Vivitek D795wt User Manual

DLP Projector – User’s Manual 
 
 
 Rear view 
12 34
56
7
89
12 11
1
0 
ITEM LABEL DESCRIPTION SEE PAGE: 
Connect the RGB CABLE to a display 
(Loop Thru only for VGA IN-1) 1.  VGA OUT 
2.  RS-232 Connect RS-232 serial port cable for remote control 
Connect the RGB CABLE from a computer and  
components 3.  VGA – 1 
Connect the RGB CABLE from a computer and  
components 4.  VGA – 2 9
5.  RJ – 45 Connect a LAN CABLE from Ethernet 
6.  S-VIDEO IN Connect the S-VIDEO CABLE from a video device 
7.  VIDEO IN...

DLP Projector – User’s Manual 
 
 
Bottom view 
70.00110.00
126.00228.00
20.00
56.00
146.00
236.00100.0240.0
12 3
3 3 2
 
ITEM LABEL DESCRIPTION SEE PAGE: 
441.  Security bar Helps protect the projector from unauthorized use 
2.  Tilt adjustors Rotate adjusters lever to adjust angle position 
3.  Ceiling support holes Contact your dealer for information on mounting the projector on a ceiling 
 
Note: 
When installing, ensure that you us
e only UL Listed ceiling mounts. 
For ceiling installations, use...

DLP Projector – User’s Manual 
 
 
Remote Control Parts 
 
 
Important: 
1.  Avoid using the projector with bright fluoresc ent lighting turned on. Certain high-frequency fluo-
rescent lights can disrupt remote control operation. 
 
2. Be sure nothing obstructs the path between the re mote control and the projector. If the path be-
tween the remote control and the projector is obstructed, you can bounce the signal off certain 
reflective surfaces such as projector screens. 
 
3. The buttons and keys on...

DLP Projector – User’s Manual 
 
 
– 6 –  
 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  IR transmitter  Transmit s signals to projector 
2.  Status LED  Lights when the remote control is used 
3.  Laser  Press to operate the on-screen pointer 
4.  Up  Up arrow when connect ed through USB to a PC 
5.  Right  Right arrow when connected through USB to a PC 
6.  Down  Down arrow when conn ected through USB to a PC 
7.  Page Down  Page down when connected through USB to a PC 
8.  Up cursor  
9.  Right cursor...

DLP Projector – User’s Manual 
 
 
–  7 –  
Remote Control Operating Range 
The remote control uses infrared transmission to cont rol the projector. It is not necessary to point the 
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or 
the rear of the projector, the re mote will function well within a radi us of about 7 meters (23 feet) and 
15 degrees above or below the projector level. If the pr ojector does not respond to the remote control, 
move a...

DLP Projector – User’s Manual 
 
 
 
SETUP AND OPERATION 
Inserting the Remote  Control Batteries  
– 8 – 
1.  Remove the battery compartment cover 
by sliding the cover in the direction of 
the arrow. 
 
2.  Insert the battery with the positive side 
facing up. 
 
3.  Replace the cover. 
 
 
Caution: 
1. Only use AAA batteries (Alkaline batteries are recommended). 
 
2. Dispose of used batteries accordi ng to local ordinance regulations.  
 
3. Remove the batteries when not usi ng the projector for...

DLP Projector – User’s Manual 
 
 
–  9  – 
Connecting Input Devices 
A PC or notebook computer and video devices can be connected to the projector at the same time. Video 
devices include DVD, VCD, and VHS players, as we ll as movie camcorders and digital still cameras. 
Check the user manual of the connecting device to  confirm it has the appropriate output connector.  
ABCDEFG
HIJKL 
ITEM LABEL DESCRIPTION 
A VGA OUT Connect the RGB CABLE to a display 
(Loop Thru only for VGA IN-1) 
B RS-232  Connect...

DLP Projector – User’s Manual 
 
 
– 10 –  
ITEM LABEL DESCRIPTION 
K AUDIO IN  Connect an audio cable from the input device 
L AUDIO OUT  Connect an audio cable from the output device 
！Warning: 
As a safety precaution, disconnect all power to  the projector and connecting devices before making 
connections. 
Downloaded From projector-manual.com Vivitek Manuals 

DLP Projector – User’s Manual 
 
 
–  11  – 
Starting and Shutting  down the Projector 
1.  Connect the power cord to the projector. 
Connect the other end to a wall outlet. 
The  POWER  LED on the projector 
light. 
2.   Turn on the connected devices.  
3.  Ensure the  POWER LED displays a 
solid orange. Then press the  POWER 
button 
of the remote to turn on the pro-
jector.  
 
The projector splash screen displays and 
connected devices are detected. 
 
See  Setting an Access Password 
(Security...

DLP Projector – User’s Manual 
 
 
– 12 –  
5.  When the “Power Off? /Press Power 
again” message appears, press the 
POWER  button. The projector turns 
off. 
 
Caution: 
Do not unplug the power cord until the POWE R LED change to orange–indicating the projector 
has cooled down. 
 
 
 
Downloaded From projector-manual.com Vivitek Manuals