ViewSonic Projector PJD5132 User Manual

							46
Function Description
Quick Auto 
SearchSee "Switching input signal" on page 25 for details.
HDMI FormatSee "Changing HDMI input settings" on page 25 for details.HDMI Range
DynamicEco 
Timer
Allows the projector to decrease the power consumption automatically 
if no input signal is detected after a set period of time.
It takes some time to initiate this function. Make sure the 
projector has been turned on for more than 4 minutes.
Smart
Restart
Selecting On enables you to restart the projector immediately within 
150 seconds after turning it off. After 150 seconds, if the projector is 
not turned on again, it will directly enter the standby mode.
•It takes some time to initiate this function. Make sure the 
projector has been turned on for more than 4 minutes.
If the projector is resumed by using the Smart Restart feature, 
this function can be executed immediately. 
•When On is selected, the Quick Power Off function will be 
automatically set to “On”.
Pattern
The projector can display several test patterns. It helps you adjust the 
image size and focus and check that the projected image is free from 
distortion.
Selecting User displays the picture you saved as Screen Capture.
My ButtonSets a hotkey on remote control.
3. SOURCE menu 
						

							47
Function Description
LanguageSets the language for the On-Screen Display (OSD) menus. See 
"Using the menus" on page 21 for details.
Projector 
PositionThe projector can be installed on a ceiling or behind a screen, or with 
one or more mirrors. See "Choosing a location" on page 12 for 
details.
Auto Power 
OffAllows the projector to turn off automatically if no input signal is 
detected after a set period of time. See "Setting Auto Power Off" on 
page 51 for details.
Timer
Blank Timer
Sets the image blank time when the Blank feature is activated, once 
elapsed the image will return to the screen. See "Hiding the image" 
on page 36 for details.
Sleep Timer
Allows the projector to turn off automatically after a set period of 
time if the incoming signal is present or not.
Panel Key 
LockDisables or enables all panel key functions except POWER on the 
projector and keys on the remote control. See "Locking control keys" 
on page 36 for details.
Splash ScreenAllows you to select which logo screen will be displayed during 
projector start-up.
MessageSelecting On displays the current information on the screen when the 
projector is detecting or searching for a signal.
Standby 
SettingsSee "Using the projector in standby mode" on page 38 for details.
CECSee "Using the CEC function" on page 37 for details.
4. SYSTEM SETTING: BASIC menu
II 
						

							48
Function Description
High Altitude 
ModeA mode for operation in high altitude areas. See "Operating in a high 
altitude environment" on page 36 for details.
DCR
Enables or disables the DCR (Dynamic Contrast Ratio) function. 
SelectingOn enables the function and the projector will 
automatically switch the lamp mode between normal and economic 
modes according to the input image detected.
This function is only available when a PC source is in use.
After enabling DCR, frequent lamp mode switching may shorten 
lamp life and noise level will vary during operation.
Audio Settings
The sound adjustments made as below will have an effect on the 
projector speaker. Be sure you have made a correct connection to the 
projector audio input/output jacks. See "Connection" on page 15 for 
more details.
Mute
Mutes the sound received from AUDIO IN.
Volume
Adjusts the sound level received from AUDIO IN.
Menu Settings
Menu Display Time
Sets the length of time the OSD will remain active after your last key 
press. The range is from 5 to 30 seconds in 5-second increments.
Menu Position
Sets the On-Screen Display (OSD) menu position.
Closed 
Caption
Closed Caption Enable
Activates the function by selecting On when the selected input signal 
carries closed captions.
• Captions: An on-screen display of the dialogue, narration, and 
sound effects of TV programs and videos that are closed 
captioned (usually marked as "CC" in TV listings).
This function is only available when a Composite video or S-
Video input signal is selected and its system format is NTSC.
Caption Version
Selects a preferred closed captioning mode. To view captions, select 
CC1, CC2, CC3, or CC4 (CC1 displays captions in the primary 
language in your area).
Lamp Settings
Lamp Mode 
See"Setting Lamp Mode as Economic" on page 51 for details.
Reset Lamp Timer
See"Resetting the lamp timer" on page 55 for details.
Equivalent Lamp Hour
See"Getting to know the lamp hour" on page 51 for details on how 
the total lamp hour is calculated.
5. SYSTEM SETTING: ADVANCED menu 
						

