ViewSonic Projector PJD5134 User Manual

							PJD5132/PJD5232L/PJD5134/
PJD5234L/PJD5533w
DLP Projector
User Guide
IMPORTANT: Please read this User Guide to obtain important information on installing 
and using your product in a safe manner, as well as registering your product for 
future service. Warranty information contained in this User Guide will describe your 
limited coverage from ViewSonic Corporation, which is also found on our web site at  
http://www.viewsonic.com in English, or in specific languages using the Regional 
selection box in the upper right corner of our website. “Antes de operar su equ\
ipo lea cu 
idadosamente las instrucciones en este manual”
Model No. VS14926/VS14929/VS14928/VS14930/VS14117 
						

							i
FCC Statement
This device complies with part 15 of FCC Rules. Operation is subject to \
the following two 
conditions: (1) this device may not cause harmful interference, and (\
2) this device must accept 
any interference received, including interference that may cause undesir\
ed operation.
This equipment has been tested and found to comply with the limits for a\
 Class B digital 
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential installation. This equipment generates, 
uses, and can radiate radio frequency energy, and if not installed and used in accordance with 
the instructions, may cause harmful interference to radio communications\
. However, there is 
no guarantee that interference will not occur in a particular installati\
on. If this equipment does 
cause harmful interference to radio or television reception, which can b\
e determined by turning 
the equipment off and on, the user is encouraged to try to correct the interference by o\
ne or 
more of the following measures:
 
yReorient or relocate the receiving antenna.
 
yIncrease the separation between the equipment and receiver.
 
yConnect the equipment into an outlet on a circuit different from that to which the 
receiver is connected.
 
yConsult the dealer or an experienced radio/TV technician for help.
Warning: You are cautioned that changes or modifications not expressly approved by the 
party responsible for compliance could void your authority to operate th\
e equipment.
For Canada
CAN ICES-3(B)/NMB-3(B)
CE Conformity for European Countries
The device complies with the EMC Directive 2004/108/EC and Low Voltage 
Directive 2006/95/EC.
Following information is only for EU-member states:
The mark is in compliance with the Waste Electrical and Electronic Equipment Directive 
2002/96/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment including any spent 
or discarded batteries or accumulators as unsorted municipal waste, but \
use the return 
and collection systems available. 
If the batteries, accumulators and button cells included with this equip\
ment, display 
the chemical symbol Hg, Cd, or Pb, then it means that the battery has a \
heavy metal 
content of more than 0.0005% Mercury or more than, 0.002% Cadmium, or mo\
re than 
0.004% Lead.
Compliance Information
   
						

							ii
Important Safety Instructions
1. Read these instructions.
2.  Keep these instructions.
3.  Heed all warnings.
4.  Follow all instructions.
5.  Do not use this unit near water.
6.  Clean with a soft, dry cloth.
7.  Do not block any ventilation openings. Install the unit in accordance wi\
th the   
manufacturer’s instructions.
8.  Do not install near any heat sources such as radiators, heat registers, \
stoves, or other 
devices (including amplifiers) that produce heat.
9.  Do not defeat the safety purpose of the polarized or grounding-type plug\
. A polarized plug 
has two blades with one wider than the other. A grounding type plug has two blades and a 
third grounding prong. The wide blade and the third prong are provided for your safety. If 
the provided plug does not fit into your outlet, consult an electrician for replacement of the 
obsolete outlet.
10.  Protect the power cord from being walked on or pinched particularly at plugs. Convenience 
receptacles and the point where they exit from the unit. Be sure that th\
e power outlet is 
located near the unit so that it is easily accessible.
11.  Only use attachments/accessories specified by the manufacturer.
12.  Use only with the cart, stand, tripod, bracket, or table specified by the   
manufacturer, or sold with the unit. When a cart is used, use caution when moving 
the cart/unit combination to avoid injury from tipping over.
13.  Unplug this unit when unused for long periods of time.
14.  Refer all servicing to qualified service personnel. Servicing is required when the unit has 
been damaged in any way, such as: if the power-supply cord or plug is damaged, if liquid 
is spilled onto or objects fall into the unit, if the unit is exposed to\
 rain or moisture, or if the 
unit does not operate normally or has been dropped.
   
