ViewSonic Projector PJD5134 User Manual

							6
Projector exterior view
1. External control panel
(See "Projector" on page 7 for 
details.)
2. Lamp cover
3. Vent (heated air exhaust)
4. Front IR remote sensor
5. Adjuster foot
6. Focus and Zoom rings
7. Projection lens
8. RS-232 control port
9. Type B USB port
10. HDMI port
11. RGB (PC)/Component video 
(YPbPr/YCbCr) signal input 
socket-2
12. RGB (PC)/Component video 
(YPbPr/YCbCr) signal input 
socket-1
13. RGB signal output socket
14. S-Video input socket
15. Video input socket
16. Audio signal input socket
Audio signal output socket
17. Kensington anti-theft lock slot
18. AC power cord inlet
Warning
• THIS APPARATUS MUST BE EARTHED.
• When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring, 
or connect the power plug to an easily accessible socket-outlet near the unit. If a fault should 
occur during operation of the unit, operate the disconnect device to switch the power supply 
off, or disconnect the power plug.
1
2
3
4
5
6
7
Front/upper side
17
89111413151612
18
17
8109111413151612
18
Rear/lower side
PJD5134/PJD5234L/PJD5533w PJD5132/PJD5232L 
						

							7
Controls and functions
Projector
1. Focus ring
Adjusts the focus of the projected image.
2. Zoom ring
Adjusts the size of the image.
3. Keystone/Arrow keys ( / Up,  /
Down)
Manually corrects distorted images 
resulting from an angled projection.
4. Left/Blank
Hides the screen picture.
5. POWER indicator light
Lights up or flashes when the projector is 
under operation.
POWER
Toggles the projector between standby 
mode and on.
6. SOURCE
Displays the source selection bar.
7. MENU/EXIT
Turns on the On-Screen Display (OSD) 
menu. Goes back to previous OSD menu, 
exits and saves menu settings.8. Right
Activates panel key lock.
When the On-Screen Display (OSD) 
menu is activated, the #3, #4, and #8 keys 
are used as directional arrows to select the 
desired menu items and to make 
adjustments.
9. LAMP indicator light
Indicates the status of the lamp. Lights up 
or flashes when the lamp has developed a 
problem.
10. AUTO
Automatically determines the best picture 
timings for the displayed image.
11. TEMPerature indicator light
Lights up red if the projector's 
temperature becomes too high.
12. MODE/ENTER
Selects an available picture setup mode.
Enacts the selected On-Screen Display 
(OSD) menu item.
MENU
EXIT
12
3
45
63
789
1112
10
II 
						

							8
Remote control
To use the remote mouse control keys 
(Page Up, Page Down,  , and ), see 
"Using the remote mouse control" on 
page 10 for details.
1. POWER
Toggles the projector between standby 
mode and on.
2. Source selection keys (VGA/Video)
Selects an input source for display.
VGA
Selects D-Sub / Comp. 1 or D-Sub / 
Comp. 2 source for display.
Video
Selects Video source for display.
HDMI is only available on models with 
HDMI input.
3. Source
Displays the source selection bar.
4. Keystone keys ( / )
Manually corrects distorted images 
resulting from an angled projection.
5.// /
Selects the desired menu items and 
makes adjustments.6. Enter
Enacts the selected On-Screen Display 
(OSD) menu item.
7. My Button
Allows user to define a short cut key 
on the remote control, and the function 
item is selected in OSD menu.
8. Menu
Turns on the On-Screen Display 
(OSD) menu.
9.
Performs the same function as the left 
mouse button when the mouse mode is 
activated.
10.
Performs the same function as the 
right mouse button when the mouse 
mode is activated.
11. Mouse
Switches between the normal and 
mouse modes.
Page Up,Page Down, , : active 
after pressing Mouse. An icon appears 
on the screen to indicate the activation 
of the mouse mode.
1
23
5
8
9
4
6
10
12
16
13
1711
15
4
18
20
1422
23
24
25
7
21
19
II 
						