							49
Function Description
Presentation 
TimerReminds the presenter to finish the presentation within a certain time 
frame. See "Setting the presentation timer" on page 35 for details.
Security
SettingsSee"Utilizing the password function" on page 22 for details.
Remote
Control CodeSee"Remote control code" on page 9 for details.
Reset Settings
Reset All Settings
Returns all settings to the factory preset values.
The following settings will still remain: Keystone, Language, 
Projector Position, High Altitude Mode, Security Settings, 
Remote Control Code.
Reset Color Settings
Returns all color settings to the factory preset values.
Current
System Status
Source
Shows the current signal source.
Color Mode
Shows the selected mode in the PICTURE menu.
Resolution
Shows the native resolution of the input signal.
Color System
Shows input system format, NTSC, PAL, SECAM, or RGB.
Equivalent Lamp Hour
Displays the number of hours the lamp has been used.
5. SYSTEM SETTING: ADVANCED menu
6. INFORMATION menu 
						

							50
Maintenance
Care of the projector
Your projector needs little maintenance. The only thing you need to do on a regular basis is 
to keep the lens clean.
Never remove any parts of the projector except the lamp. Contact your dealer if other parts 
need replacing.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface.
• Use a canister of compressed air to remove dust.
• If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens 
cleaner and gently wipe the lens surface.
CAUTION
Never rub the lens with abrasive materials.
Cleaning the projector case
Before you clean the case, turn the projector off using the proper shutdown procedure as 
described in "Shutting down the projector" on page 39 and unplug the power cord.
• To remove dirt or dust, wipe the case with a soft, lint-free cloth.
• To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH 
detergent. Then wipe the case.
CAUTION
Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the 
case.
Storing the projector
If you need to store the projector for an extended time, please follow the instructions below:
• Make sure the temperature and humidity of the storage area are within the 
recommended range for the projector. Please refer to"Specifications" on page 58 or 
consult your dealer about the range.
• Retract the adjuster feet.
• Remove the battery from the remote control.
• Pack the projector in its original packing or equivalent.
Transporting the projector
It is recommended that you ship the projector with its original packing or equivalent. 
						

							51
Lamp information
Getting to know the lamp hour
When the projector is in operation, the duration (in hours) of lamp usage is automatically 
calculated by the built-in timer.
To obtain the lamp hour information:
1. Press MENU/EXIT on the projector or Menu on the remote control and then press 
/  until the SYSTEM SETTING: ADVANCED menu is highlighted.
2. Press  to highlight Lamp Settings and press MODE/ENTER on the projector or 
ENTER on the remote control. The Lamp Settings page is displayed.
3. You will see the Equivalent lamp hour information on the menu.
4. To leave the menu, press MENU/EXIT on the projector or Exit on the remote 
control.
You can also get the lamp hour information on the INFORMATION menu.
Extending lamp life
The projection lamp is a consumable item. To keep the lamp life as long as possible, you 
can do the following settings via the OSD menu.
Setting Lamp Mode as Economic
UsingEconomic mode reduces system noise and power consumption by 20%. If the 
Economic mode is selected, the light output will be reduced and result in darker projected 
pictures.
Setting the projector in Economic mode also extends the lamp operation life. To set 
Economic mode, go into the SYSTEM SETTING: ADVANCED > Lamp Settings > 
Lamp Mode menu and press  / .
Setting Auto Power Off
This function allows the projector to turn off automatically if no input source is detected 
after a set period of time to prevent unnecessary waste of lamp life.
To  s e t  Auto Power Off, go into the SYSTEM SETTING: BASIC > Auto Power Off
menu and press  / . If the preset time lengths are not suitable for your presentation, 
selectDisable. The projector will not automatically shut down in a certain time period. 
						

							52
Timing of replacing the lamp
When the LAMP indicator light lights up red or a message appears suggesting it is time to 
replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a 
malfunction in the projector and in some instances the lamp may explode.
CAUTION
The LAMP indicator light and TEMPerature indicator light will light up if the lamp becomes too 
hot. Turn the power off and let the projector cool for 45 minutes. If the LAMP or TEMP indicator 
still lights up after turning the power back on, please contact your dealer. See "Indicators" on 
page 56 for details.
The following lamp warning displays will remind you to change the lamp.
StatusMessage
Install a new lamp for optimal performance. If the 
projector is normally run with Economic selected 
(See "Setting Lamp Mode as Economic" on page 
51), you may continue to operate the projector 
until the next hour lamp warning appears.
A new lamp should be fitted to avoid the 
inconvenience when the projector runs out of lamp 
time.
It is strongly recommended that you replace the 
lamp at this age. The lamp is a consumable item. 
The lamp brightness diminishes with use. This is 
normal lamp behavior. You can replace the lamp 
whenever you notice that the brightness level has 
significantly diminished. If the lamp is not 
replaced beforehand, it must be replaced when 
you see this message.
The lamp MUST be replaced before the projector 
will operate normally.
OK
Order Replacement Lamp
Lamp > ____ Hours
Notice
OK
Replace Lamp Soon 
Lamp > ____ Hours
Notice
OK
Replace Lamp Now 
Lamp > ____ Hours
Lamp usage time exceeded
Notice
OK
Lamp usage time exceeded
Replace lamp (refer to User Manual)
Then reset lamp timer
Notice 
						