						

							iii
Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with Direc\
tive 2011/65/
EU of the European Parliament and the Council on restriction of the use \
of certain hazardous 
substances in electrical and electronic equipment (RoHS2 Directive) an\
d is deemed to comply 
with the maximum concentration values issued by the European Technical Adaptation Commit-
tee (TAC) as shown below:
Substance Proposed Maximum
Concentration Actual Concentration
Lead (Pb) 0.1%< 0.1%
Mercury (Hg) 0.1%< 0.1%
Cadmium (Cd) 0.01%< 0.01%
Hexavalent Chromium (Cr 6+
) 0.1%< 0.1%
Polybrominated biphenyls (PBB) 0.1%< 0.1%
Polybrominated diphenyl ethers (PBDE) 0.1%< 0.1%
Certain components of products as stated above are exempted under the Annex III of the 
RoHS2 Directives as noted below:
Examples of exempted components are:
1. Mercury in cold cathode fluorescent lamps and external electrode fluorescent lamps 
(CCFL and EEFL) for special purposes not exceeding (per lamp):
(1) Short length (≦500 mm): maximum 3.5 mg per lamp.
(2) Medium length ( ＞500 mm and ≦1,500 mm): maximum 5 mg per lamp.
(3) Long length ( ＞1,500 mm): maximum 13 mg per lamp.
2.  Lead in glass of cathode ray tubes.
3.  Lead in glass of fluorescent tubes not exceeding 0.2% by weight.
4.  Lead as an alloying element in aluminium containing up to 0.4% lead by w\
eight.
5.  Copper alloy containing up to 4% lead by weight.
6.  Lead in high melting temperature type solders (i.e. lead-based alloys c\
ontaining 85% by 
weight or more lead).
7.  Electrical and electronic components containing lead in a glass or ceram\
ic other than   
dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a \
glass or ceramic 
matrix compound.
   
						

							iv
Copyright Information
Copyright © ViewSonic®
 Corporation, 2013. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft 
Corporation in the United States and other countries.
ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks 
of ViewSonic Corporation.
VESA is a registered trademark of the Video Electronics Standards Association. DPMS and 
DDC are trademarks of VESA.
PS/2, VGA and XGA are registered trademarks of International Business Machines Corporation.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial erro\
rs or omis -
sions contained herein; nor for incidental or consequential damages resu\
lting from furnishing 
this material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves the right to 
change product specifications without notice. Information in this document may change without 
notice.
No part of this document may be copied, reproduced, or transmitted by an\
y means, for any 
purpose without prior written permission from ViewSonic Corporation.
Product Registration
To meet your future needs, and to receive any additional product informat\
ion as it becomes 
available, please register your product on the Internet at: www.viewsonic.com. The ViewSonic ®
 
Wizard CD-ROM also provides an opportunity for you to print the registra\
tion form, which you 
may mail or fax to ViewSonic.
For Your Records
Product Name: PJD5132/PJD5232L/PJD5134/PJD5234L/PJD5533w
ViewSonic DLP Projector
Model Number: VS14926/VS14929/VS14928/VS14930/VS14117
Document Number: PJD5132/PJD5232L/PJD5134/PJD5234L/PJD5533w_
UG_ENG Rev. 1B 05-07-13
Serial Number: ___________________________________________
Purchase Date: ___________________________________________
Product disposal at end of product life
The lamp in this product contains mercury which can be dangerous to you and the environment. 
Please use care and dispose of in accordance with local, state or federa\
l laws.
ViewSonic respects the environment and is committed to working and living\
 green. Thank you 
for being part of Smarter, Greener Computing. Please visit ViewSonic website to learn more.
USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/
Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx
   
						

