ViewSonic Projector PJD8333s User Manual

							 4
Rear View
Bottom View
Note
•
This projector can be used with a ceiling mount for support. The ceiling mount is not 
included in the package.
•Contact your dealer for information to mount the projector on a ceiling.
•When installing the unit, incorporate a readily accessible disconnect device in the fixed 
wiring, or connect the power plug to an easily accessible socket-outlet near the unit. If a 
fault should occur during operation of the unit, operate the disconnect device to switch 
the power supply off, or disconnect the power plug.
1. Rear IR remote control sensor 2. AC power socket
3. Connection ports 4. Kensington lock
PJD8333s/PJD8633ws PJD7333/PJD7533w
1. Ceiling mount holes (M4*8) 2. Tilt-adjustment feet
1234
1
2 
						

							 5
Using the Product
Control Panel
1. Power (Power LED indicator)
Refer to “LED Indicator Messages”.
2. TEMP (Temperature LED indicator)
Refer to “LED Indicator Messages”.
3. LAMP (Lamp LED indicator)
Refer to “LED Indicator Messages”.
4. Keystone/Arrow keys ( /Up,  /Down)
Manually correct distorted images resulting from an angled projection.
5. Four directional buttons
Use four directional buttons to select items or make adjustments to your  selection.
6. ENTER
Enter to sub-menu and confirm the menu selection.
7. SOURCE
Display the source selection bar.
8. MENU/EXIT
Display or exit the on-screen display menus.
9. Power
Turn the projector on or off.
4 
6 5 
6
3 2 1 9 
7 4 
8 
						

							 6
Connection Ports
1. AUDIO IN 2/MIC
Connect an audio output from video equipment / computer or Microphone to this 
jack.
Note: The function for switching to Audio in / Microphone in is in OSD menu.
2. AUDIO IN 1
Connect an audio output from video equipment or computer to this jack.
Note: 
AUDIO IN 1 jack can only play the sound from COMPUTER IN 1 signal.
3. S-VIDEO
Connect S-Video output from video equipment to this jack.
4. COMPUTER IN 1
Connect image input signal (analog RGB or component) to this jack.
5. MONITOR OUT
Connect to a computer display, etc.
6. HDMI
Connect HDMI output from video equipment to this jack.
7. RS-232
When operating the projector via a computer, connect this to the controlling com-
puters RS-232C port.
8. TYPE B USB
This connector is for firmware update and mouse function support.
9. LAN
RJ45 connector for Ethernet connection.
12345678910
1112131415 
						

							 7
10. TYPE A USB
This connector supports USB flash drive and wireless dongle.
11. MINI USB
USB display supports computer connection via USB mini-B type to A type cable.
12. COMPUTER IN 2
Connect image input signal (analog RGB or component) to this jack.
13. VIDEO
Connect composite video output from video equipment to this jack.
14. DC 12V OUT
12V DC out
15. AUDIO OUT
Connect to a speaker or other audio input equipment. 
						

							 8
Remote Control
1. Power
Turn the projector ON or OFF.
2. VGA
Switch between the COMPUTER IN 1 and COMPUTER IN 2 signal.
3. Auto Sync
Automatically determines the best picture timings for the displayed image.
4. Keystone/Arrow keys ( /Up,  /Down)
Manually correct distorted images resulting from an angled projection.
5. Left
When the On-Screen Display (OSD) menu is activated, the #4, #5, and #20 keys 
are used as directional arrows to select the desired menu items and to make 
adjustments.
6. My Button
User definable key for customized function
7. Menu
Display or goes back to previous OSD menu.
8. Right mouse
Perform the right button of the mouse when mouse mode is activated.
9. Left mouse
Perform the left button of the mouse when mouse mode is activated.
10. Mouse
Switch between the normal and mouse modes.
11. Lock
Activate panel key lock.
4
5
7
9
11
12
10
3
8
6
4
13
14
15
16
17
18
19
24
25
20
21
29
22
23
26
28
27 
						

