ViewSonic Projector PJD8333s User Manual

 4
Rear View
Bottom View
Note
•
This projector can be used with a ceiling mount for support. The ceiling mount is not 
included in the package.
•Contact your dealer for information to mount the projector on a ceiling.
•When installing the unit, incorporate a readily accessible disconnect device in the fixed 
wiring, or connect the power plug to an easily accessible socket-outlet near the unit. If a 
fault should occur during operation of the unit, operate the disconnect device to switch 
the power supply...

 5
Using the Product
Control Panel
1. Power (Power LED indicator)
Refer to “LED Indicator Messages”.
2. TEMP (Temperature LED indicator)
Refer to “LED Indicator Messages”.
3. LAMP (Lamp LED indicator)
Refer to “LED Indicator Messages”.
4. Keystone/Arrow keys ( /Up,  /Down)
Manually correct distorted images resulting from an angled projection.
5. Four directional buttons
Use four directional buttons to select items or make adjustments to your  selection.
6. ENTER
Enter to sub-menu and confirm the menu...

 6
Connection Ports
1. AUDIO IN 2/MIC
Connect an audio output from video equipment / computer or Microphone to this 
jack.
Note: The function for switching to Audio in / Microphone in is in OSD menu.
2. AUDIO IN 1
Connect an audio output from video equipment or computer to this jack.
Note: 
AUDIO IN 1 jack can only play the sound from COMPUTER IN 1 signal.
3. S-VIDEO
Connect S-Video output from video equipment to this jack.
4. COMPUTER IN 1
Connect image input signal (analog RGB or component) to this...

 7
10. TYPE A USB
This connector supports USB flash drive and wireless dongle.
11. MINI USB
USB display supports computer connection via USB mini-B type to A type cable.
12. COMPUTER IN 2
Connect image input signal (analog RGB or component) to this jack.
13. VIDEO
Connect composite video output from video equipment to this jack.
14. DC 12V OUT
12V DC out
15. AUDIO OUT
Connect to a speaker or other audio input equipment. 

 8
Remote Control
1. Power
Turn the projector ON or OFF.
2. VGA
Switch between the COMPUTER IN 1 and COMPUTER IN 2 signal.
3. Auto Sync
Automatically determines the best picture timings for the displayed image.
4. Keystone/Arrow keys ( /Up,  /Down)
Manually correct distorted images resulting from an angled projection.
5. Left
When the On-Screen Display (OSD) menu is activated, the #4, #5, and #20 keys 
are used as directional arrows to select the desired menu items and to make 
adjustments.
6. My Button...

 9
12. Pattern
Display embedded test pattern.
13. Blank
Hide the screen picture.
14. D.Eco
Decreases the power consumption of the lamp by up to 70%.
Note: It takes some time to initiate this function. Make sure the projector has been 
turned on for more than 4 minutes.
15. Laser
Aim the remote at the viewing screen, press and hold this button to activate the 
laser pointer.
16. Source
Display the source selection bar.
17. Video
Switch input source to Composite/S-Video/HDMI by sequence.
18. Color Mode...

 10
Operating the Laser pointer
The laser beam is visible. It is necessary to press and 
hold LASER for continuous output.
The laser pointer is not a toy. Parents should be mindful of 
the dangers of laser energy and keep this remote control 
out of the reach of children.
Caution
•
Do not look into the laser light window or shine the laser light beam on yourself or 
others. See the warning messages on the back of the remote control prior to using it.
Using the remote mouse control
The capability of...

 11
Installing the Batteries
1. Open the battery cover in the 
direction shown.
2. Install batteries as indicated by the 
diagram inside the compartment.
3. Close the battery cover into position.
Caution
•
Risk of explosion if battery is replaced by an incorrect type.
•Dispose of used batteries according to the instructions.
•Make sure the plus and minus terminals are correctly aligned when loading a battery.
Note
•
Keep the batteries out of the reach of children. There is a danger of death by...

 12
Remote Control Operation
Point the remote control at the infrared remote sensor and press a button.
• Operating the projector from the
front
• Operating the projector from the 
rear
Note
•
Do not point the laser directly to the peoples eyes (especially small children). There is a 
danger of injury to the eyes.
•The remote control may not operate when there is sunlight or other strong light such as 
a fluorescent lamp shining on the remote sensor.
•Operate the remote control from a position where the...

 13
Connection
When connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly inserted.
Important
•
In the connections shown above, some cables may not be included with the projector 
(see Package Contents on page 2). They are commercially available from electronics 
stores.
•The connection illustrations above are for reference only. The rear connecting jacks...