							1
Table of contents
Important safety 
instructions .......................2
Introduction ......................4
Projector features ................................. 4
Shipping contents ................................. 5
Projector exterior view ......................... 6
Controls and functions ......................... 7
Positioning your 
projector..........................12
Choosing a location............................ 12
Projection dimensions ........................ 13
Connection ......................15
Connecting a computer or monitor .... 16
Connecting Video source devices ...... 17
Operation ........................20
Starting up the projector..................... 20
Using the menus................................. 21
Utilizing the password function ......... 22
Switching input signal........................ 25
Adjusting the projected image ........... 26
Magnifying and searching for details. 27
Selecting the aspect ratio ................... 28
Optimizing the image......................... 31
Setting the presentation timer ............ 35
Hiding the image ................................ 36
Locking control keys.......................... 36
Freezing the image ............................. 36
Operating in a high altitude 
environment ....................................... 36
Using the CEC function ..................... 37
Using the 3D functions ...................... 37Using the projector in standby mode . 38
Shutting down the projector .............. 39
Menu operation .................................. 40
Maintenance ...................50
Care of the projector .......................... 50
Lamp information .............................. 51
Troubleshooting .............57
Specifications ..................58
Projector specifications...................... 58
Dimensions ........................................ 60
Ceiling mount installation ................. 60
Timing chart ...................................... 61
Copyright information...63
Appendix .........................64
IR control table .................................. 64
RS232 command table ....................... 66 
						

							2
Important safety instructions
Your projector is designed and tested to meet the latest standards for safety of information 
technology equipment. However, to ensure safe use of this product, it is important that you 
follow the instructions mentioned in this manual and marked on the product. 
Safety Instructions
1.Please read this manual before you operate your projector. Save it for future 
reference.
2.Do not look straight at the projector lens during operation. The intense light beam 
may damage your eyes.
3.Refer servicing to qualified service personnel.
4.Always open the lens shutter or remove the lens cap when the projector lamp is 
on.
5. In some countries, the line voltage is NOT stable. This projector is designed to operate 
safely within a mains voltage between 100 to 240 volts AC, but could fail if power 
cuts or surges of ±10 volts occur. In areas where the mains voltage may fluctuate 
or cut out, it is recommended that you connect your projector through a power 
stabilizer, surge protector or uninterruptible power supply (UPS). 
6. Do not block the projection lens with any objects when the projector is under 
operation as this could cause the objects to become heated and deformed or even 
cause a fire. To temporarily turn off the lamp, press BLANK on the projector or 
remote control.
7. The lamp becomes extremely hot during operation. Allow the projector to cool for 
approximately 45 minutes prior to removing the lamp assembly for replacement. 
8. Do not operate lamps beyond the rated lamp life. Excessive operation of lamps 
beyond the rated life could cause them to break on rare occasions. 
9. Never replace the lamp assembly or any electronic components unless the projector is 
unplugged. 
10. Do not place this product on an unstable cart, stand, or table. The product may fall, 
sustaining serious damage. 
11. Do not attempt to disassemble this projector. There are dangerous high voltages inside 
which may cause death if you should come into contact with live parts. The only user 
serviceable part is the lamp which has its own removable cover.
Under no circumstances should you ever undo or remove any other covers. Refer 
servicing only to suitably qualified professional service personnel.
12. Do not place this projector in any of the following environments. 
-  Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls 
and free flow of air around the projector.
-  Locations where temperatures may become excessively high, such as the inside of a 
car with all windows rolled up.
-  Locations where excessive humidity, dust, or cigarette smoke may contaminate optical 
components, shortening the projector's life span and darkening the picture.
-  Locations near fire alarms
-  Locations with an ambient temperature above 40°C / 104°F
-  Locations where the altitudes are higher than 3000 m (10000 feet). 
						