							 9
12. Pattern
Display embedded test pattern.
13. Blank
Hide the screen picture.
14. D.Eco
Decreases the power consumption of the lamp by up to 70%.
Note: It takes some time to initiate this function. Make sure the projector has been 
turned on for more than 4 minutes.
15. Laser
Aim the remote at the viewing screen, press and hold this button to activate the 
laser pointer.
16. Source
Display the source selection bar.
17. Video
Switch input source to Composite/S-Video/HDMI by sequence.
18. Color Mode
Select the picture setup mode.
19. Enter
Confirmed selections.
20. Right
When the On-Screen Display (OSD) menu is activated, the #4, #5, and #20 keys 
are used as directional arrows to select the desired menu items and to make 
adjustments.
21. Exit
Exits and saves menu settings.
22. Page Up
Perform page up function when mouse mode is activated.
23. Page Down
Perform page down function when mouse mode is activated.
24. Magnify
Magnifies the projected picture size.
25. Volume
Adjust the volume level.
26. Freeze
Freeze the projected image.
27. Mute
Toggles the projector audio between on and off.
28. Aspect
Select the display aspect ratio.
29. Timer
Activate Presentation Timer OSD menu. 
						

							 10
Operating the Laser pointer
The laser beam is visible. It is necessary to press and 
hold LASER for continuous output.
The laser pointer is not a toy. Parents should be mindful of 
the dangers of laser energy and keep this remote control 
out of the reach of children.
Caution
•
Do not look into the laser light window or shine the laser light beam on yourself or 
others. See the warning messages on the back of the remote control prior to using it.
Using the remote mouse control
The capability of operating your computer with the remote control gives you more 
flexibility when delivering presentations.
1. Connect the projector to your PC or notebook with a USB cable prior to using the
remote control in place of your computer’s mouse. See Connecting a computer
on page 14 for details.
2. Set the input signal to COMPUTER IN 1 or  COMPUTER IN 2.
3. Press Mouse on the remote control to switch from the normal mode to the mouse
mode. An icon appears on the screen to indicate the activation of the mouse
mode.
4. Perform the desired mouse controls on your remote control.
• To move the cursor on the screen, press   /   / 
 /  .
• To left-click, press  .
• To right-click, press  .
• To operate your display software program (on a connected PC) which responds 
to page up/down commands (like Microsoft PowerPoint), press Page Up/Page 
Down.
• To return to the normal mode, press Mouse again. 
						

							 11
Installing the Batteries
1. Open the battery cover in the 
direction shown.
2. Install batteries as indicated by the 
diagram inside the compartment.
3. Close the battery cover into position.
Caution
•
Risk of explosion if battery is replaced by an incorrect type.
•Dispose of used batteries according to the instructions.
•Make sure the plus and minus terminals are correctly aligned when loading a battery.
Note
•
Keep the batteries out of the reach of children. There is a danger of death by 
accidentally swallowing the batteries.
•Remove batteries from remote control when not using for extended periods.
•Do not dispose of the used batteries along with household waste. Dispose of used 
batteries according to local regulations.
•Danger of explosion may happen if batteries are incorrectly replaced. Replce all the 
batteries with new ones.
•Batteries should not be in or near to fire or water, keep batteries in a dark, cool and dry 
place.
•If suspect battery leakage, wipe out the leakage and then replace new batteries.
•If the leakage adheres to your body or clothes, rinse well with water immediately. 
						

							 12
Remote Control Operation
Point the remote control at the infrared remote sensor and press a button.
• Operating the projector from the
front
• Operating the projector from the 
rear
Note
•
Do not point the laser directly to the peoples eyes (especially small children). There is a 
danger of injury to the eyes.
•The remote control may not operate when there is sunlight or other strong light such as 
a fluorescent lamp shining on the remote sensor.
•Operate the remote control from a position where the remote sensor is visible.
•Do not drop the remote control or jolt it.
•Keep the remote control out of locations with excessively high temperature or humidity.
•Do not get water on the remote control or place wet objects on it.
•Do not disassemble the remote control. 
						

							 13
Connection
When connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly inserted.
Important
•
In the connections shown above, some cables may not be included with the projector 
(see Package Contents on page 2). They are commercially available from electronics 
stores.
•The connection illustrations above are for reference only. The rear connecting jacks 
available on the projector vary with each projector model.
•For detailed connection methods, see pages 14-17.
1. VGA cable (D-Sub to D-Sub) 2. VGA to DVI-A cable
3. USB cable (mini-B type to A type) 4. Audio cable
5. VGA (D-Sub) to HDTV (RCA) cable 6. S-Video cable
7. Composite Video cable 8. HDMI cable
9. USB flash drive 10. Microphone 3.5 mini jack cable
7
11234
54678
10
4
1
9