ViewSonic Projector PJD5132 User Manual

							26
•YUV: Sets the color space as YUV.
•Auto: Sets the projector to detect the color space setting of input signal 
automatically.
3. Press  to highlight HDMI Range and press  /  to select a suitable HDMI color 
range according to the color range setting of the output device connected.
•Enhanced: Sets the HDMI color range as 0 - 255.
•Normal: Sets the HDMI color range as 15 - 235.
• This function is only available when the HDMI input port is in use.
• Refer to the documentation of the device for information on the color space setting.
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with an adjuster foot. It 
changes the image height and vertical projection 
angle. Screw the adjuster foot to fine tune the 
angle until the image is positioned where you 
want it.
If the projector is not placed on a flat surface or 
the screen and the projector are not perpendicular 
to each other, the projected image becomes 
trapezoidal. To correct this situation, see 
"Correcting keystone" on page 27 for details.
Do not look into the lens while the lamp is on. The strong light from the lamp may cause 
damage to your eyes.
Auto-adjusting the image
In some cases, you may need to optimize the picture quality. To do this, press AUTO on the 
projector or Auto Sync on the remote control. Within 3 seconds, the built-in Intelligent 
Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the 
best picture quality.
The current source information will be displayed in the upper left corner of the screen for 3 
seconds.
• The screen will be blank while AUTO is functioning.
• This function is only available when PC signal (analog RGB) is selected.
Fine-tuning the image clarity
1. Adjust the projected image to the size 
that you need using the zoom ring.2. If necessary, sharpen the image by 
rotating the focus ring. 
						

							27
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at either the 
top or bottom. It occurs when the projector is not perpendicular to the screen.
To correct this, besides adjusting the height of the projector, you will need to manually 
correct it following one of these steps.
• Using the remote control
Press  /  on the projector or remote control to 
display the Keystone correction page. Press   to 
correct keystoning at the top of the image. Press   
to correct keystoning at the bottom of the image.
• Using the OSD menu
1. Press MENU/EXIT on the projector or Menu on the remote control and then press 
/  until the 
DISPLAY menu is highlighted.
2. Press  to highlight Keystone and press MODE/ENTER on the projector or Enter
on the remote control. The Keystone correction page is displayed.
3. Press   to correct keystoning at the top of the image or press   to correct 
keystoning at the bottom of the image.
Magnifying and searching for details
If you need to find the details on the projected picture, magnify the picture. Use the 
direction arrow keys for navigating the picture.
• Using the remote control
1. Press Magnify on the remote control to display the Zoom bar.
2. Press   repeatedly to magnify the picture to a desired size.
3. To navigate the picture, press MODE/ENTER on the projector or Enter on the 
remote control to switch to the paning mode and press the directional arrows 
( , , , ) to navigate the picture.
4. To reduce size of the picture, press MODE/ENTER on the projector or Enter on the 
remote control to switch back to the zoom in/out functionality, and press AUTO/Auto
Sync to restore the picture to its original size. You can also press   repeatedly until 
it is restored to the original size.
• Using the OSD menu
1. Press MENU/EXIT on the projector or Menu on the remote control and then press 
/  until the DISPLAY menu is highlighted.
2. Press to highlight Zoom and press MODE/ENTER on the projector or Enter on 
the remote control. The Zoom bar is displayed.
3. Repeat steps 2-4 in the section of Using the remote control above.
The picture can only be navigated after the picture is magnified. You can further magnify the 
picture while searching for details.
Press/Press / 
						

							28
Selecting the aspect ratio
The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and 
computers are in 4:3 ratio, and digital TV and DVDs are usually in 16:9 ratio.
With the advent of digital signal processing, digital display devices like this projector can 
dynamically stretch and scale the image output to a different aspect than that of the image 
input signal.
To change the projected image ratio (no matter what aspect the source is):
• Using the remote control
1. Press Aspect to show the current setting.
2. Press Aspect repeatedly to select an aspect ratio to suit the format of the video signal 
and your display requirements.
• Using the OSD menu
1. Press MENU/EXIT on the projector or Menu on the remote control and then press 
/  until the DISPLAY menu is highlighted.
2. Press
 to highlight Aspect Ratio.
3. Press  /  to select an aspect ratio to suit the format of the video signal and your 
display requirements. 
						