							9
Remote control code
The projector can be assigned to two different remote control codes, A or B. When several 
adjacent projectors are in operation at the sa me time, switching the remote control codes 
can prevent interference from other remote controls. Set the remote control code for the 
projector first before changing that for the remote control.
To switch the code for the projector, select  A or  B in the  SYSTEM SETTING: 
ADVANCED  > Remote Control Code  menu.
To switch the code for th e remote control, press PgUp and PgDn  buttons on the remote 
control together for 5 seconds or mo re. The initial code is set to A.
If different codes are set on the projector and re mote control, there will be no response from 
the remote control. When that happens, swit ch the code for the remote control again.
12. Magnify
Displays the zoom bar that magnifies or 
reduces the projected picture size.
13. Lock Activates or deactivates panel key lock.
14. Freeze
Freezes the projected image.
15. Pattern
Displays embedded test pattern.
16. Blank
Hides the screen picture.
17. DynamicEco™
Decreases the power consumption of the 
lamp by up to 30%.
• It takes some time to initiate this 
function. Make sure the projector has 
been turned on for more than 4 minutes.
If the projector is resumed by using the 
Smart Restart feature, this function can 
be executed immediately. 
•After 30 minutes of continuous use in 
D.Eco mode, the projector will revert to 
Normal mode for 5 minutes before 
switching back to D.Eco mode.
18. Auto SyncAutomatically determines the best picture 
timings for the displayed image. 19. Color Mode
Selects an available  picture setup mode.
20. Exit
Goes back to previous OSD menu, exits 
and saves menu settings.
21. PgUp (Page Up)/PgDn (Page Down)
Operates your display software program 
(on a connected PC) which responds to 
page up/down commands (like Microsoft 
PowerPoint) when the mouse mode is 
activated.
22. Volume keys (+, -)
Magnifies or reduces the volume level.
23.
Toggles the projector audio between on 
and off.
24. Aspect
Selects the displa y aspect ratio.
25. Timer
Displays the presentation timer settings 
menu. 
						

							10
Using the remote mouse control
The capability of operating your computer with the remote control gives you more 
flexibility when delivering presentations. 
1. Connect the projector to your PC or notebook with a USB cable prior to using the 
remote control in place of your computer’s mouse. See "Connecting a computer" on 
page 16 for details.
2. Set the input signal to D-Sub / Comp. 1,D-Sub / Comp. 2 or HDMI.
The HDMI input is only available on the PJD5134/PJD5234L/PJD5533w models.
3. Press Mouse on the remote control to switch from the normal mode to the mouse 
mode. An icon appears on the screen to indicate the activation of the mouse mode.
4. Perform the desired mouse controls on your remote control.
• To move the cursor on the screen, press  / / / . 
• To left-click, press  . 
• To right-click, press  . 
• To operate your display software program (on a connected PC) which responds to 
page up/down commands (like Microsoft PowerPoint), press PgUp/PgDn.
• To return to the normal mode, press Mouse again or other keys except for the 
mouse related multi-function keys.
Remote control effective range
The Infra-Red (IR) remote control is located on the front 
of the projector. The remote control must be held at an 
angle within 30 degrees perpendicular to the projector's 
IR remote control sensor to function correctly. The 
distance between the remote control and the sensor should 
not exceed 8 meters (~ 26 feet).
Make sure that there are no obstacles between the remote 
control and the IR sensor on the projector that might 
obstruct the infra-red beam.
Appr
ox.
15° 
						

							11
Replacing the remote control batteries
1. To open the battery cover, turn the remote control over to view its back, push on the 
finger grip on the cover and slide it in the direction of the arrow as illustrated. The 
cover will slide off.
2. Remove any existing batteries (if necessary) and install two AAA batteries observing 
the battery polarities as indicated in the base of the battery compartment. Positive (+) 
goes to positive and negative (-) goes to negative.
3. Refit the cover by aligning it with the base and sliding it back down into position. 
Stop when it clicks into place.
• Avoid leaving the remote control and batteries in an excessive heat or humid environment 
like the kitchen, bathroom, sauna, sunroom or in a closed car.
• Replace only with the same or equivalent type recommended by the battery manufacturer.
• Dispose of the used batteries according to the manufacturer's instructions and local 
environment regulations for your region.
• Never throw the batteries into a fire. There may be danger of an explosion.
• If the batteries are dead or if you will not be using the remote control for an extended 
period of time, remove the batteries to avoid damage to the remote control from possible 
battery leakage. 
						

