ViewSonic Projector Pro8510L User Manual

36
Color Management
Only in permanent installations with controlled
 lighting levels such as boardrooms, lecture 
theaters, or home theaters, should color management be considered. Color management 
provides fine color control adjustment to allo w for more accurate color reproduction, should 
you require it.
If you have purchased a test disc which contains  various color test patterns and can be used 
to test the color presentation on monitors, TV s, projectors, etc., you can project any image 
from the...

37
2. Press Enter or wait for 3 seconds to activate the timer.
3. To display the  Presentation Timer  page, select Advanced.
• Using the OSD menu
1. Go to the  BASIC > Presentation Timer  menu.
2. Press  Enter to display the  Presentation Timer  page.
3. Highlight  Timer Period and decide the time period by pressing  /. The length of 
time can be set from 1 to 5 minutes in 1- minute increments and 5 to 240 minutes in 5-
minute increments.
If the timer is already on, the timer will restart whenever the...

38
You can set the blank time in the BASIC > Blank Timer menu to let the projector return 
the image automatically after a period of time when there is no action taken on the blank 
screen. 
Once Blank is pressed, the projector enters Eco mode automatically.
CAUTION
Do not block the projection lens from projecting as this could cause the blocking object to 
become heated and deformed or even cause a fire.
Locking control keys
With the control keys on the projector locked , you can prevent your projector...

39
Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and temperature 
is between 5°C and 35°C. The projector will be over cooled, if you turn the mode on under 
such a condition.
To activate the  High Altitude Mode :
1. Open the OSD menu and go to the  SYSTEM > High 
Altitude Mode  menu.
2. Press  Enter and press  / to select  On. A 
confirmation message is displayed.
3. Highlight  Yes and press  Enter.
Operation under  High Altitude Mode  may cause a higher 
decibel operating...

40
5. Press  to select a 3D Sync setting and then press  Enter to confirm.
When the 3D Sync function is on:
• The brightness level of the projected image will decrease.
• The Color Mode cannot be adjusted.
• The Zoom function can only magnify the pictures to limited sizes.
If you discover the inversion of the 3D image depth, set the 3D Sync Invert function to “Invert” 
to correct the problem.
Controlling the projector through a LAN 
environment
The projector su pports Crestron® software. With correct...

41
2. Highlight LAN Control Settings  and press  /  to select  Static IP.
3. Contact your ITS administ rator for information on the Projector IP Address, Subnet 
Mask , Default Gateway , and DNS Server  settings.
4. Press   to select the item you want to modify and press  Enter.
5. Press  /  to move the cursor and the press  /  to enter the value.
6. To save the settings, press  Enter. If you do not want to save the settings, press  Exit.
7. Press   to highlight  Apply and press  Enter.
If the RJ45...

42
controllers of AMX connected to the same network. For the Details of AMX Device 
Discovery, visit the AMX web site at http://www.amx.com/.
4. If your projector is connected to a ne twork which supports Simple Mail Transfer 
Protocol (SMTP), you can conf igure it to alert you via email on significant events.
5. The Crestron (e-Control) page displays  the Crestron e-Control user interface. See 
About Crestron e-C ontrol® on page 44 for details.  

43
Please pay attention to the limitation of input length (including space and other punctuation 
keys) in the list blow:
 / > < $ % +      are prohibited.
Category ItemInput LengthMaximum Number 
of Characters
Network Settings Network
DHCP/Manual (N/A)
IP Address XXX.XXX.XXX.XXX
Subnet Mask XXX.XXX.XXX.XXX
Gateway XXX.XXX.XXX.XXX
DNS Server XXX.XXX.XXX.XXX
AMX device discovery (N/A)
Password Administrator (N/A)
New Password 4
Confirm Password 4
SNMP SysLocation 22
SysName 22
SysContact 22
Email Alert...

44
About Crestron e-Control®
1. The Crestron e-Control® page provides a variety of virtual keys to control the 
projector or adjust the projected pictures. 
i. These buttons function the same as the ones on the OSD menus or remote control.  See  2. IMAGE menu on page 55  and Projector on page 7 for details.
ii. To switch between input signals , click on your desired signal.
The Menu button can also be used to go back to previous OSD menus, exit and save menu 
settings.
The source list varies according to...

45
iii. You can adjust the LAN Control Settings .
iv. Once set, access to the remote network operation on this projector has been  password-protected.
v. Once set, access to the tools pa ge has been password-protected.
To prevent errors, only input the English alphabet and digits on the tools page.
After making the adjustments, press the Send button and the data will be saved for the 
projector.
vi. Press Exit to go back to the remote network operation page.
Please pay attention to the limi tation of...