							29
About the aspect ratio
In the pictures below, the black portions are inactive areas and the white portions are active 
areas. OSD menus can be displayed on those unused black areas.
1.Auto: Scales an image proportionally to fit the 
projector's native resolution in its horizontal 
width. This is suitable for the incoming image 
which is neither in 4:3 nor 16:9 and you want to 
make most use of the screen without altering the 
image's aspect ratio.
2.4:3: Scales an image so that it is displayed in the 
center of the screen with a 4:3 aspect ratio. This 
is most suitable for 4:3 images like computer 
monitors, standard definition TV and 4:3 aspect 
DVD movies, as it displays them without aspect 
alteration.
3.16:9: Scales an image so that it is displayed in 
the center of the screen with a 16:9 aspect ratio. 
This is most suitable for images which are 
already in a 16:9 aspect, like high definition TV, 
as it displays them without aspect alteration.
4.16:10 (PJD5533w only): Scales an image so 
that it is displayed in the center of the screen 
with a 16:10 aspect ratio. This is most suitable 
for images which are already in a 16:10 aspect, 
as it displays them without aspect alteration.
5.Wide (PJD5533w only): Scales a 4:3 aspect 
image vertically and horizontally in a non-linear 
manner so that it fills the screen with a 16:9 
aspect ratio.
16:10 picture
15:9 picture
4:3 picture
16:9 picture
16:10 picture
4:3 picture 
						

							30
6.Anamorphic (PJD5132/PJD5134/PJD5232L/
PJD5234L only): Scales a 16:9 aspect image 
vertically and horizontally in a non-linear 
manner so that it fills the screen with a 4:3 
aspect ratio.
16:9 picture 
						

							31
Optimizing the image
Selecting a picture mode
The projector is preset with several predefined picture modes so that you can choose one to 
suit your operating environment and input signal picture type.
To select an operation mode that suits your need, you can follow one of the following steps.
• Press MODE/ENTER on the projector or Color Mode on the remote control 
repeatedly until your desired mode is selected.
•Go to the PICTURE > Color Mode menu and press  /  to select a desired mode.
Picture modes for different types of signals
The picture modes available for different types of signals are listed below.
PC input signals: D-Sub / Comp. 1/2 (analog RGB)
1.Brightest mode: Maximizes the brightness of the projected image. This mode is 
suitable for environments where extra-high brightness is required, such as using the 
projector in well lit rooms.
2.PC mode: Is designed for presentations under daylight environment to match PC and 
notebook coloring.
3.ViewMatch mode: Switches between high brightness performance and accurate color 
performance.
4.Movie mode: Is appropriate for playing colorful movies, video clips from digital 
cameras or DVs through the PC input for best viewing in a blackened (little light) 
environment.
5.Dynamic PC mode: Is designed for presentations under daylight environment to 
match PC and notebook coloring. In addition, the projector will optimize the image 
quality using the dynamic PC function in accordance with the projected contents.
It takes some time to initiate this function. Make sure the projector has been turned on for 
more than 4 minutes.
If the projector is resumed by using the Smart Restart feature, this function can be executed 
immediately. 
6.Dynamic Movie mode: Is appropriate for playing colorful movies, video clips from 
digital cameras or DVs through the PC input for best viewing in a blackened (little 
light) environment. In addition, the projector will optimize the image quality using the 
dynamic Movie function in accordance with the projected contents.
It takes some time to initiate this function. Make sure the projector has been turned on for 
more than 4 minutes.
If the projector is resumed by using the Smart Restart feature, this function can be executed 
immediately. 
7.User 1/User 2 mode: Recalls the settings customized based on the current available 
picture modes. See "Setting the User 1/User 2 mode" on page 32 for details.
Video input signals: S-Video, Video, D-Sub / Comp. 1/2 (YPbPr) / HDMI
1.Brightest mode: Optimized for daylight viewing, with living room level ambient 
brightness.
2.Gaming mode: Suitable for all types of entertainment media, including gaming and 
movies.
3.ViewMatch mode: Switches between high brightness performance and accurate color 
performance. 
						

