ViewSonic Projector PJD6352LS User Manual

24
Using the menus
The projector is equipped with On-Screen Display (OSD) menus for making various 
adjustments and settings.
The OSD screenshots below are for reference only, and may differ from the actual design.
Below is the overview of the OSD menu.
To use the OSD menus, please select your language first.
1. Press Menu to turn the OSD menu on.
3. Press  to highlight 
Language and press / to 
select a preferred language.
2. Use / to highlight the SYSTEM 
SETTING: BASIC menu.4. Press Exit twice* to...

25
Utilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes an option 
for setting up password security. The password can be set through the On-Screen Display 
(OSD) menu. For details of the OSD menu operation, please refer to Using the menus on 
page 24.
You will be inconvenienced if you enable the password function yet forget the password 
somehow. Do make a note of your password, and keep the note in a safe place for later recall.
Setting a...

26
Entering the password recall procedure
1. Press and hold Auto Sync on the remote control 
for 3 seconds. The projector will display a coded 
number on the screen.
2. Write down the number and turn off your 
projector.
3. Seek help from the local service center to decode 
the number. You may be required to provide 
proof of purchase documentation to verify that 
you are an authorized user of the projector.
The XXX shown in the above screenshot are numbers that vary depending on different 
projector...

27
Switching input signal
The projector can be connected to multiple devices at the same time. However, it can only 
display one full screen at a time. 
Be sure the Quick Auto Search function in the SOURCE menu is On if you want the 
projector to automatically search for the signals.
You can also manually select the desired signal by 
pressing one of the source selection keys on the 
remote control, or cycle through the available input 
signals.
1. Press Source. A source selection bar is 
displayed. 
2....

28
•Auto: Sets the projector to detect the color space setting of the input signal 
automatically.
4. Highlight HDMI Range and press / to select a suitable HDMI color range 
according to the color range setting of the output device connected.
•Enhanced: Sets the HDMI color range as 0 - 255.
•Normal: Sets the HDMI color range as 15 - 235.
•Auto: Sets the projector to detect the HDMI range of the input signal 
automatically.
This function is only available when the HDMI input port is in use.
Refer to the...

29
Fine-tuning the image clarity
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at either the 
top or bottom. It occurs when the projector is not perpendicular to the screen.
To correct this, besides adjusting the height of the projector, you will need to manually 
correct it following one of these steps.
• Using the remote control
Press /// to display the Keystone 
correction page. Press   to correct keystoning at 
the top of the image. Press   to...

30
3. Press the button that represents the corner you wish to adjust and press Enter.
4. Press / to select an adjustment method that suits your need and press Enter.
5. Press  / / /  to adjust its shape and size.
During this process, you can press Menu or Exit to go back to a previous step. A long press 
for 2 seconds on Enter will reset the settings.
Adjusting keystone or aspect ratio will reset the Corner Adj. settings.
Magnifying and searching for details
If you need to find the details on the...

31
1.Auto: Scales an image proportionally to fit the 
projectors native resolution in its horizontal 
width. This is suitable for the incoming image 
which is neither in 4:3 nor 16:9 and you want to 
make most use of the screen without altering the 
images aspect ratio.
2.4:3: Scales an image so that it is displayed in the 
center of the screen with a 4:3 aspect ratio. This 
is most suitable for 4:3 images like computer 
monitors, standard definition TV and 4:3 aspect 
DVD movies, as it displays them...

32
8.Anamorphic: Scales a 2.35:1 aspect image so 
that it fills the screen.
Optimizing the image
Selecting a picture mode
The projector is preset with several predefined picture modes so that you can choose one to 
suit your operating environment and input signal picture type.
To select an operation mode that suits your need, you can follow one of the following steps.
• Press Color Mode repeatedly until your desired mode is selected.
•Go to the PICTURE > Color Mode menu and press / to select a desired...

33 Adjusting Brightness
Go to the PICTURE > Brightness menu and press /.
The higher the value, the brighter the image. And the 
lower the setting, the darker the image. Adjust this 
control so the black areas of the image appear just as 
black and that detail in the dark areas is visible.
Adjusting Contrast
Go to the PICTURE > Contrast menu and press /.
The higher the value, the greater the contrast. Use this 
to set the peak white level after you have previously 
adjusted the Brightness setting to suit...