							12
Positioning your projector
Choosing a location
Your room layout or personal preference will dictate which installation location you select. 
Take into consideration the size and position of your screen, the location of a suitable power 
outlet, as well as the location and distance between the projector and the rest of your 
equipment.
Your projector is designed to be installed in one of four possible installation locations:
1. Front Table
Select this location with the projector placed near 
the floor in front of the screen. This is the most 
common way to position the projector for quick 
setup and portability.
2. Front Ceiling
Select this location with the projector suspended 
upside-down from the ceiling in front of the 
screen.
Purchase the projector ceiling mount kit from your 
dealer to mount your projector on the ceiling.
Set Front Ceiling in the SYSTEM SETTING: 
BASIC > Projector Position menu after you turn 
the projector on.
3. Rear Ceiling
Select this location with the projector suspended 
upside-down from the ceiling behind the screen.
Note that a special rear projection screen and the 
projector ceiling mounting kit are required for this 
installation location.
Set Rear Ceiling in the SYSTEM SETTING: 
BASIC > Projector Position menu after you turn 
the projector on.
4. Rear Table
Select this location with the projector placed near 
the floor behind the screen.
Note that a special rear projection screen is 
required.
Set Rear Table in the SYSTEM SETTING: 
BASIC > Projector Position menu after you turn 
the projector on. 
						

							13
Projection dimensions
Refer to "Dimensions" on page 60 for the center of lens dimensions of this projector before 
calculating the appropriate position.
The "screen" mentioned below refers to the projection screen usually consisting of a surface 
and a support structure
PJD5132/PJD5232L/PJD5134/PJD5234L
(a) Screen 
Size
[inch (m)]4:3 image on a 4:3 Screen 16:9 image on a 4:3 Screen
(b) Projection 
distance [m (inch)](c) Image 
height
[cm (inch)](d) Vertical 
offset
[cm (inch)] (b) Projection distance 
[m (inch)](c) Image 
height
[cm (inch)](d) Vertical 
offset
[cm (inch)]
min. max. min. max.
30(0.8) 1.1 (45) 1.2 (49) 46 (18) 5 (1.8) 1.1 (45) 1.2 (49 34 (14) 10.3 (4.1)
40(1.0) 1.5 (59) 1.7 (65) 61 (24) 6 (2.4) 1.5 (59) 1.7 (65) 46 (18) 13.7 (5.4)
50(1.3) 1.9 (74) 2.1 (82)  76 (30) 8 (3.0) 1.9 (74)  2.1 (82)  57 (23) 17.1 (6.8)
60(1.5) 2.3 (89) 2.5 (98)  91 (36) 9 (3.6) 2.3 (89)  2.5 (98)  69 (27) 20.6 (8.1)
70(1.8) 2.6 (104) 2.9 (114) 107 (42) 11 (4.2) 2.6 (104) 2.9 (114) 80 (32) 24.0 (9.5)
80(2.0) 3.0 (119) 3.3 (131) 122 (48) 12 (4.8) 3.0 (119) 3.3 (131) 91 (36) 27.4 (10.8)
90(2.3) 3.4 (134) 3.7 (147) 137 (54) 14 (5.4) 3.4 (134) 3.7 (147) 103 (41) 30.9 (12.2)
100(2.5) 3.8 (149) 4.2 (163) 152 (60) 15 (6.0) 3.8 (149) 4.2 (163) 114 (45) 34.3 (13.5)
120(3.0) 4.5 (178) 5.0 (196) 183 (72) 18 (7.2) 4.5 (178) 5.0 (196) 137 (54) 41.1 (16.2)
150(3.8) 5.7 (223) 6.2 (245) 229 (90) 23 (9.0) 5.7 (223) 6.2 (245) 171 (68) 51.4 (20.3)
200(5.1) 7.5 (297) 8.3 (327) 305 (120) 30 (12.0) 7.5 (297) 8.3 (327) 229 (90) 68.6 (27.0)
250(6.4) 9.4 (371) 10.4 (409) 381 (150) 38 (15.0) 9.4 (371) 10.4 (409) 286 (113) 85.7 (33.8)
300(7.6) 11.3 (446) 12.5 (490) 457 (180) 46 (18.0) 11.3 (446) 12.5 (490) 343 (135) 102.9 (40.5)
(a)
(c)
(b)(e)
(f)
(d)
(a)
(d)
(b)(e)
(f)
(c)
(a)
(d)
(c)(b)
(e)(f)
(a)
(c)(b)
(e)(f)
(d)
(f): Center of lens (e): Screen
• 4:3 image on a 4:3 screen
• 16:9 image on a 4:3 screen 
						