							32
4.Movie mode: Is suitable for enjoying dark movies or DVD movies best viewed in a 
blackened (little light) home cinema or lounge room environment.
5.Dynamic Movie mode: Is suitable for enjoying dark movies or DVD movies best 
viewed in a blackened (little light) home cinema or lounge room environment. In 
addition, the projector will optimize the image quality using the dynamic Movie 
function in accordance with the projected contents.
It takes some time to initiate this function. Make sure the projector has been turned on for 
more than 4 minutes.
If the projector is resumed by using the Smart Restart feature, this function can be executed 
immediately. 
6.User 1/User 2 mode: Recalls the settings customized based on the current available 
picture modes. See "Setting the User 1/User 2 mode" on page 32 for details.
Setting the User 1/User 2 mode
There are two user-definable modes if the current available picture modes are not suitable 
for your need. You can use one of the picture modes (except the User 1/User 2) as a starting 
point and customize the settings.
1. Press MENU/EXIT on the projector or Menu on the remote control to open the On-
Screen Display (OSD) menu.
2. Go to the PICTURE > Color Mode menu.
3. Press  /  to select User 1 or User 2.
4. Press to highlight Reference Mode.
This function is only available when User 1 or User 2 mode is selected up in the Color Mode 
sub-menu item.
5. Press  /  to select a picture mode that is closest to your need.
6. Press  to select a sub-menu item to be changed and adjust the value with  / . 
See Fine-tuning the image quality in user modesbelow for details.
7. When all settings have been done, highlight Save Settings and press MODE/ENTER
on the projector or Enter on the remote control to store the settings.
8. The confirmation message 'Setting Saved' is displayed.
Using Screen Color
In the situation where you are projecting onto a colored surface such as a painted wall which 
may not be white, the Screen Color feature can help correct the projected picture’s colors to 
prevent possible color difference between the source and projected pictures.
To use this function, go to the DISPLAY > Screen Color menu and press  /  to select a 
color which is closest to the color of the projection surface. There are several precalibrated 
colors to choose from: Whiteboard,Greenboard, and Blackboard.
This function is only available when a PC type input signal is selected.
Fine-tuning the image quality in user modes
According to the detected signal type, there are some user-definable functions available 
whenUser 1 or User 2 mode is selected. You can make adjustments to these functions 
based on your needs.
When you are done making adjustments, remember to go to the PICTURE > Save Settings
menu and press MODE/ENTER to save your settings. 
						

							33 Adjusting Brightness
Highlight the PICTURE > Brightness menu and press  /.
The higher the value, the brighter the image. And the 
lower the setting, the darker the image. Adjust this 
control so the black areas of the image appear just as 
black and that detail in the dark areas is visible.
Adjusting Contrast
Highlight the PICTURE > Contrast menu and press  / .
The higher the value, the greater the contrast. Use this 
to set the peak white level after you have previously 
adjusted the Brightness setting to suit your selected 
input and viewing environment.
Adjusting Color
Highlight the PICTURE > Color menu and press  / .
Lower setting produces less saturated colors. If the setting is too high, colors on the image 
will be overpowering, which makes the image unrealistic.
Adjusting Tint
Highlight the PICTURE > Tint menu and press  / .
The higher the value, the more reddish the picture becomes. The lower the value, the more 
greenish the picture becomes.
Adjusting Sharpness
Highlight the PICTURE > Sharpness menu and press  / .
The higher the value, the sharper the picture becomes. The lower the value, the softer the 
picture becomes.
Adjusting Brilliant Color
Highlight the PICTURE > Brilliant Color menu and press  / .
This feature utilizes a new color-processing algorithm and system level enhancements to 
enable higher brightness while providing truer, more vibrant colors in the projected picture. 
It enables a greater than 50% brightness increase in mid-tone images, which are common in 
video and natural scenes, so the projector reproduces images in realistic and true colors. If 
you prefer images with that quality, select On. If you don’t need it, select Off.
When Off is selected, the Color Temperature function is not available.
Selecting a Color Temperature
Highlight the PICTURE > Color Temperature menu and press  / .
The options available for color temperature* settings vary according to the signal type 
selected.
1.T1: With the highest color temperature, T1 makes the image appear the most bluish 
white than other settings.
2.T2: Makes images appear bluish white.
3.T3: Maintains normal colorings for white.
+50+30+70
0-30+30 
						