							3
13. Do not block the ventilation holes. If the ventilation holes are seriously obstructed, 
overheating inside the projector may result in a fire.
-  Do not place this projector on a blanket, bedding or any other soft surface. 
-  Do not cover this projector with a cloth or any other item. 
-  Do not place inflammables near the projector.   
14. Always place the projector on a level, horizontal surface during operation.
-  Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of 
more than 15 degrees front to back. Using the projector when it is not fully horizontal 
may cause a malfunction of, or damage to, the lamp.
15. Do not stand the projector on end vertically. Doing so may cause the projector to fall 
over, causing injury or resulting in damage to the projector.
16. Do not step on the projector or place any objects upon it. Besides probable physical 
damage to the projector, doing so may result in accidents and possible injury.
17. Do not place liquids near or on the projector. Liquids spilled into the projector may 
cause it to fail. If the projector does become wet, disconnect it from the power 
supply's wall socket and call your local service center to have the projector serviced.
18. This product is capable of displaying inverted pictures for ceiling mount installation. 
Use only qualified ceiling mount kit for mounting the projector and ensure it is 
securely installed. 
19. When the projector is under operation, you may sense some heated air and odor from 
its ventilation grill. It is a normal phenomenon and not a product defect.
20. Do not use the Security bar for transporting or installation. It should be used with a 
commercially available theft prevention cable.
Safety instructions for ceiling mounting of the 
projector
We want you to have a pleasant experience using your projector, so we need to bring this 
safety matter to your attention to prevent damage to person and property.
If you intend to mount your projector on the ceiling, we strongly recommend that you use a 
proper fitting projector ceiling mount kit and that you ensure it is securely and safely 
installed.
If you use an inappropriate projector ceiling mount kit, there is a safety risk that the 
projector may fall from the ceiling due to an improper attachment through the use of the 
wrong gauge or length screws.
You can purchase a projector ceiling mount kit from the place you purchased your projector. 
We recommends that you also purchase a separate Kensington lock compatible security 
cable and attach it securely to both the Kensington lock slot on the projector and the base of 
the ceiling mount bracket. This will perform the secondary role of restraining the projector 
should its attachment to the mounting bracket become loose.  
						

							4
Introduction
Projector features
The projector integrates high-performance optical engine projection and a user-friendly 
design to deliver high reliability and ease of use.
The projector offers the following features.
• Dynamic PC and Dynamic Movie functions adjusting the power consumption of the 
lamp according to the brightness of the image being projected
• DynamicEco Timer function decreasing the power consumption of the lamp by up to 
30% when no input signal can be detected for a set period of time.
• Presentation timer for better control of time during presentations
• Supports 3D display
• Color Management allowing color adjustments to your liking
• Less than 0.5W power consumption when power saving mode is turned on
• Screen Color correction allowing projection on surfaces of several predefined colors
• Quick auto search speeding up the signal detecting process
• Color and Reference modes providing choices for different projection purposes
• Selectable quick power off function
• One-key auto-adjustment to display the best picture quality
• Digital keystone correction to correct distorted images
• Adjustable color management control for data/video display
• Ability to display 1.07 billion colors
• Multi-language On-Screen Display (OSD) menus
• Switchable normal and economic modes to reduce the power consumption
• Component HDTV compatibility (YP
bPr)
• HDMI CEC (Consumer Electronics Control) function allows synchronized power ON/
OFF operation between the projector and a CEC-compatible device connected to the 
HDMI input of the projector (PJD5134/PJD5234L/PJD5533w models only)
• The apparent brightness of the projected image will vary depending on the ambient 
lighting conditions, selected input signal contrast/brightness settings, and is directly 
proportional to projection distance.
• The lamp brightness will decline over time and may vary within the lamp manufacturers 
specifications. This is normal and expected behavior. 
						

							5
Shipping contents
Carefully unpack and verify that you have all of the items shown below. If any of these 
items are missing, please contact your place of purchase.
Standard accessories
The supplied accessories will be suitable for your region, and may differ from those 
illustrated.
Optional accessories
1. Replacement lamp
2. Soft carry case
3. VGA-Component adapterProjector Power Cord VGA Cable
Multi-language user 
manual DVDQuick Start Guide Remote Control & Batteries