Vivitek D795wt User Manual

DLP Projector – User’s Manual 
 
 
–  33  – 
Lamp Hour Reset 
 
Please refer to  Resetting the Lamp  on page 42 to reset the lamp hour counter. 
 
3D 
 
ITEM DESCRIPTION 
3D Press  ◄► to select Off, DLP-Link or IR. 
3D Sync Invert  Press  ◄► to turn 3D Sync Invert On or Off. 
 
Downloaded From projector-manual.com Vivitek Manuals 

DLP Projector – User’s Manual 
 
 
Network 
 
ITEM DESCRIPTION 
Network State Displays the network connection status. 
Press  ◄► to turn DHCP On or Off.  
DHCP Note:  If you select DHCP Off, complete the IP  Address, Subnet Mask, Gateway, and DNS 
fields. 
IP Address  Enter a valid IP a ddress if DHCP is turned off. 
Subnet Mask Enter a valid Subnet Mask if DHCP is turned off. 
Gateway Enter a valid Gateway address if DHCP is turned off. 
DNS Enter a valid DNS name if DHCP is turned off. 
Apply Press...

DLP Projector – User’s Manual 
 
 
For simplicity and ease of operation, the projector provides diverse networking and remote management 
features. 
The LAN/RJ45 function of the pr ojector through a network, such as remotely manage: Power On/Off, 
Brightness and Contrast settings. Also, projector stat us information, such as: Video-Source, Sound-Mute, 
etc
. 
 
LAN_RJ45 
1.  Connect an RJ45 cable to RJ45 ports on the projector and the PC (Laptop). 
 
2.  On the PC (Laptop), select  Start → Control...

DLP Projector – User’s Manual 
 
 
3. Right-click on  Local Area Connection , and select Properties. 
 
4. In the Properties  window, select the  General tab, and select  Internet Protocol (TCP/IP) . 
5. Click Properties . 
 
6. Click Use the following IP address  and fill in the IP address and Subnet mask, then click  OK. 
 
– 36 –  
Downloaded From projector-manual.com Vivitek Manuals 

DLP Projector – User’s Manual 
 
 
7. Press the  Menu button on the projector. 
8. Select Installation II  →  Advanced→  Network. 
9.  After getting into  Network, input the following: 
` DHCP: Off 
` IP Address: 10.10.10.10 
` Subnet Mask: 255.255.255.0 
` Gateway: 0.0.0.0 
` DNS Server: 0.0.0.0 
10. Press  (Enter) / ►  to confirm settings. 
Open a web browser  
(for example, Microsoft Internet Explorer  with Adobe Flash Player 9.0 or higher). 
 
11.  In the Address bar, input the IP address:...

DLP Projector – User’s Manual 
 
 
 
 
CATEGORY ITEM INPUT-LENGTH 
IP Address 14 
– 38 –  
IP ID 2 Crestron Control 
Port 5 
Projector Name 10 
Location 9 Projector 
Assigned To 8 
DHCP (Enabled) (N/A) 
IP Address 15 
Subnet Mask 15 Network Configuration 
Default Gateway 15 
DNS Server 15 
Enabled (N/A) 
New Password 15 User Password 
Confirm 15 
Enabled (N/A) 
New Password 15 Admin Password 
Confirm 15 
For more information, please visit http://www.crestron.com. 
Downloaded From projector-manual.com...

DLP Projector – User’s Manual 
 
 
Factory Reset 
Press the cursor ▲▼  button to move up and down in the  Installation II menu. Select the  Factory 
Reset  sub menu and press 
 (Enter) /  ► to reset all the menu items to the factory default values 
(expect Language and Security Lock). 
 
 
Status 
Press the cursor ▲▼  button to move up and down in the  Installation II menu. Select the   
Installation II sub menu and press 
 (Enter) /  ► to enter the  Status sub menu.
 
 
ITEM DESCRIPTION 
Active Source...

DLP Projector – User’s Manual 
 
 
– 40 –  
MAINTENANCE AND SECURITY 
Replacing the Projection Lamp 
The projection lamp should be replaced when it burns out. It should only be r eplaced with a certified 
replacement part, which you can order from your local dealer.  
Important: 
a.  The projection lamp used in this product contains a small amount of mercury. 
b.  Do not dispose this product  with general household waste. 
c. Disposal of this product must be carried out in  accordance with the...

DLP Projector – User’s Manual 
 
 
 
 
3. Remove the two screws from 
the lamp module. 
4. Lift the module handle up. 
5. Pull firmly on the module  
handle to remove the lamp 
module. 
 
6. Reverse steps 1 to 5 to install 
the new lamp module.  
While installing, align the 
lamp module with the  
connector and ensure it is level 
to avoid damage. 
Note: The lamp module must 
sit securely in place and the 
lamp connector must be con-
nected properly before 
tightening the screws. 
 
 
–  41  –...

DLP Projector – User’s Manual 
 
 
– 42 –  
Resetting the Lamp 
After replacing the lamp, you should reset the lamp  hour counter to zero. Refer to the following: 
1.  Press the  MENU button to open the 
OSD menu. 
2.   Press the cursor  
{
y button to move 
to the  Installation II  menu. Press the 
cursor button to move down to  
Advanced . 
3.  Press the cursor  
z
x button to move 
down to  Lamp Hour Reset . 
4.  Press the cursor  
y or Enter button.  
A message screen appears. 
5.   Press  
z
x
{
y...