							14
PJD5533w
There is 3% tolerance among these numbers due to optical component variations. It is 
recommended that if you intend to permanently install the projector, you should physically 
test the projection size and distance using the actual projector in situ before you permanently 
install it, so as to make allowance for this projector's optical characteristics. This will help you 
determine the exact mounting position so that it best suits your installation location.
(a) Screen 
Size
[inch (m)]16:10 image on a 16:10 Screen 16:10 image on a 4:3 Screen
(b) Projection distance 
[m (inch)](c) Image 
height
[cm (inch)](d) Vertical 
offset
[cm (inch)] (b) Projection distance 
[m (inch)](c) Image 
height
[cm (inch)](d) Vertical 
offset
[cm (inch)]
min. max. min. max.
30(0.8) 0.97 (38) 1.06 (42) 40 (16) 0 (0.0) 0.91 (36) 1.00 (40) 38 (15) 3.8 (1.5)
40(1.0) 1.29 (51) 1.42 (56) 54 (21) 0 (0.0) 1.22 (48) 1.34 (53) 51 (20) 5.1 (2.0)
50(1.3) 1.61 (64) 1.77 (70) 67 (26) 0 (0.0) 1.52 (60) 1.67 (66) 64 (25) 6.4 (2.5)
60(1.5) 1.94 (76) 2.13 (84) 81 (32) 0 (0.0) 1.83 (72) 2.01 (79) 76 (30) 7.6 (3.0)
70(1.8) 2.26 (89) 2.48 (98) 94 (37) 0 (0.0) 2.13 (84) 2.34 (92) 89 (35) 8.9 (3.5)
80(2.0) 2.58 (102) 2.84 (112) 108 (42) 0 (0.0) 2.43 (96) 2.68 (105) 102 (40) 10.2 (4.0)
90(2.3) 2.90 (114) 3.19 (126) 121 (48) 0 (0.0) 2.74 (108) 3.01 (119) 114 (45) 11.4 (4.5)
100(2.5) 3.23 (127) 3.55 (140) 135 (53) 0 (0.0) 3.04 (120) 3.35 (132) 127 (50) 12.7 (5.0)
120(3.0) 3.87 (152) 4.26 (168) 162 (64) 0 (0.0) 3.65 (144) 4.02 (158) 152 (60) 15.2 (6.0)
150(3.8) 4.84 (191) 5.32 (210) 202 (79) 0 (0.0) 4.56 (180) 5.02 (198) 191 (75) 19.1 (7.5)
200(5.1) 6.45 (254) 7.10 (279) 269 (106) 0 (0.0) 6.09 (240) 6.70 (264) 254 (100) 25.4 (10.0)
250(6.4) 8.06 (318) 8.87 (349) 337 (132) 0 (0.0) 7.61 (300) 8.37 (329) 318 (125) 31.8 (12.5)
300(7.6) 9.68 (381) 10.65 (419) 404 (159) 0 (0.0) 9.13 (359) 10.04 (395) 381 (150) 38.1 (15.0)
(a)
(c)
(b)(e)
(f)
(d)
(a)
(c)(b)
(e)(f)
(d)
(a)
(c)
(b)(e)
(f)
(d)
(f): Center of lens (e): Screen
• 16:10 image on a 16:10 screen
• 16:10 image on a 4:3 screen
(a)
(d)
(c)(b)
(e)(f) 
						

							15
Connection
When connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly inserted. 
• In the connections shown below, some cables may not be included with the projector (see 
"Shipping contents" on page 5). They are commercially available from electronics stores.
• The connection illustrations below are for reference only. The rear connecting jacks 
available on the projector vary with each projector model.
• For detailed connection methods, see pages 16-19.
1. VGA cable
2. VGA to DVI-A cable
3. USB cable
4. Component Video to VGA (D-Sub) 
adapter cable5. S-Video cable
6. Video cable
7. Audio cable
8. HDMI cable
5748
1
63127
7
Notebook or desktop computer
Speakers orA/V device
Monitor
(DVI) (VGA)
PJD5134/
PJD5234L/
PJD5533w
PJD5132/
PJD5232L