Press the cursor ◄ / ► buttons to move to the PICTURE 
>> Basic menu. Press the cursor ▲ / ▼ buttons to move up and down in the PICTURE >> Basic menu. 
Press the cursor ◄ / ► buttons to change values for settings. 
Note: 
Customizing the settings in PICTURE >> Basic menu is only available in User 1 / 2 mode. 
 
ITEM DESCRIPTION 
Display Mode 
Press the cursor ◄ / ► buttons to set the display mode.  
Note: The DISCOM SIM mode simulates the grayscale/gamma performance of the 
equipment used for Digital Image and Communication in Medicine(DICOM). 
Important: This display mode should NEVER be used for medical diagnosis; it is 
for education/training purpose only. 
Brightness Press the cursor ◄ / ► buttons to adjust the display brightness. 
Contrast Press the cursor ◄ / ► buttons to adjust the display contrast. 
Coloê 
Press the cursor ◄ / ► buttons to adjust the video saturation. 
Note: This function is only available when Component, Video or S-Video input 
source is selected. 
Tint 
Press the cursor ◄ / ► buttons to adjust the video tint/hue. 
Note: This function is only available when Component, Video or S-Video with 
NTSC system input source is selected. 
Sharpness 
Press the cursor ◄ / ► buttons to adjust the display sharpness. 
Note: This function is only available when Component, Video or S-Video input 
source is selected. 
Reset Picture Settings Press the ENTER button to reset Current or All settings to default values.  
						

							 
– 27 – 
PICTURE >> Advanced Menu 
Press the MENU button to open the OSD menu. Press the cursor ◄ / ► buttons to move to the  
PICTURE >> Advanced menu. Press the cursor ▲ / ▼ buttons to move up and down in the  
PICTURE >> Advanced menu. Press the cursor ◄ / ► buttons to change values for settings. 
 
ITEM DESCRIPTION 
Brilliant Color Press the cursor ◄ / ► buttons to set the brilliant color.  
Color Temperature Press the cursor ◄ / ► buttons to set the color temperature. 
Wall Color Press the cursor ◄ / ► buttons to select different wall color setting. 
Gamm~ Press the cursor ◄ / ► buttons to adjust the gamma correction of the display. 
HSG Adjustment Press the ENTER button to enter the HSG Adjustment sub menu. See HSG 
Adjustment on page 28. 
User Color Temp Press the ENTER button to enter the User Color Temp sub menu. See User Color 
Temp on page 28. 
White Balance Press the ENTER button to enter the White Balance sub menu.  
See White Balance on page 29.  
						

							— 28 — 
HSG Adjustment 
Press the ENTER button to enter the HSG Adjustment sub menu. 
 
ITEM DESCRIPTION 
Primary Color Press the cursor ◄ / ► buttons to set the Primary Color. 
Hue Press the cursor ◄ / ► buttons to adjust the Hue. 
Saturation Press the cursor ◄ / ► buttons to adjust the Saturation. 
Gain Press the cursor ◄ / ► buttons to adjust the Gain. 
User Color Temp 
Press the ENTER button to enter the User Color Temp sub menu. 
 
ITEM DESCRIPTION 
White Gain Red Press the cursor ◄ / ► buttons to adjust the White Gain Red. 
White Gain Green Press the cursor ◄ / ► buttons to adjust the White Gain Green. 
White Gain Blue Press the cursor ◄ / ► buttons to adjust the White Gain Blue.  
						

							 
– 29 – 
White Balance 
Press the ENTER button to enter the White Balance sub menu. 
 
ITEM DESCRIPTION 
Red Gain Press the cursor ◄ / ► buttons to adjust the Red Gain. 
Green Gain Press the cursor ◄ / ► buttons to adjust the Green Gain. 
Blue Gain Press the cursor ◄ / ► buttons to adjust the Blue Gain. 
Red Offset Press the cursor ◄ / ► buttons to adjust the Red Offset. 
Green Offset Press the cursor ◄ / ► buttons to adjust the Green Offset. 
Blue Offset Press the cursor ◄ / ► buttons to adjust the Blue Offset.  
						

							— 30 — 
DISPLAY Menu 
Press the MENU button to open the OSD menu. Press the cursor ◄ / ► buttons to move to the DISPLAY 
menu. Press the cursor ▲ / ▼ buttons to move up and down in the DISPLAY menu. Press the cursor  
◄ / ► buttons to change values for settings. 
 
ITEM DESCRIPTION 
Aspect Ratio Press the cursor ◄ / ► buttons to set the ~spect êatio. 
Note: Without support when 3D mode activated. 
Vertical Keystone Press the cursor ◄ / ► buttons to adjust the vertical âeystone. 
Horizontal Keystone Press the cursor ◄ / ► buttons to adjust the horizontal âeystone. 
Note: Without support when 3D mode activated. 
4 Corner 
Press the ENTER button to enter the 4 Corner sub menu. See 4 Corner on page 
31. 
Note: Without support when 3D mode activated. 
Pincushion 
Press the ENTER button to enter the Pincushion sub menu. See Pincushion on 
page 32. 
Note: Without support when 3D mode activated. 
PC Detail Adjustment Press the ENTER button to enter the PC Detail Adjustment sub menu. See PC 
Detail Adjustment on page 33. 
3D Setting Press the ENTER button to enter the 3D Setting sub menu. See 3D Setting on 
page 34. 
Digital Zoom 
Press the cursor ◄ / ► buttons to adjust the digital zoom. 
Note:  
1. Without support when 3D mode activated. 
2. Resync signal will adjust digital zoom to 0 automatically. 
3. Aspect ratio adjustment will make digital zoom back to 0 automatically. 
4. Signal re-sync will make digital zoom back to 0. 
5. Only 0~8 is allowed to adjust for Video/YUV signal.  
						

							 
– 31 – 
4 Corner 
Press the ENTER button to enter the 4 Corner sub menu. 
1. Press the cursor ▲ / ▼ / ◄ / ► buttons to select a corner and press ENTER. 
 
2. Press the cursor ▲ / ▼ buttons to adjust vertical and press the cursor ◄ / ► buttons to 
adjust horizontal. 
3. Press ENTER to save the settings. 
    
						

							— 32 — 
Pincushion 
Press the ENTER button to enter the Pincushion sub menu. 
1. Press the cursor ▲ / ▼ buttons to select one or both side and press ENTER. 
 
Note: 
Only one Pincushion setting will be stored so if you want to change from the previous direction to 
the other, the notice message will pop-up to remind you to reset the previous Pincushion setting. 
 
2. Press the cursor ▲ / ▼ / ◄ / ► buttons to adjust the desired side convex or concave. 
3. Press ENTER to save the settings. 
      
						

							 
– 33 – 
PC Detail Adjustment 
Press the ENTER button to enter the PC Detail Adjustment sub menu. 
Note: 
Customizing the settings in PC Detail Adjustment menu is only available when PC input source 
(analog RGB) is selected. 
 
ITEM DESCRIPTION 
Auto Press the ENTER/AUTO buttons on the control panel or the ENTER/AUTO buttons on 
the remote control to automatically adjust frequency, phase, and position. 
Frequency Press the cursor ◄ / ► buttons to adjust the A/D sampling number. 
Phase Press the cursor ◄ / ► buttons to adjust the A/D sampling clock. 
Horizontal Position Press the cursor ◄ / ► buttons to adjust the display position right or left. 
Vertical Position Press the cursor ◄ / ► buttons to adjust the display position up or down. 
Note:  
Some signals may take time to display or may not be displayed correctly. 
If the Auto Adjust operation cannot optimize the PC signal, try to adjust Frequency and Phase 
manually.