Vivitek D795wt User Manual

DLP Projector – User’s Manual 
 
 
–  13  – 
Setting an Access Password (Security Lock) 
You can use the four (arrow) buttons  to set a password and prevent unauthorized use of the projector. 
When enabled, the password must be entered  after you power on the projector. (See Navigating the 
OSD  on page 18 and  Setting the OSD Language  on page 19 for help on using OSD menus.) 
Important: 
Keep the password in a safe place.  Without the password, you will not be able to use the projector. 
If you lose...

DLP Projector – User’s Manual 
 
 
5.  You can use the cursor buttons  ▲▼◄► 
either on keypad or IR remote control for 
password entry. You can use any 
combination including the same arrow five 
times, but not less than five. 
 
Press the cursor buttons in any order to set 
the password. Push the  MENU button to 
exit the  dialog box. 
 
6.  The password confirm menu appears when 
user presses the power-on key in case the 
Security Lock  is enabled.  
Enter the password in the order you set it 
at step...

DLP Projector – User’s Manual 
 
 
Adjusting the Projector Level 
Take note of the following when setting up the projector: 
•  The projector table or stand should be level and sturdy. 
• Position the projector so that it is perpendicular to the screen. 
• Remove the Back Foot Holder on the rear adjuster foot before adjusting the projection  
angle. 
• Ensure the cables are in a safe location. You could trip over them.  
 
1.  To raise the level of the projector, twist 
the adjusters clockwise. 
 
2....

DLP Projector – User’s Manual 
 
 
Adjusting the Keystone 
1.  
Volume
+
-
Use the  KEYSTONE  
buttons the remote control 
to correct image-trapezoid 
(wider top or bottom)  
effect. 
 
2.  The keystone control  
appears on the display. 
– 16 –  
Downloaded From projector-manual.com Vivitek Manuals 

DLP Projector – User’s Manual 
 
 
–  17  – 
Adjusting the Volume 
1.   Press the  Volume +/-   
buttons on the remote 
control.  
The volume control  
appears on the display. 
Volume
+
- 
 
2.   Press the  MUTE button to 
turn off the volume 
 
 
Downloaded From projector-manual.com Vivitek Manuals 

DLP Projector – User’s Manual 
 
 
 
ON-SCREEN DISPLAY (OSD) MENU SETTINGS 
OSD Menu Controls 
The projector has an OSD that lets you ma ke image adjustments and change various settings.  
Navigating the OSD 
You can use the remote control curs or buttons or the buttons on the top of the projector to navigate 
and make changes to the OSD. The following illu stration shows the corresponding buttons on the 
projector. 
 
1.  To enter the OSD, press the  MENU button.  
2.  There are five menus. Press 
the...

DLP Projector – User’s Manual 
 
 
Setting the OSD Language 
Set the OSD language to your pr eference before continuing. 
1.  Press the  MENU button. Press the cursor  ◄► button to navigate to Installation I. 
 
2.  Press the cursor  ▲▼ button until  Language is highlighted.  
 
3.  Press the cursor  ◄► button until the language you want is highlighted.  
4.  Press the  MENU button twice to close the OSD.   
– 19  – 
Downloaded From projector-manual.com Vivitek Manuals 

DLP Projector – User’s Manual 
 
 
OSD Menu Overview 
Use the following illustration to quickly find a se tting or determine the range for a setting. 
Image
Brightness
Contrast 
Sharpness
PC, MAC, Video, Chart, 
B&W
Computer
Horizontal Position
Vertical Position
Frequency
Tracking
Auto Image
Installation I
Blank 
ScreenBlack, Red, Green, Blue, 
White
Video / 
Audio
Video 
Saturation
Video Tint
Video 
Overscan
Front, Rear, Ceiling, Rear + 
Ceiling
Film Mode
English, French, German, Spanish, Portuguese,...

DLP Projector – User’s Manual 
 
 
OSD Sub-Menu Overview 
 
–  21  – 
Downloaded From projector-manual.com Vivitek Manuals 

DLP Projector – User’s Manual 
 
 
Image Menu  
Press the MENU  button to open the  OSD menu. Press the cursor  ◄► button to move to the  Image 
Menu. Press the cursor  ▲▼ button to move up and down in the  Image menu. Press  ◄► to change 
values for settings. 
 
ITEM DESCRIPTION 
Display Mode Press the cursor  ◄► button to set the Display Mode.  
Brilliant Color Press the cursor  ◄► button to adjust the Brilliant Color value. 
Brightness Press the cursor ◄►  button to adjust the display brightness....