							34
4.T4: Makes images appear reddish white.
*About color temperatures:
There are many different shades that are considered to be "white" for various purposes. One 
of the common methods of representing white color is known as the “color temperature”. A 
white color with a low color temperature appears to be reddish white. A white color with a 
high color temperature appears to have more blue in it.
Color Management
Only in permanent installations with controlled lighting levels such as boardrooms, lecture 
theaters, or home theaters, should color management be considered. Color management 
provides fine color control adjustment to allow for more accurate color reproduction, should 
you require it.
If you have purchased a test disc which contains various color test patterns and can be used 
to test the color presentation on monitors, TVs, projectors, etc., you can project any image 
from the disc on the screen and enter the Color Management menu to make adjustments.
To adjust the settings:
1. Go to the DISPLAY menu and highlight Color Management.
2. Press MODE/ENTER on the projector or Enter on the remote control and the Color
Management page is displayed.
3. Highlight Primary Color and press  /  to select a color from among Red, Yellow, 
Green, Cyan, Blue, or Magenta.
4. Press  to highlight Hue and press  /  to select its range. Increase in the range 
will include colors consisted of more proportions of its two adjacent colors.
Please refer to the illustration to the right for 
how the colors relate to each other.
For example, if you select Red and set its 
range at 0, only pure red in the projected 
picture will be selected. Increasing its range 
will include red close to yellow and red close 
to magenta.
5. Press  to highlight Saturation and adjust 
its values to your preference by pressing  /
. Every adjustment made will reflect to the 
image immediately.
For example, if you select Red and set its 
value at 0, only the saturation of pure red will be affected.
Saturation is the amount of that color in a video picture. Lower settings produce less 
saturated colors; a setting of “0” removes that color from the image entirely. If the saturation 
is too high, that color will be overpowering and unrealistic.
6. Press  to highlight Gain and adjust its values to your preference by pressing  /
. The contrast level of the primary color you select will be affected. Every 
adjustment made will reflect to the image immediately. 
7. Repeat steps 3 to 6 for other color adjustments.
8. Make sure you have made all of the desired adjustments.
9. Press MENU/EXIT on the projector or Exit on the remote control to exit and save the 
settings.
RED
BLUEGREEN Yellow
Cyan
Magenta 
						

							35
Setting the presentation timer
Presentation timer can indicate the presentation time on the screen to help you achieve 
better time management when giving presentations. Follow these steps to utilize this 
function:
1. Press Timer on the remote control to access the Presentation Timer menu or go to 
theSYSTEM SETTING: ADVANCED > Presentation Timer menu and press
MODE/ENTER to display the Presentation Timer page.
2. Highlight Timer Period and decide the time period by pressing  / . The length of 
time can be set from 1 to 5 minutes in 1-minute increments and 5 to 240 minutes in 5-
minute increments.
If the timer is already on, the timer will restart whenever the Timer Period is reset.
3. Press  to highlight Timer Display and choose if you want the timer to show up on 
the screen by pressing /
.
4. Press  to highlight Timer Position and set the timer position by pressing  /.
5. Press  to highlight Timer Counting Direction and select your desired counting 
direction by pressing  / .
6. Press  to highlight Sound Reminder and decide if you want to activate sound 
reminder by pressing  / . If you select On, a double beep sound will be heard at 
the last 30 seconds of counting down/up, and a triple beep sound will be produced 
when the timer is up.
7. To activate the presentation timer, press   and press  /  to highlight Start
Counting and press MODE/ENTER.
8. A confirmation message displays. Highlight Ye s and press MODE/ENTER on the 
projector or remote control to confirm. You will see the message “Timer is On”
displaying on the screen. The timer starts counting when the timer is on.
To cancel the timer, perform the following steps:
1. Go to the SYSTEM SETTING: ADVANCED > Presentation Timer menu and 
highlight Off. Press MODE/ENTER. A confirmation message displays.
2. Highlight Ye s and press MODE/ENTER to confirm. You will see the message 
“Timer is Off” displaying on the screen.
SelectionDescription
AlwaysDisplays the timer on screen throughout the presentation 
time.
1 min/2 min/3 min  Displays the timer on screen in the last 1/2/3 minute(s).
Never Hides the timer throughout the presentation time.
Top-Left Bottom-Left Top-Right Bottom-Right
SelectionDescription
Count UpIncreases from 0 to the preset time.
Count DownDecreases from the preset time to 0.