ViewSonic Projector Pro9500 User Manual

16
ViewSonic
  Pro9500
Setting up
• The HDMI port of this model is compatible with HDCP (High-band -
width Digital Content Protection) and therefore capable of displaying a video 
signal from HDCP compatible DVD players or the like.
- 
 
The HDMI supports the following video signals:
480i@60,480p@60,576i@50,576p@50,720p@50/60,1080i@50/60,1080p@50/60 
- 
 
This projector can be connected with another equipment that has HDMITM 
connector, but with some equipment the projector may not work properly,...

17
ViewSonic
  Pro9500
Setting up
Speakers
(with an amplifier)
Wired 
remote 
control
(optional)
Monitor
Microphone  system
Connecting with your devices (continued)
• If a loud feedback noise is produced from the speaker, move the 
microphone away from the speaker.  NOTE
• You can connect a dynamic microphone to the  MIC port with a 3.5 mm mini-plug.
In that case, the built-in speaker outputs the sound from the microphone, even 
while the sound from the projector is output. You can input line level...

18
ViewSonic
  Pro9500
Connecting to a power supply
1.Put the connector of the power cord into the 
AC IN (AC inlet) of the projector.
2.Firmly plug the power cord’s plug into the 
outlet. In a couple of seconds after the 
power supply connection, the POWER 
indicator will light up in steady orange.
►Please use extra caution when connecting the power cord, as 
incorrect or faulty connections may result in fire and/or electrical shock.
• 
 
Only use the power cord that came with the projector. If it is...

19
ViewSonic
  Pro9500
30°3m30°
(approx.)
Remote control
About the remote control signal
The remote control works with the projector’s remote 
sensor. This projector has a remote sensor on the front.
The sensor senses the signal within the following range 
when the sensor is active: 60 degrees (30 degrees to the left and right of the sensor) 
within 3 meters about.
Installing the batteries
Please insert the batteries into the remote control before using it. If the remote control 
starts to malfunction,...

20
ViewSonic
  Pro9500
Changing the frequency of  remote control signal
The accessory remote control has the two choices on signal 
frequency Mode 1:NORMAL and Mode 2:HIGH. If the remote control 
does not function properly, attempt to change the signal frequency.
In order to set the Mode, please keep pressing the combination of 
two buttons listed below simultaneously for about 3 seconds.
Using as a simple PC mouse & keyboard
The accessory remote control works as a simple mouse 
and keyboard of the...

21
ViewSonic
  Pro9500
VIDEODOC.CAMERAKEYSTONEASPECT SEARCH
BLANK
MUTEMY BUTTONPOSITIO N1 2ESC ENTERMENURESET
COMPUTER
MY SOURCE/A
UTOM AGNIFYPAGE
      UPVOLUM EDOWNー
ONOFF＋
F
REEZE
1.Make sure that the power cord is firmly and 
correctly connected to the projector and the 
outlet.
Turning on the power
2.Make sure that the POWER indicator is 
steady orange. Then remove the lens cover.
3.Press STANDBY/ON button on the 
projector or the remote control.
The projection lamp will light up and  POWER...

22
ViewSonic
  Pro9500
Operating
1.
Adjusting the volume
Use the VOLUME +/VOLUME - buttons to adjust the volume.
A dialog will appear on the screen to aid you in adjusting the 
volume. If you do not do anything, the dialog will automatically 
disappear after a few seconds.
●   When 
 is selected for current picture input port, the volume adjustment is 
disabled. Please see AUDIO SOURCE item of AUDIO menu.
● 
 
Even if the projector is in the standby mode, the volume is adjustable when 
both of the...

23
ViewSonic
  Pro9500
VIDEODOC.CAMERA
KEYSTONE
ASPECT SEARCH
BLANK
M\fTE
MY B\fTTO N
POSITION
1 2
ESC ENTER
MEN\f
RESET
COMP\fTER
MY SO\fRCE\bA\fTO
MAGNIF
YPAGE
      \fPVOL\fME
DOWNo
ONOF
F
9×
FREEZE
1.Press VIDEO button on the remote control. 
Each time you press the button, the projector switches its 
input port from the current port as below.
Selecting an input signal (continued)
●  While ON is selected for AUTO SEARCH item in OPTION 
menu, the projector will keep checking every port sequentially...

24
ViewSonic
  Pro9500
Operating
Selecting an aspect ratio
● ASPECT button does not work when no proper signal is inputted.
● NORMAL mode keeps the original aspect ratio setting.
1.Press SEARCH button on the remote control.
The projector will start to check its input ports as below in 
order to find any input signals.
When an input is found, the projector will stop searching 
and display the image. If no signal is found, the projector will 
return to the state selected before the operation.
Searching an...

25
ViewSonic
  Pro9500
Operating
Adjusting the projector’s elevator
When the place to put the projector is slightly uneven 
to the left or right, use the elevator feet to place the 
projector horizontally. 
Using the feet can also tilt the projector in order to 
project at a suitable angle to the screen, elevating the 
front side of the projector within 12 degrees.
This projector has 2 elevator feet and 2 elevator buttons. 
An elevator foot is adjustable while pushing the elevator 
button on the same...