							53
Replacing the lamp
To prepare a new lamp, contact your dealer and tell the lamp type number.
Type number: RLC-078 (PJD5132/PJD5232L/PJD5134/PJD5234L) 
Type number: RLC-085 (PJD5533w)
WARNING
Hg - Lamp contains mercury. Manage in accordance with local disposal 
laws. See www.lamprecycle.org
• Be careful of broken glass when replacing the lamp.
• Please wear eye protection and gloves when performing overhead installation.
• To reduce the risk of electrical shock, always turn the projector off and disconnect the 
power cord before changing the lamp.
• To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes 
before replacing the lamp.
• To reduce the risk of injuries to fingers and damage to internal components, use caution 
when removing lamp glass that has shattered into sharp pieces. Before replacing the 
lamp, clean the lamp compartment and dispose of cleaning materials. Be careful of sharp 
edges in the lamp compartment. Wash hands after lamp replacement.
• Only ViewSonic certified lamps are tested with this projector. Use of other lamps may 
cause electrical shock and fire.
1. Turn the power off and disconnect the 
projector from the wall socket. If the lamp 
is hot, avoid burns by waiting for 
approximately 45 minutes until the lamp 
has cooled.
2. Loosen the screws that secure the lamp 
cover on the both sides of the projector until 
the lamp cover loosens.
3. Remove the lamp cover from the projector.
WARNING
• Do not turn the power on with the lamp cover 
removed.
• Do not insert your fingers between the lamp 
and the projector. The sharp edges inside the 
projector may cause injuries.
Remove and dispose of the lamp protection film. 
						

							54
4. Loosen the screw that secures the lamp.
5. Disconnect the lamp’s wire connector from 
the projector, and then lift the handle so that 
it stands up. Use the handle to slowly pull 
the lamp out of the projector.
CAUTION
• Pulling it too quickly may cause the lamp to 
break and scatter broken glass in the projector.
• Do not place the lamp in locations where water 
might splash on it, children can reach it, or 
near flammable materials.
• Do not insert your hands into the projector 
after the lamp is removed. If you touch the 
optical components inside, it could cause color 
unevenness and distortion of the projected 
images.
6. Insert the new lamp into the lamp 
compartment and make sure it fits in the 
projector. Connect the new lamp’s wire 
connector to the projector.
7. Tighten the screw that secures the lamp.
CAUTION
• Loose screw may cause a bad connection, 
which could result in malfunction.
• Do not over tighten the screw.
8. Ensure the handle is fully laid flat and 
locked in place.
1 23 
						

							55
12. Restart the projector.
CAUTION
Do not turn the power on with the lamp cover removed.
Resetting the lamp timer
13. After the startup logo, open the On-Screen 
Display (OSD) menu.
14. Go to the SYSTEM SETTING: 
ADVANCED > Lamp Settings menu. Press 
MODE/ENTER on the projector or ENTER
on the remote control. The Lamp Settings
page is displayed. 
15. Press  to highlight Reset lamp timer and 
pressMODE/ENTER on the projector or 
ENTER on the remote control. A warning 
message is displayed asking if you want to 
reset the lamp timer. 
16. Highlight Reset and press MODE/ENTER
on the projector or ENTER on the remote 
control. The lamp time will be reset to '0'.
CAUTION
Do not reset if the lamp is not new or replaced as this 
could cause damage. 
9. Place the lamp protection film supplied 
with the new lamp on the lamp 
compartment.
10. Replace the lamp cover on the projector.
11. Tighten the screws that secure the lamp 
cover.
CAUTION
• Loose screw may cause a bad connection, 
which could result in malfunction.
• Do not over tighten the screws.
Reset Lamp Timer
Reset
Cancel
Notice