ViewSonic Projector PJD5134 User Manual

6
Projector exterior view
1. External control panel
(See "Projector" on page 7 for 
details.)
2. Lamp cover
3. Vent (heated air exhaust)
4. Front IR remote sensor
5. Adjuster foot
6. Focus and Zoom rings
7. Projection lens
8. RS-232 control port
9. Type B USB port
10. HDMI port
11. RGB (PC)/Component video 
(YPbPr/YCbCr) signal input 
socket-2
12. RGB (PC)/Component video 
(YPbPr/YCbCr) signal input 
socket-1
13. RGB signal output socket
14. S-Video input socket
15. Video input socket
16. Audio...

7
Controls and functions
Projector
1. Focus ring
Adjusts the focus of the projected image.
2. Zoom ring
Adjusts the size of the image.
3. Keystone/Arrow keys ( / Up,  /
Down)
Manually corrects distorted images 
resulting from an angled projection.
4. Left/Blank
Hides the screen picture.
5. POWER indicator light
Lights up or flashes when the projector is 
under operation.
POWER
Toggles the projector between standby 
mode and on.
6. SOURCE
Displays the source selection bar.
7. MENU/EXIT
Turns on the...

8
Remote control
To use the remote mouse control keys 
(Page Up, Page Down,  , and ), see 
"Using the remote mouse control" on 
page 10 for details.
1. POWER
Toggles the projector between standby 
mode and on.
2. Source selection keys (VGA/Video)
Selects an input source for display.
VGA
Selects D-Sub / Comp. 1 or D-Sub / 
Comp. 2 source for display.
Video
Selects Video source for display.
HDMI is only available on models with 
HDMI input.
3. Source
Displays the source selection bar.
4. Keystone...

9
Remote control code
The projector can be assigned to two different remote control codes, A or B. When several 
adjacent projectors are in operation at the sa me time, switching the remote control codes 
can prevent interference from other remote controls. Set the remote control code for the 
projector first before changing that for the remote control.
To switch the code for the projector, select  A or  B in the  SYSTEM SETTING: 
ADVANCED  > Remote Control Code  menu.
To switch the code for th e remote...

10
Using the remote mouse control
The capability of operating your computer with the remote control gives you more 
flexibility when delivering presentations. 
1. Connect the projector to your PC or notebook with a USB cable prior to using the 
remote control in place of your computer’s mouse. See "Connecting a computer" on 
page 16 for details.
2. Set the input signal to D-Sub / Comp. 1,D-Sub / Comp. 2 or HDMI.
The HDMI input is only available on the PJD5134/PJD5234L/PJD5533w models.
3. Press...

11
Replacing the remote control batteries
1. To open the battery cover, turn the remote control over to view its back, push on the 
finger grip on the cover and slide it in the direction of the arrow as illustrated. The 
cover will slide off.
2. Remove any existing batteries (if necessary) and install two AAA batteries observing 
the battery polarities as indicated in the base of the battery compartment. Positive (+) 
goes to positive and negative (-) goes to negative.
3. Refit the cover by aligning it...

12
Positioning your projector
Choosing a location
Your room layout or personal preference will dictate which installation location you select. 
Take into consideration the size and position of your screen, the location of a suitable power 
outlet, as well as the location and distance between the projector and the rest of your 
equipment.
Your projector is designed to be installed in one of four possible installation locations:
1. Front Table
Select this location with the projector placed near 
the floor...

13
Projection dimensions
Refer to "Dimensions" on page 60 for the center of lens dimensions of this projector before 
calculating the appropriate position.
The "screen" mentioned below refers to the projection screen usually consisting of a surface 
and a support structure
PJD5132/PJD5232L/PJD5134/PJD5234L
(a) Screen 
Size
[inch (m)]4:3 image on a 4:3 Screen 16:9 image on a 4:3 Screen
(b) Projection 
distance [m (inch)](c) Image 
height
[cm (inch)](d) Vertical 
offset
[cm (inch)] (b)...

14
PJD5533w
There is 3% tolerance among these numbers due to optical component variations. It is 
recommended that if you intend to permanently install the projector, you should physically 
test the projection size and distance using the actual projector in situ before you permanently 
install it, so as to make allowance for this projector's optical characteristics. This will help you 
determine the exact mounting position so that it best suits your installation location.
(a) Screen 
Size
[inch...

15
Connection
When connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly inserted. 
• In the connections shown below, some cables may not be included with the projector (see 
"Shipping contents" on page 5). They are commercially available from electronics stores.
• The connection illustrations below are for reference only. The rear connecting jacks...