Vivitek D858wtpb User Manual

							 
 
  Preface 
Advanced Feature 
Press the Menu button to open the 
OSD menu. Press  ◄► to move to the  Installation II menu. 
Press  ▲▼ to move to the  Advanced menu and then press  Enter or ►. Press  ▲▼ to move up and 
down in the  Advanced menu. Press  ◄► to change values for setting. 
 
ITEM DESCRIPTION 
OSD Menu Setting  Press Enter / 
► to enter the OSD setting menu. See page  32 for more information on  OSD 
Menu Setting . 
Peripheral Test  Press Enter/ 
► to enter the Peripheral Test menu. See page  32 for more information on 
Peripheral Test . 
Lamp Hour Reset  After replacing the lamp, this item should be reset. See page 
33 for more information on Lamp 
Hour Reset . 
Low Power Mode  Press ◄► to turn Low Power Mode on or off. 
3D Press Enter/ ► to enter the 3D menu. See page  34 for more information on  3D setting.. 
RS232  Press 
◄► to select RS232 (remote) or Network (LAN) mode depending on projector connec-
tion method. 
Network  Press  (Enter) / 
► to enter the Network menu. See page  35 for more information on 
Network . 
Note: 
To enjoy the 3D function, fi rst enable the Play Movie in 3D setting found in your DVD  
device under the 3D Disc Menu. 
 
– 31  –  
						

							DLP Projector—User’s Manual 
OSD Menu Setting  
 
ITEM DESCRIPTION 
Menu Position Press ◄► button to select different OSD location. 
Translucent Menu  Press ◄► button to select OSD background translucent level.  
Menu Display  Press ◄► button to select OSD timeout delay. 
Peripheral Test 
 
ITEM DESCRIPTION 
Remote Control Test  Press  (Enter) / ► to test the IR remote controller for diagnostic.  
Color Test  Press  (Enter) / ► to select different colors on screen. 
Button Test  Press  (Enter) / ► to test the button on keypad. 
USB Test  Press  (Enter) / 
► to test the USB connection with connected PC. 
Note: Not available in special model 
—  32 —  
						

							 
 
  Preface 
Lamp Hour Reset 
 
Please refer to 
Resetting the Lamp  on page 44 to reset the lamp hour counter. 
 
–  33  –  
						

							DLP Projector—User’s Manual 
3D 
 
ITEM DESCRIPTION 
3D Press ◄► to select Off, DLP-Link or IR. 
3D Sync Invert  Press ◄► to turn 3D Sync Invert On or Off. 
 
Note: 
1.  The 3D OSD menu item is gray if there is no  appropriate 3D source. This is the default setting. 
2.  When the projector is connected to an appropria te 3D source, the 3D OSD menu item is enabled for 
selection. 
3.  Use 3D glasses to view a 3D image. 
4.  You need 3D content from a 3D DVD or 3D media file. 
5. You need to enable the 3D source (some 3D DVD  content may have a 3D on-off selection feature). 
6. You need DLP link 3D or IR 3D shutter glasses. With IR 3D shutter glasses, you need to install a 
driver on your PC and connect a USB emitter. 
7.  The 3D mode of the OSD needs to match the type of glasses (DLP link or IR 3D). 
8.  Power on the glasses. Glasses normally have a power on -off switch.  
Each type of glasses has their own  configuration instructions. Please follow the configuration instruc-
tions that come with your glasses to finish the setup process. 
 
Note:  
Since different types of glass (DLP link or IR shutter glass) have their own setting instructions, 
Please follow the guide to finish the setup process. 
— 34 —  
						

							 
 
  Preface 
Network 
 
ITEM DESCRIPTION 
Network State 
Displays the network connection status. 
DHCP  Press 
◄► to turn DHCP On or Off.  
Note:  If you select DHCP Off, complete the IP  Address, Subnet Mask, Gateway, and DNS 
fields. 
IP Address   Enter a valid IP address if DHCP is turned off. 
Subnet Mask  Enter a valid Subnet Mask if DHCP is turned off. 
Gateway Enter a valid Gateway address if DHCP is turned off. 
DNS  Enter a valid DNS name if DHCP is turned off. 
Apply Press  (Enter) / ► to confirm settings. 
 
 
– 35  –  
						

							DLP Projector—User’s Manual 
For simplicity and ease of operation, the projector provides diverse networking and remote management 
features. 
The LAN/RJ45 function of the projector through a network, such as remotely manage: Power On/Off, 
Brightness and Contrast settings. Also, projector stat us information, such as: Video-Source, Sound-Mute, 
etc
. 
 
LAN_RJ45 
1.  Connect an RJ45 cable to RJ45 ports on the projector and the PC (Laptop). 
 
2.  On the PC (Laptop), select  Start → Control  Panel →  Network Connections . 
 
— 36 —  
						

							 
 
  Preface 
3. Right-click on 
Local Area Connection , and select Properties. 
 
4. In the  Properties  window, select the  General tab, and select  Internet Protocol (TCP/IP) . 
5. Click  Properties . 
 
6. Click  Use the following IP address  and fill in the IP address and Subnet mask, then click  OK. 
 
– 37  –  
						

							DLP Projector—User’s Manual 
7. Press the Menu button on the projector. 
8. Select  Installation II  →  Advanced  → Network . 
9.  After getting into  Network, input the following: 
`  DHCP: Off 
`  IP Address: 10.10.10.10 
`  Subnet Mask: 255.255.255.0 
`  Gateway: 0.0.0.0 
`  DNS Server: 0.0.0.0 
10. Press 
 (Enter) / ►  to confirm settings. 
Open a web browser  
(for example, Microsoft Internet Explorer  with Adobe Flash Player 9.0 or higher). 
 
11.  In the Address bar, input  the IP address: 10.10.10.10. 
12. Press 
 (Enter) / ► . 
The projector is setup for remote managemen t. The LAN/RJ45 function displays as follows. 
 
—  38 —  
						

							 
 
  Preface 
 
CATEGORY ITEM INPUT-LENGTH 
IP Address 
14 
IP ID 3 Crestron Control 
Port 5 
Projector Name 10 
Location 9 Projector 
Assigned To 8 
DHCP (Enabled) (N/A) 
IP Address 15 
Subnet Mask 15 
Default Gateway 15 
Network Configuration 
DNS Server 15 
Enabled (N/A) 
New Password 15 User Password 
Confirm 15 
Enabled (N/A) 
New Password 15 Admin Password 
Confirm 15 
 
For more information, please visit  http://www.crestron.com. 
 
 
 
 
 
 
–  39  –  
						

							DLP Projector—User’s Manual 
Factory Reset 
Press the cursor ▲▼ button to move up and down in the  Installation II menu. Select the  Factory 
Reset  sub menu and press 
 (Enter) /  ► to reset all the menu items to the factory default values 
(except Language and Security Lock). 
 
Status 
Press the cursor ▲▼  button to move up and down in the  Installation II menu. Select the   
Installation II sub menu and press 
 (Enter) /  ► to enter the  Status sub menu.
 
 
ITEM DESCRIPTION 
Active Source  Display the activated source. 
Video Information  Displays resolution/video information for RGB source and color standard for Video source. 
Lamp Hours  Lamp hour used information is displayed. Eco and Normal counters are separated. 
 
 
— 40 —